3.16.84-rc1 review patch. If anyone has any objections, please let me know.
------------------ From: Alexandre Belloni <[email protected]> commit ee0aa926ddb0bd8ba59e33e3803b3b5804e3f5da upstream. Currently the maximum rate for peripheral clock is calculated based on a typical 133MHz MCK. The maximum frequency is defined in the datasheet as a ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the device trees to match the maximum rate based on 166MHz. Reported-by: Karl Rudbæk Olsen <[email protected]> Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Alexandre Belloni <[email protected]> [bwh: Backported to 3.16: uart0_clk is only defined in sama5d3_uart.dtsi] Signed-off-by: Ben Hutchings <[email protected]> --- --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -1031,43 +1031,43 @@ usart0_clk: usart0_clk { #clock-cells = <0>; reg = <12>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; usart1_clk: usart1_clk { #clock-cells = <0>; reg = <13>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; usart2_clk: usart2_clk { #clock-cells = <0>; reg = <14>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; usart3_clk: usart3_clk { #clock-cells = <0>; reg = <15>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; twi0_clk: twi0_clk { reg = <18>; #clock-cells = <0>; - atmel,clk-output-range = <0 16625000>; + atmel,clk-output-range = <0 41500000>; }; twi1_clk: twi1_clk { #clock-cells = <0>; reg = <19>; - atmel,clk-output-range = <0 16625000>; + atmel,clk-output-range = <0 41500000>; }; twi2_clk: twi2_clk { #clock-cells = <0>; reg = <20>; - atmel,clk-output-range = <0 16625000>; + atmel,clk-output-range = <0 41500000>; }; mci0_clk: mci0_clk { @@ -1083,19 +1083,19 @@ spi0_clk: spi0_clk { #clock-cells = <0>; reg = <24>; - atmel,clk-output-range = <0 133000000>; + atmel,clk-output-range = <0 166000000>; }; spi1_clk: spi1_clk { #clock-cells = <0>; reg = <25>; - atmel,clk-output-range = <0 133000000>; + atmel,clk-output-range = <0 166000000>; }; tcb0_clk: tcb0_clk { #clock-cells = <0>; reg = <26>; - atmel,clk-output-range = <0 133000000>; + atmel,clk-output-range = <0 166000000>; }; pwm_clk: pwm_clk { @@ -1106,7 +1106,7 @@ adc_clk: adc_clk { #clock-cells = <0>; reg = <29>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; dma0_clk: dma0_clk { @@ -1137,13 +1137,13 @@ ssc0_clk: ssc0_clk { #clock-cells = <0>; reg = <38>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; ssc1_clk: ssc1_clk { #clock-cells = <0>; reg = <39>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; sha_clk: sha_clk { --- a/arch/arm/boot/dts/sama5d3_can.dtsi +++ b/arch/arm/boot/dts/sama5d3_can.dtsi @@ -37,13 +37,13 @@ can0_clk: can0_clk { #clock-cells = <0>; reg = <40>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; can1_clk: can1_clk { #clock-cells = <0>; reg = <41>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; }; }; --- a/arch/arm/boot/dts/sama5d3_uart.dtsi +++ b/arch/arm/boot/dts/sama5d3_uart.dtsi @@ -42,13 +42,13 @@ uart0_clk: uart0_clk { #clock-cells = <0>; reg = <16>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; uart1_clk: uart1_clk { #clock-cells = <0>; reg = <17>; - atmel,clk-output-range = <0 66000000>; + atmel,clk-output-range = <0 83000000>; }; }; };
