On 28-01-19, 16:55, Quentin Perret wrote:
> diff --git a/drivers/opp/of.c b/drivers/opp/of.c
> index 06f0f632ec47..7572a2eb2fd4 100644
> --- a/drivers/opp/of.c
> +++ b/drivers/opp/of.c
> @@ -1047,3 +1047,63 @@ struct device_node *dev_pm_opp_get_of_node(struct
> dev_pm_opp *opp)
> return of_node_get(opp->np);
> }
> EXPORT_SYMBOL_GPL(dev_pm_opp_get_of_node);
> +
> +/**
> + * of_dev_pm_opp_get_cpu_power() - Estimates the power of a CPU
> + * @mW: pointer to the power estimate in milli-watts
> + * @KHz: pointer to the OPP's frequency, in kilo-hertz
> + * @cpu: CPU for which power needs to be estimated
> + *
> + * Computes the power estimated by @CPU at the first OPP above @KHz (ceil),
> + * and updates @KHz and @mW accordingly.
> + *
> + * The power is estimated as P = C * V^2 * f, with C the CPU's capacitance
> + * (read from the 'dynamic-power-coefficient' devicetree binding) and V and f
> + * respectively the voltage and frequency of the OPP.
> + *
> + * Return: -ENODEV if the CPU device cannot be found, -EINVAL if the power
> + * calculation failed because of missing parameters, 0 otherwise.
> + */
> +int of_dev_pm_opp_get_cpu_power(unsigned long *mW, unsigned long *KHz, int
> cpu)
I would suggest to change the return type to unsigned long and return 0 for
errors and positive values for mW.
> +{
> + unsigned long mV, Hz, MHz;
MHz is used only once, I think you can get rid of it just open code the division
by 1000000. Maybe remove Hz as well and directly use kHz.
> + struct device *cpu_dev;
> + struct dev_pm_opp *opp;
> + struct device_node *np;
> + u32 cap;
> + u64 tmp;
Name this mW with the above changes.
> + int ret;
> +
> + cpu_dev = get_cpu_device(cpu);
> + if (!cpu_dev)
> + return -ENODEV;
> +
> + np = of_node_get(cpu_dev->of_node);
> + if (!np)
> + return -EINVAL;
> +
> + ret = of_property_read_u32(np, "dynamic-power-coefficient", &cap);
> + of_node_put(np);
> + if (ret)
> + return -EINVAL;
> +
> + Hz = *KHz * 1000;
> + opp = dev_pm_opp_find_freq_ceil(cpu_dev, &Hz);
> + if (IS_ERR(opp))
> + return -EINVAL;
> +
> + mV = dev_pm_opp_get_voltage(opp) / 1000;
> + dev_pm_opp_put(opp);
> + if (!mV)
> + return -EINVAL;
> +
> + MHz = Hz / 1000000;
> + tmp = (u64)cap * mV * mV * MHz;
> + do_div(tmp, 1000000000);
> +
> + *mW = (unsigned long)tmp;
> + *KHz = Hz / 1000;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(of_dev_pm_opp_get_cpu_power);
> diff --git a/include/linux/pm_opp.h b/include/linux/pm_opp.h
> index 0a2a88e5a383..fedde14f5187 100644
> --- a/include/linux/pm_opp.h
> +++ b/include/linux/pm_opp.h
> @@ -322,6 +322,7 @@ int dev_pm_opp_of_get_sharing_cpus(struct device
> *cpu_dev, struct cpumask *cpuma
> struct device_node *dev_pm_opp_of_get_opp_desc_node(struct device *dev);
> struct device_node *dev_pm_opp_get_of_node(struct dev_pm_opp *opp);
> int of_get_required_opp_performance_state(struct device_node *np, int index);
> +int of_dev_pm_opp_get_cpu_power(unsigned long *mW, unsigned long *KHz, int
> cpu);
> #else
> static inline int dev_pm_opp_of_add_table(struct device *dev)
> {
> @@ -364,6 +365,10 @@ static inline int
> of_get_required_opp_performance_state(struct device_node *np,
> {
> return -ENOTSUPP;
> }
Add a blank line here. We missed adding the same before
of_get_required_opp_performance_state() earlier, maybe add the new routine
before of_get_required_opp_performance_state() and add blank line before and
after it :)
> +static inline int of_dev_pm_opp_get_cpu_power(unsigned long *mW, unsigned
> long *KHz, int cpu)
> +{
> + return -ENOTSUPP;
> +}
> #endif
>
> #endif /* __LINUX_OPP_H__ */
> --
> 2.20.1
--
viresh
