Hi Vishal, On Mon, Jan 14, 2019 at 09:47:41AM +0000, Vishal Sagar wrote: > Hi Sakari, > > Thanks for reviewing this. > > > -----Original Message----- > > From: Sakari Ailus [mailto:sakari.ai...@linux.intel.com] > > Sent: Tuesday, January 08, 2019 6:35 PM > > To: Vishal Sagar <vishal.sa...@xilinx.com> > > Cc: Hyun Kwon <hy...@xilinx.com>; laurent.pinch...@ideasonboard.com; > > Michal Simek <mich...@xilinx.com>; linux-me...@vger.kernel.org; > > devicet...@vger.kernel.org; hans.verk...@cisco.com; mche...@kernel.org; > > robh...@kernel.org; mark.rutl...@arm.com; Dinesh Kumar > > <dine...@xilinx.com>; linux-arm-ker...@lists.infradead.org; linux- > > ker...@vger.kernel.org > > Subject: Re: [PATCH 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI > > CSI-2 > > Rx Subsystem > > > > EXTERNAL EMAIL > > > > Hi Vishal, > > > > The patchset hard escaped me somehow earlier and your reply to Rob made me > > notice it again. Thanks. :-) > > > > On Wed, May 30, 2018 at 12:24:43AM +0530, Vishal Sagar wrote: > > > Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem. > > > > > > The Xilinx MIPI CSI-2 Rx Subsystem consists of a DPHY, CSI-2 Rx, an > > > optional I2C controller and an optional Video Format Bridge (VFB). The > > > active lanes can be configured at run time if enabled in the IP. The > > > DPHY register interface may also be enabled. > > > > > > Signed-off-by: Vishal Sagar <vishal.sa...@xilinx.com> > > > --- > > > .../bindings/media/xilinx/xlnx,csi2rxss.txt | 117 > > +++++++++++++++++++++ > > > 1 file changed, 117 insertions(+) > > > create mode 100644 > > Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt > > > > > > diff --git > > > a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt > > b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt > > > new file mode 100644 > > > index 0000000..31ed721 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt > > > @@ -0,0 +1,117 @@ > > > + > > > > Extra newline. > > > > Will remove it in next version. > > > > +Xilinx MIPI CSI2 Receiver Subsystem Device Tree Bindings > > > +-------------------------------------------------------- > > > + > > > +The Xilinx MIPI CSI2 Receiver Subsystem is used to capture MIPI CSI2 > > > traffic > > > +from compliant camera sensors and send the output as AXI4 Stream video > > data > > > +for image processing. > > > + > > > +The subsystem consists of a MIPI DPHY in slave mode which captures the > > > +data packets. This is passed along the MIPI CSI2 Rx IP which extracts the > > > +packet data. This data is taken in by the Video Format Bridge (VFB), > > > +if selected, and converted into AXI4 Stream video data at selected > > > +pixels per clock as per AXI4-Stream Video IP and System Design UG934. > > > + > > > +For more details, please refer to PG232 MIPI CSI-2 Receiver Subsystem. > > > > > +https://www.xilinx.com/support/documentation/ip_documentation/mipi_csi > > 2_rx_subsystem/v3_0/pg232-mipi-csi2-rx.pdf > > > + > > > +Required properties: > > > + > > > +- compatible: Must contain "xlnx,mipi-csi2-rx-subsystem-2.0" or > > > + "xlnx,mipi-csi2-rx-subsystem-3.0" > > > + > > > +- reg: Physical base address and length of the registers set for the > > > device. > > > + > > > +- interrupt-parent: specifies the phandle to the parent interrupt > > > controller > > > + > > > +- interrupts: Property with a value describing the interrupt number. > > > + > > > +- xlnx,max-lanes: Maximum active lanes in the design. > > > + > > > +- xlnx,vc: Virtual Channel, specifies virtual channel number to be > > > filtered. > > > + If this is 4 then all virtual channels are allowed. > > > > This seems like something a driver should configure, based on the > > configuration of the connected device. > > > > The filtering of the Virtual channels is property of the hardware IP and is > fixed in design. > This is not software controlled.
So... you have different IP blocks between which (one of) the difference(s) is the virtual channel? > > > > + > > > +- xlnx,csi-pxl-format: This denotes the CSI Data type selected in hw > > > design. > > > + Packets other than this data type (except for RAW8 and User defined > > > data > > > + types) will be filtered out. Possible values are RAW6, RAW7, RAW8, > > > RAW10, > > > + RAW12, RAW14, RGB444, RGB555, RGB565, RGB666, RGB888 and > > YUV4228bit. > > > > This should be configured at runtime instead through V4L2 sub-device > > interface; it's not a property of the hardware. > > > > This too is a property of the hardware IP and is fixed to one data type > during design to reduce gate count. So for e.g. if RGB888 is selected > during design, then the hardware will only pass across RGB888 packet data > to output. (RAW8 packets are also allowed to pass through for all data > types selected) This is used in the driver to determine the media bus > format of the connected pads. If I understand this correctly, RAW8 and user defined data types will always pass through, plus the other data types listed here. Is that right? > > > > + > > > +- xlnx,axis-tdata-width: AXI Stream width, This denotes the AXI Stream > > > width. > > > + It depends on Data type chosen, Video Format Bridge enabled/disabled > > > and > > > + pixels per clock. If VFB is disabled then its value is either 0x20 (32 > > > bit) > > > + or 0x40(64 bit) width. > > > + > > > +- xlnx,video-format, xlnx,video-width: Video format and width, as > > > defined in > > > + video.txt. > > > > Ditto. > > > Again these are fixed values and can't be changed at run time. > These are used to determine the media bus format. What kind of values can the xlnx,video-format property have? How about xlnx.video-width? Where can video.txt be found? > > > > + > > > +- port: Video port, using the DT bindings defined in > > > ../video-interfaces.txt. > > > + The CSI 2 Rx Subsystem has a two ports, one input port for connecting > > > to > > > + camera sensor and other is output port. > > > + > > > +- data-lanes: The number of data lanes through which CSI2 Rx Subsystem is > > > + connected to the camera sensor as per video-interfaces.txt > > > > This is somewhat different from the documentation in video-interfaces.txt. > > Could you align the two? I don't think there's a need to document standard > > properties in device binding files elaborately; rather just the hardware > > specific bits. > > > > Agree. In this current IP there is no way to re-order the lanes which are set > at design time. > So physical and logical lanes are at same index. This could only be used to > determine how many lanes are allowed to be programmed. > For e.g. if design has set the number of lanes as 4 and xlnx,en-active-lanes > is present, then the number of lanes > can be set from 1 to 4. Ack. -- Regards, Sakari Ailus sakari.ai...@linux.intel.com
