[PATCH] iio: magnetometer: mag3110: add optional vcc regulator operation support

[Anson Huang]

The magnetometer's power supply could be controlled by regulator
on some platforms, such as i.MX6Q-SABRESD board, the mag3110's
power supply is controlled by a GPIO fixed regulator, need to make
sure the regulator is enabled before any communication with mag3110,
this patch adds optional vcc regulator operation support.

Signed-off-by: Anson Huang <anson.hu...@nxp.com>
---
 drivers/iio/magnetometer/mag3110.c | 49 +++++++++++++++++++++++++++++++++-----
 1 file changed, 43 insertions(+), 6 deletions(-)

diff --git a/drivers/iio/magnetometer/mag3110.c 
b/drivers/iio/magnetometer/mag3110.c
index f063355..e2d5b22 100644
--- a/drivers/iio/magnetometer/mag3110.c
+++ b/drivers/iio/magnetometer/mag3110.c
@@ -20,6 +20,7 @@
 #include <linux/iio/buffer.h>
 #include <linux/iio/triggered_buffer.h>
 #include <linux/delay.h>
+#include <linux/regulator/consumer.h>
 
 #define MAG3110_STATUS 0x00
 #define MAG3110_OUT_X 0x01 /* MSB first */
@@ -56,6 +57,7 @@ struct mag3110_data {
        struct mutex lock;
        u8 ctrl_reg1;
        int sleep_val;
+       struct regulator *vcc_reg;
 };
 
 static int mag3110_request(struct mag3110_data *data)
@@ -469,17 +471,27 @@ static int mag3110_probe(struct i2c_client *client,
        struct iio_dev *indio_dev;
        int ret;
 
+       indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+       if (!indio_dev)
+               return -ENOMEM;
+
+       data = iio_priv(indio_dev);
+
+       data->vcc_reg = devm_regulator_get_optional(&client->dev, "vcc");
+       if (!IS_ERR(data->vcc_reg)) {
+               ret = regulator_enable(data->vcc_reg);
+               if (ret) {
+                       dev_err(&client->dev, "failed to enable VCC 
regulator\n");
+                       return ret;
+               }
+       }
+
        ret = i2c_smbus_read_byte_data(client, MAG3110_WHO_AM_I);
        if (ret < 0)
                return ret;
        if (ret != MAG3110_DEVICE_ID)
                return -ENODEV;
 
-       indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
-       if (!indio_dev)
-               return -ENOMEM;
-
-       data = iio_priv(indio_dev);
        data->client = client;
        mutex_init(&data->lock);
 
@@ -537,14 +549,39 @@ static int mag3110_remove(struct i2c_client *client)
 #ifdef CONFIG_PM_SLEEP
 static int mag3110_suspend(struct device *dev)
 {
-       return mag3110_standby(iio_priv(i2c_get_clientdata(
+       struct mag3110_data *data = iio_priv(i2c_get_clientdata(
+               to_i2c_client(dev)));
+       int ret;
+
+       ret = mag3110_standby(iio_priv(i2c_get_clientdata(
                to_i2c_client(dev))));
+       if (ret)
+               return ret;
+
+       if (!IS_ERR(data->vcc_reg)) {
+               ret = regulator_disable(data->vcc_reg);
+               if (ret) {
+                       dev_err(dev, "failed to disable VCC regulator\n");
+                       return ret;
+               }
+       }
+
+       return 0;
 }
 
 static int mag3110_resume(struct device *dev)
 {
        struct mag3110_data *data = iio_priv(i2c_get_clientdata(
                to_i2c_client(dev)));
+       int ret;
+
+       if (!IS_ERR(data->vcc_reg)) {
+               ret = regulator_enable(data->vcc_reg);
+               if (ret) {
+                       dev_err(dev, "failed to enable VCC regulator\n");
+                       return ret;
+               }
+       }
 
        return i2c_smbus_write_byte_data(data->client, MAG3110_CTRL_REG1,
                data->ctrl_reg1);
-- 
2.7.4