On 05.08.2019 18:54, Alexandru Ardelean wrote:
> This change adds support for enabling PHY interrupts that can be used by
> the PHY framework to get signal for link/speed/auto-negotiation changes.
>
> Signed-off-by: Alexandru Ardelean <alexandru.ardel...@analog.com>
> ---
> drivers/net/phy/adin.c | 44 ++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> index c100a0dd95cd..b75c723bda79 100644
> --- a/drivers/net/phy/adin.c
> +++ b/drivers/net/phy/adin.c
> @@ -14,6 +14,22 @@
> #define PHY_ID_ADIN1200 0x0283bc20
> #define PHY_ID_ADIN1300 0x0283bc30
>
> +#define ADIN1300_INT_MASK_REG 0x0018
> +#define ADIN1300_INT_MDIO_SYNC_EN BIT(9)
> +#define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8)
> +#define ADIN1300_INT_ANEG_PAGE_RX_EN BIT(6)
> +#define ADIN1300_INT_IDLE_ERR_CNT_EN BIT(5)
> +#define ADIN1300_INT_MAC_FIFO_OU_EN BIT(4)
> +#define ADIN1300_INT_RX_STAT_CHNG_EN BIT(3)
> +#define ADIN1300_INT_LINK_STAT_CHNG_EN BIT(2)
> +#define ADIN1300_INT_SPEED_CHNG_EN BIT(1)
> +#define ADIN1300_INT_HW_IRQ_EN BIT(0)
> +#define ADIN1300_INT_MASK_EN \
> + (ADIN1300_INT_ANEG_STAT_CHNG_EN | ADIN1300_INT_ANEG_PAGE_RX_EN | \
> + ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_SPEED_CHNG_EN | \
> + ADIN1300_INT_HW_IRQ_EN)
> +#define ADIN1300_INT_STATUS_REG 0x0019
> +
> static int adin_config_init(struct phy_device *phydev)
> {
> int rc;
> @@ -25,15 +41,40 @@ static int adin_config_init(struct phy_device *phydev)
> return 0;
> }
>
> +static int adin_phy_ack_intr(struct phy_device *phydev)
> +{
> + int ret;
> +
> + /* Clear pending interrupts. */
> + ret = phy_read(phydev, ADIN1300_INT_STATUS_REG);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int adin_phy_config_intr(struct phy_device *phydev)
> +{
> + if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
> + return phy_set_bits(phydev, ADIN1300_INT_MASK_REG,
> + ADIN1300_INT_MASK_EN);
> +
> + return phy_clear_bits(phydev, ADIN1300_INT_MASK_REG,
> + ADIN1300_INT_MASK_EN);
> +}
> +
> static struct phy_driver adin_driver[] = {
> {
> .phy_id = PHY_ID_ADIN1200,
> .name = "ADIN1200",
> .phy_id_mask = 0xfffffff0,
> .features = PHY_BASIC_FEATURES,
> + .flags = PHY_HAS_INTERRUPT,
This flag doesn't exist any longer. This indicates that you
develop against an older kernel version. Please develop
against net-next. Check up-to-date drivers like the one
for Realtek PHY's for hints.
> .config_init = adin_config_init,
> .config_aneg = genphy_config_aneg,
> .read_status = genphy_read_status,
> + .ack_interrupt = adin_phy_ack_intr,
> + .config_intr = adin_phy_config_intr,
> .resume = genphy_resume,
> .suspend = genphy_suspend,
> },
> @@ -42,9 +83,12 @@ static struct phy_driver adin_driver[] = {
> .name = "ADIN1300",
> .phy_id_mask = 0xfffffff0,
> .features = PHY_GBIT_FEATURES,
> + .flags = PHY_HAS_INTERRUPT,
> .config_init = adin_config_init,
> .config_aneg = genphy_config_aneg,
> .read_status = genphy_read_status,
> + .ack_interrupt = adin_phy_ack_intr,
> + .config_intr = adin_phy_config_intr,
> .resume = genphy_resume,
> .suspend = genphy_suspend,
> },
>
