>>>>> "Sergei" == Sergei Shtylyov <[EMAIL PROTECTED]> writes:
Sergei> Hello. Sergei> John Stoffel wrote: >> I was just testing out 2.6.21-rc6-mm1 to test some Cyclades patches >> and I noticed that my HPT302 (rev1) controller with a pair of 120gb WD >> disks are not longer detected and I get the following in the dmesg >> logs: >> [ 148.121490] hpt37x: DPLL did not stabilize. >> Where before, under 2.6.21-rc6 I got the following: Sergei> For the moment I thought you're reporting another hpt366.c Sergei> driver breakage but then noticed the next line: I used to think that I wanted to use that driver too, but it's not going to work. It's because I've got the version 1 of the chip, not the newer version 2 or higher version. It looks like you really mean for me to use the hpt3x2.c driver instead, since that's the only other one which mentions the PCI_DEVICE_ID_TTI_HPT302 device id in it's init method. >> [ 173.749349] pata_hpt37x: BIOS has not set timing clocks. >> [ 173.752949] hpt37x: HPT302: Bus clock 33MHz. Sergei> Obviously this was bacause of switching from PCI to DPLL Sergei> clock. The old and new drivers are different in how they Sergei> handle DPLL calibration though. Could you try hpt366.c Sergei> (there's been report about its failure too recently -- not Sergei> enought details yet)? I don't think it will work here, it won't even touch the card since the pci_device_id won't match at all. The htp366.c only looks at HPT366 ids, while mine is an HPT302 id. As a quick note, 2.6.21-rc7 is working just fine here. >> [ 173.754409] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 18 (level, >> low) -> IRQ >> 18 >> [ 173.758403] ata5: PATA max UDMA/133 cmd 0x0001ecf8 ctl 0x0001ecf2 >> bmdma 0x000 >> 1e800 irq 18 >> [ 173.761396] ata6: PATA max UDMA/133 cmd 0x0001ece0 ctl 0x0001ecda >> bmdma 0x000 >> 1e808 irq 18 >> [ 173.764319] scsi6 : pata_hpt37x >> [ 173.928997] ATA: abnormal status 0x78 on port 0x0001ecff >> [ 173.930511] scsi7 : pata_hpt37x >> [ 174.094906] ATA: abnormal status 0x8 on port 0x0001ece7 >> Here's my lspci infomation on the board, it's an addon. My apologies >> for the crappy word wrapping, xterms inside screen, etc. >> 03:06.0 RAID bus controller: Triones Technologies, Inc. HPT302/302N >> (rev 01) >> Subsystem: Triones Technologies, Inc. Unknown device 0001 >> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- Step >> ping- SERR+ FastB2B- >> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >> >TAbort- <TAbort >> - <MAbort- >SERR- <PERR- >> Latency: 120 (2000ns min, 2000ns max) >> Interrupt: pin A routed to IRQ 11 >> Region 0: I/O ports at ecf8 [size=8] >> Region 1: I/O ports at ecf0 [size=4] >> Region 2: I/O ports at ece0 [size=8] >> Region 3: I/O ports at ecd8 [size=4] >> Region 4: I/O ports at e800 [size=256] >> Expansion ROM at f9000000 [disabled] [size=128K] >> Capabilities: [60] Power Management version 2 >> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA >> PME(D0-,D1-,D2-,D3hot >> -,D3cold-) >> Status: D0 PME-Enable- DSel=0 DScale=0 PME- Sergei> Yeah, that's a "plain" HPT302 chip with the default 66 MHz Sergei> DPLL clock. Ok, so do I need to do anything special with the next -mm release and the next version? Thanks, John - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/