Hi Vishal, Thank you for the patch.
On Wed, Apr 29, 2020 at 07:47:03PM +0530, Vishal Sagar wrote: > Add bindings documentation for Xilinx UHD-SDI Receiver Subsystem. > > The Xilinx UHD-SDI Receiver Subsystem consists of SMPTE UHD-SDI (RX) IP > core, an SDI RX to Video Bridge IP core to convert SDI video to native > video and a Video In to AXI4-Stream IP core to convert native video to > AXI4-Stream. > > Signed-off-by: Vishal Sagar <vishal.sa...@xilinx.com> > --- > v2 > - Removed references to xlnx,video* > - Fixed as per Sakari Ailus and Rob Herring's comments > - Converted to yaml format > > .../bindings/media/xilinx/xlnx,sdirxss.yaml | 132 ++++++++++++++++++ > 1 file changed, 132 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml > > diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml > b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml > new file mode 100644 > index 000000000000..9133ad19df55 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml > @@ -0,0 +1,132 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/xilinx/xlnx,sdirxss.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > + > +title: Xilinx SMPTE UHD-SDI Receiver Subsystem > + > +maintainers: > + - Vishal Sagar <vishal.sa...@xilinx.com> > + > +description: | > + The SMPTE UHD-SDI Receiver (RX) Subsystem allows you to quickly create > systems > + based on SMPTE SDI protocols. It receives unaligned native SDI streams from > + the SDI GT PHY and outputs an AXI4-Stream video stream, native video, or > + native SDI using Xilinx transceivers as the physical layer. > + > + The subsystem consists of > + 1 - SMPTE UHD-SDI Rx > + 2 - SDI Rx to Native Video Bridge > + 3 - Video In to AXI4-Stream Bridge > + > + The subsystem can capture SDI streams in upto 12G mode 8 data streams and > output s/upto/up to/ > + a dual pixel per clock RGB/YUV444,422/420 10/12 bits per component > AXI4-Stream. > + > +properties: > + compatible: > + items: > + - enum: > + - xlnx,v-smpte-uhdsdi-rx-ss-2.0 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + description: List of clock specifiers > + items: > + - description: AXI4-Lite clock > + - description: SMPTE UHD-SDI Rx core clock > + - description: Video clock > + > + clock-names: > + items: > + - const: s_axi_aclk > + - const: sdi_rx_clk > + - const: video_out_clk > + > + xlnx,bpp: > + description: Bits per pixel supported. Can be 10 or 12 bits per pixel > only. > + allOf: > + - $ref: "/schemas/types.yaml#/definitions/uint32" > + - enum: [10, 12] I don't see this as a design parameter in the documentation (pg290, v2.0). What does it correspond to ? All the BPC mentions in the documentation always state that 10-bit is the only supported value. > + > + xlnx,line-rate: > + description: | > + The maximum mode supported by the design. Possible values are as below > + 12G_SDI_8DS - 12G mode with 8 data streams > + 6G_SDI - 6G mode > + 3G_SDI - 3G mode > + enum: > + - 12G_SDI_8DS > + - 6G_SDI > + - 3G_SDI How about making this an integer property, with #define in include/dt-bindings/media/xilinx-sdi.h ? As far as I understand, the SDI TX subsystem has the same parameter, so the #define could be shared between the two. > + > + xlnx,include-edh: > + type: boolean > + description: | > + This is present when the Error Detection and Handling processor is > + enabled in design. > + > + ports: > + type: object > + description: | > + Generally the SDI port is connected to a device like SDI Broadcast > camera > + which is independently controlled. Hence port@0 is a source port which > can be > + connected to downstream IP which can work with AXI4 Stream data. We should still have an input port. It can be connected to a DT node for a physical SDI connector, or any other component in the platform (I expect the former to be the common case). There are DT bindings for connectors in Documentation/devicetree/bindings/display/connector/, we should add one for SDI. > + properties: > + port@0: > + type: object > + description: Source port > + properties: > + reg: > + const: 0 > + endpoint: > + type: object > + properties: > + remote-endpoint: true > + required: > + - remote-endpoint > + additionalProperties: false > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + - xlnx,line-rate > + - xlnx,bpp > + - ports > + > +additionalProperties: false > + > +examples: > + - | > + uhdsdirxss: v-smpte-uhdsdi-rxss@80000000 { > + compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0"; > + interrupt-parent = <&gic>; > + interrupts = <0 89 4>; > + reg = <0x0 0x80000000 0x0 0x10000>; > + xlnx,include-edh; > + xlnx,line-rate = "12G_SDI_8DS"; > + clocks = <&clk_1>, <&si570_1>, <&clk_2>; > + clock-names = "s_axi_aclk", "sdi_rx_clk", "video_out_clk"; > + xlnx,bpp = <10>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + port@0 { > + reg = <0>; > + sdirx_out: endpoint { > + remote-endpoint = <&vcap_sdirx_in>; > + }; > + }; > + }; > + }; -- Regards, Laurent Pinchart