Ping for comments > -----Original Message----- > From: Jolly Shah [mailto:[email protected]] > Sent: Friday, November 16, 2018 3:57 PM > To: [email protected]; [email protected] > Cc: Michal Simek <[email protected]>; Rajan Vaja <[email protected]>; > Nava kishore Manne <[email protected]>; linux-arm- > [email protected]; [email protected]; > [email protected]; Jolly Shah <[email protected]> > Subject: [PATCH 0/9] dt-bindings: Firmware node binding for ZynqMP core > > Base firmware node and clock child node binding are part of mainline kernel. > This patchset adds documentation to describe rest of the firmware child node > bindings. > Complete firmware DT node example is shown below for ease of understanding: > > firmware { > zynqmp_firmware: zynqmp-firmware { > compatible = "xlnx,zynqmp-firmware"; > method = "smc"; > #power-domain-cells = <1>; > #reset-cells = <1>; > > zynqmp_clk: clock-controller { > #clock-cells = <1>; > compatible = "xlnx,zynqmp-clk"; > clocks = <&pss_ref_clk>, <&video_clk>, > <&pss_alt_ref_clk>, <&aux_ref_clk>, <>_crx_ref_clk>; > clock-names = "pss_ref_clk", "video_clk", > "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk"; > }; > > zynqmp_power: zynqmp-power { > compatible = "xlnx,zynqmp-power"; > interrupts = <0 35 4>; > }; > > nvmem_firmware { > compatible = "xlnx,zynqmp-nvmem-fw"; > #address-cells = <1>; > #size-cells = <1>; > > /* Data cells */ > soc_revision: soc_revision { > reg = <0x0 0x4>; > }; > }; > > afi0: afi0 { > compatible = "xlnx,afi-fpga"; > config-afi = <0 2>, <1 1>, <2 1>; > }; > > qspi: spi@ff0f0000 { > compatible = "xlnx,zynqmp-qspi-1.0"; > clock-names = "ref_clk", "pclk"; > clocks = <&misc_clk &misc_clk>; > interrupts = <0 15 4>; > interrupt-parent = <&gic>; > num-cs = <1>; > reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000 > 0x8000000>; > }; > > serdes: zynqmp_phy@fd400000 { > compatible = "xlnx,zynqmp-psgtr"; > status = "okay"; > reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 > 0x0 0x1000>, > <0x0 0xff5e0000 0x0 0x1000>; > reg-names = "serdes", "siou", "lpd"; > > lane0: lane@0 { > #phy-cells = <4>; > }; > lane1: lane@1 { > #phy-cells = <4>; > }; > lane2: lane@2 { > #phy-cells = <4>; > }; > lane3: lane@3 { > #phy-cells = <4>; > }; > }; > > pinctrl_uart1_default: uart1-default { > mux { > groups = "uart0_4_grp"; > function = "uart0"; > }; > > conf { > groups = "uart0_4_grp"; > slew-rate = <SLEW_RATE_SLOW>; > io-standard = <IO_STANDARD_LVCMOS18>; > }; > > conf-rx { > pins = "MIO18"; > bias-high-impedance; > }; > > conf-tx { > pins = "MIO19"; > bias-disable; > schmitt-cmos = <PIN_INPUT_TYPE_CMOS>; > }; > }; > zynqmp-r5-remoteproc@0 { > compatible = "xlnx,zynqmp-r5-remoteproc-1.0"; > reg = <0x0 0xFFE00000 0x0 0x10000>, > <0x0 0xFFE20000 0x0 0x10000>, > <0x0 0xff340000 0x0 0x100>; > reg-names = "tcm_a", "tcm_b", "ipi"; > dma-ranges; > core_conf = "split0"; > memory-region = <&rproc_0_fw_reserved>, > <&rproc_0_dma_reserved>; > tcm-pnode-id = <0xf>, <0x10>; > rpu-pnode-id = <0x7>; > interrupt-parent = <&gic>; > interrupts = <0 29 4>; > }; > }; > }; > > Jolly Shah (2): > dt-bindings: phy: Add dt bindings for ZynqMP PHY > dt-bindings: fpga: Add binding doc for the afi config driver > > Nava kishore Manne (2): > dt-bindings: reset: Add bindings for ZynqMP reset driver > dt-bindings: nvmem: Add bindings for ZynqMP nvmem driver > > Rajan Vaja (4): > dt-bindings: power: Add ZynqMP power domain bindings > dt-bindings: soc: Add ZynqMP PM bindings > dt-bindings: pinctrl: Add ZynqMP pin controller bindings > dt-bindings: spi: zynqmp: Move SPI node under zynqmp firmware > > Wendy Liang (1): > dt-bindings: remoteproc: Add Xilinx R5 rproc binding > > .../devicetree/bindings/fpga/xlnx,afi-fpga.txt | 67 +++++ > .../bindings/nvmem/xlnx,zynqmp-nvmem.txt | 44 ++++ > .../devicetree/bindings/phy/phy-zynqmp.txt | 126 ++++++++++ > .../bindings/pinctrl/xlnx,zynqmp-pinctrl.txt | 272 > +++++++++++++++++++++ > .../bindings/power/reset/xlnx,zynqmp-power.txt | 25 ++ > .../bindings/power/xlnx,zynqmp-genpd.txt | 34 +++ > .../remoteproc/xlnx,zynqmp-r5-remoteproc.txt | 81 ++++++ > .../bindings/reset/xlnx,zynqmp-reset.txt | 148 +++++++++++ > .../devicetree/bindings/spi/spi-zynqmp-qspi.txt | 22 +- > include/dt-bindings/power/xlnx-zynqmp-power.h | 39 +++ > 10 files changed, 850 insertions(+), 8 deletions(-) create mode 100644 > Documentation/devicetree/bindings/fpga/xlnx,afi-fpga.txt > create mode 100644 Documentation/devicetree/bindings/nvmem/xlnx,zynqmp- > nvmem.txt > create mode 100644 Documentation/devicetree/bindings/phy/phy-zynqmp.txt > create mode 100644 Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp- > pinctrl.txt > create mode 100644 > Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt > create mode 100644 Documentation/devicetree/bindings/power/xlnx,zynqmp- > genpd.txt > create mode 100644 > Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5- > remoteproc.txt > create mode 100644 Documentation/devicetree/bindings/reset/xlnx,zynqmp- > reset.txt > create mode 100644 include/dt-bindings/power/xlnx-zynqmp-power.h > > -- > 2.7.4
