Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
upstream-linus
to receive the following updates:
drivers/ata/ata_piix.c | 1 +
drivers/ata/libata-core.c | 4 +-
drivers/ata/pata_hpt3x2n.c | 4 +-
drivers/ata/pata_sis.c | 46 ++++++++++++++++++++++----------------------
drivers/ata/pata_via.c | 29 +++++++++++++++++++++++++++
5 files changed, 57 insertions(+), 27 deletions(-)
Alan Cox (3):
hpt3x2n: Correct revision boundary
pata_sis: Fix and clean up some timing setups
pata_via: Handle laptops via DMI
Tejun Heo (3):
ata_piix: add short 40c quirk for Acer Aspire 2030, take #2
libata: don't consider 0xff as port empty if SStatus is available
libata: -ENODEV during prereset isn't an error
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 0458811..9c07b88 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -578,6 +578,7 @@ static const struct ich_laptop ich_laptop[] = {
{ 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
{ 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
{ 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */
/* end marker */
{ 0, }
};
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index a6de57e..3ca9c61 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3022,7 +3022,7 @@ int ata_wait_ready(struct ata_port *ap, unsigned long
deadline)
if (!(status & ATA_BUSY))
return 0;
- if (status == 0xff)
+ if (!ata_port_online(ap) && status == 0xff)
return -ENODEV;
if (time_after(now, deadline))
return -EBUSY;
@@ -3368,7 +3368,7 @@ int ata_std_prereset(struct ata_port *ap, unsigned long
deadline)
*/
if (!(ap->flags & ATA_FLAG_SKIP_D2H_BSY) && !ata_port_offline(ap)) {
rc = ata_wait_ready(ap, deadline);
- if (rc) {
+ if (rc && rc != -ENODEV) {
ata_port_printk(ap, KERN_WARNING, "device not ready "
"(errno=%d), forcing hardreset\n", rc);
ehc->i.action |= ATA_EH_HARDRESET;
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index f25154a..e947433 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -521,8 +521,8 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const
struct pci_device_id *id)
/* 371N if rev > 1 */
break;
case PCI_DEVICE_ID_TTI_HPT372:
- /* 372N if rev >= 1*/
- if (class_rev == 0)
+ /* 372N if rev >= 2*/
+ if (class_rev < 2)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT302:
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index f223126..ec3ae93 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -73,14 +73,14 @@ static int sis_short_ata40(struct pci_dev *dev)
}
/**
- * sis_port_base - return PCI configuration base for dev
+ * sis_old_port_base - return PCI configuration base
for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
* number.
*/
-static int sis_port_base(struct ata_device *adev)
+static int sis_old_port_base(struct ata_device *adev)
{
return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno);
}
@@ -211,7 +211,7 @@ static void sis_set_fifo(struct ata_port *ap, struct
ata_device *adev)
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
@@ -248,7 +248,7 @@ static void sis_old_set_piomode (struct ata_port *ap,
struct ata_device *adev)
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
@@ -328,7 +328,7 @@ static void sis_old_set_dmamode (struct ata_port *ap,
struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
@@ -367,7 +367,7 @@ static void sis_66_set_dmamode (struct ata_port *ap, struct
ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
@@ -378,12 +378,12 @@ static void sis_66_set_dmamode (struct ata_port *ap,
struct ata_device *adev)
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device, bit 15 udma */
- timing &= ~ 0x870F;
+ timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x6000;
+ timing &= ~0xF000;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
@@ -405,22 +405,22 @@ static void sis_100_set_dmamode (struct ata_port *ap,
struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
- const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200,
0x8100};
+ const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
@@ -440,22 +440,22 @@ static void sis_133_early_set_dmamode (struct ata_port
*ap, struct ata_device *a
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
-
- static const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500,
0x8300, 0x8200, 0x8100};
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+ /* Low 4 bits are timing */
+ static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82,
0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index e4c71f7..708dfc0 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -60,6 +60,7 @@
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
+#include <linux/dmi.h>
#define DRV_NAME "pata_via"
#define DRV_VERSION "0.3.1"
@@ -122,6 +123,31 @@ static const struct via_isa_bridge {
{ NULL }
};
+
+/*
+ * Cable special cases
+ */
+
+static struct dmi_system_id cable_dmi_table[] = {
+ {
+ .ident = "Acer Ferrari 3400",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Acer,Inc."),
+ DMI_MATCH(DMI_BOARD_NAME, "Ferrari 3400"),
+ },
+ },
+ { }
+};
+
+static int via_cable_override(struct pci_dev *pdev)
+{
+ /* Systems by DMI */
+ if (dmi_check_system(cable_dmi_table))
+ return 1;
+ return 0;
+}
+
+
/**
* via_cable_detect - cable detection
* @ap: ATA port
@@ -139,6 +165,9 @@ static int via_cable_detect(struct ata_port *ap) {
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 ata66;
+ if (via_cable_override(pdev))
+ return ATA_CBL_PATA40_SHORT;
+
/* Early chips are 40 wire */
if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
return ATA_CBL_PATA40;
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
