> -----Original Message-----
> From: James Bottomley [mailto:[EMAIL PROTECTED]
> Sent: Wednesday, April 04, 2007 10:36 AM
> To: Ed Lin
> Cc: linux-scsi; linux-kernel; jeff; Promise_Linux
> Subject: RE: [PATCH 1/4] [SCSI]stex: fix id mapping issue
>
>
> On Wed, 2007-04-04 at 10:31 -0700, Ed Lin wrote:
>
> > Sorry. It seems the mail server has problem. The patch is
> here in plain
> > text. I hope this time it does not mess up. I have problem with
> > linux-scsi
> > mail list, if you have comment please cc me. Thanks.
> > --Ed Lin
>
> The lines are still broken, I'm afraid ... you can just resend as an
> attachement git-applypatch copes fine with that ... inline is
> just good
> for quoting and replying.
> > + if (hba->cardtype == st_shasta) {
> > + host->max_channel = 7;
> > + host->max_id = 16 + 1;
> > + } else if (hba->cardtype == st_yosemite) {
> > + host->max_channel = 127;
> > + host->max_id = 1 + 1;
> > + } else {
> > + /* st_vsc and st_vsc1 */
> > + host->max_channel = 0;
> > + host->max_id = 128 + 1;
>
> This is OK. The use of ->channel is still a bit strange ... could we
> not simply use lun instead of channel (i.e. map the adapter id/lun to
> the mid-layer id/lun instead of using id/channel)?
>
This is because there is a CONFIG_SCSI_MULTI_LUN option.
If this option is not selected, max_scsi_luns will be set to 1 and
the RAID arrays with lun>0 will disappear(because they are not
scanned). That is unacceptable from a user's view point. I have
also explained this in the code comment:
/*
* firmware uses id/lun pair for a logical drive, but lun would be
* always 0 if CONFIG_SCSI_MULTI_LUN not configured, so we use
* channel to map lun here
*/
If it is not allowed to map channel to lun, then maybe I have to
report 128 targets and do the mapping in queuecommand...
After all there must be a mapping somewhere so I don't see
much difference here...
I paste the patch again, is the format ok?
The internal id/lun mapping of st_vsc and st_vsc1 controllers is different
from st_shasta. The original driver code can only map first 16 'entities'
for st_vsc and st_vsc1 while there are actually 128 available.
The correct mapping should be:
channel:0~7, id:0~15 (st_shasta, console is channel:0, id:16, lun:0)
channel:0~127, id:0 (st_yosemite, console is channel:0, id:1, lun:0)
channel:0, id:0~127 (st_vsc and st_vsc1, console is channel:0, id:128, lun:0)
Signed-off-by: Ed Lin <[EMAIL PROTECTED]>
---
diff --git a/drivers/scsi/stex.c b/drivers/scsi/stex.c
index 69be132..29a7b61 100644
--- a/drivers/scsi/stex.c
+++ b/drivers/scsi/stex.c
@@ -113,10 +113,6 @@ enum {
SG_CF_64B = 0x40, /* 64 bit item */
SG_CF_HOST = 0x20, /* sg in host memory */
- ST_MAX_ARRAY_SUPPORTED = 16,
- ST_MAX_TARGET_NUM = (ST_MAX_ARRAY_SUPPORTED+1),
- ST_MAX_LUN_PER_TARGET = 16,
-
st_shasta = 0,
st_vsc = 1,
st_vsc1 = 2,
@@ -606,7 +602,7 @@ stex_queuecommand(struct scsi_cmnd *cmd,
return 0;
}
case INQUIRY:
- if (id != ST_MAX_ARRAY_SUPPORTED)
+ if (id != host->max_id - 1)
break;
if (lun == 0 && (cmd->cmnd[1] & INQUIRY_EVPD) == 0) {
stex_direct_copy(cmd, console_inq_page,
@@ -624,7 +620,7 @@ stex_queuecommand(struct scsi_cmnd *cmd,
ver.oem = ST_OEM;
ver.build = ST_BUILD_VER;
ver.signature[0] = PASSTHRU_SIGNATURE;
- ver.console_id = ST_MAX_ARRAY_SUPPORTED;
+ ver.console_id = host->max_id - 1;
ver.host_no = hba->host->host_no;
cmd->result = stex_direct_copy(cmd, &ver, sizeof(ver)) ?
DID_OK << 16 | COMMAND_COMPLETE << 8 :
@@ -645,13 +641,8 @@ stex_queuecommand(struct scsi_cmnd *cmd,
req = stex_alloc_req(hba);
- if (hba->cardtype == st_yosemite) {
- req->lun = lun * (ST_MAX_TARGET_NUM - 1) + id;
- req->target = 0;
- } else {
- req->lun = lun;
- req->target = id;
- }
+ req->lun = lun;
+ req->target = id;
/* cdb */
memcpy(req->cdb, cmd->cmnd, STEX_CDB_LENGTH);
@@ -1229,11 +1220,22 @@ stex_probe(struct pci_dev *pdev, const s
hba->copy_buffer = hba->dma_mem + MU_BUFFER_SIZE;
hba->mu_status = MU_STATE_STARTING;
- /* firmware uses id/lun pair for a logical drive, but lun would be
- always 0 if CONFIG_SCSI_MULTI_LUN not configured, so we use
- channel to map lun here */
- host->max_channel = ST_MAX_LUN_PER_TARGET - 1;
- host->max_id = ST_MAX_TARGET_NUM;
+ /*
+ * firmware uses id/lun pair for a logical drive, but lun would be
+ * always 0 if CONFIG_SCSI_MULTI_LUN not configured, so we use
+ * channel to map lun here
+ */
+ if (hba->cardtype == st_shasta) {
+ host->max_channel = 7;
+ host->max_id = 16 + 1;
+ } else if (hba->cardtype == st_yosemite) {
+ host->max_channel = 127;
+ host->max_id = 1 + 1;
+ } else {
+ /* st_vsc and st_vsc1 */
+ host->max_channel = 0;
+ host->max_id = 128 + 1;
+ }
host->max_lun = 1;
host->unique_id = host->host_no;
host->max_cmd_len = STEX_CDB_LENGTH;
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
