On 28 June 2018 at 10:13, Stefan Agner <ste...@agner.ch> wrote:
> The field support_vsel is currently only used in the device tree
> case. Get rid of it. No change in behavior.
>
> Signed-off-by: Stefan Agner <ste...@agner.ch>
Thanks, applied for next!
Kind regards
Uffe
> ---
> drivers/mmc/host/sdhci-esdhc-imx.c | 8 ++------
> include/linux/platform_data/mmc-esdhc-imx.h | 2 --
> 2 files changed, 2 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c
> b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 6f444731754d..20a420b765b3 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -1145,18 +1145,14 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
> &boarddata->tuning_start_tap);
>
> if (of_find_property(np, "no-1-8-v", NULL))
> - boarddata->support_vsel = false;
> - else
> - boarddata->support_vsel = true;
> + host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
>
> if (of_property_read_u32(np, "fsl,delay-line",
> &boarddata->delay_line))
> boarddata->delay_line = 0;
>
> mmc_of_parse_voltage(np, &host->ocr_mask);
>
> - /* sdr50 and sdr104 need work on 1.8v signal voltage */
> - if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data) &&
> - !IS_ERR(imx_data->pins_default)) {
> + if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pins_default)) {
> imx_data->pins_100mhz =
> pinctrl_lookup_state(imx_data->pinctrl,
> ESDHC_PINCTRL_STATE_100MHZ);
> imx_data->pins_200mhz =
> pinctrl_lookup_state(imx_data->pinctrl,
> diff --git a/include/linux/platform_data/mmc-esdhc-imx.h
> b/include/linux/platform_data/mmc-esdhc-imx.h
> index 7daa78a2f342..640dec8b5b0c 100644
> --- a/include/linux/platform_data/mmc-esdhc-imx.h
> +++ b/include/linux/platform_data/mmc-esdhc-imx.h
> @@ -34,7 +34,6 @@ enum cd_types {
> * @cd_gpio: gpio for card_detect interrupt
> * @wp_type: type of write_protect method (see wp_types enum above)
> * @cd_type: type of card_detect method (see cd_types enum above)
> - * @support_vsel: indicate it supports 1.8v switching
> */
>
> struct esdhc_platform_data {
> @@ -43,7 +42,6 @@ struct esdhc_platform_data {
> enum wp_types wp_type;
> enum cd_types cd_type;
> int max_bus_width;
> - bool support_vsel;
> unsigned int delay_line;
> unsigned int tuning_step; /* The delay cell steps in tuning
> procedure */
> unsigned int tuning_start_tap; /* The start delay cell point in
> tuning procedure */
> --
> 2.18.0
>
