Quoting Rajendra Nayak (2020-08-10 00:06:19)
> dev_pm_opp_set_rate() can now be called with freq = 0 inorder
> to either drop performance or bandwidth votes or to disable
> regulators on platforms which support them.
> In such cases, a subsequent call to dev_pm_opp_set_rate() with
> the same frequency ends up returning early because 'old_freq == freq'
> Instead make it fall through and put back the dropped performance
> and bandwidth votes and/or enable back the regulators.
> 
> Fixes: cd7ea582 ("opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop 
> performance votes")
> Reported-by: Sajida Bhanu <sbh...@codeaurora.org>
> Signed-off-by: Rajendra Nayak <rna...@codeaurora.org>
> ---
>  drivers/opp/core.c | 8 +++++++-
>  1 file changed, 7 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/opp/core.c b/drivers/opp/core.c
> index 0c8c74a..a994f30 100644
> --- a/drivers/opp/core.c
> +++ b/drivers/opp/core.c
> @@ -901,6 +901,9 @@ int dev_pm_opp_set_rate(struct device *dev, unsigned long 
> target_freq)
>  
>         /* Return early if nothing to do */
>         if (old_freq == freq) {
> +               if (opp_table->required_opp_tables || opp_table->regulators ||
> +                   opp_table->paths)
> +                       goto skip_clk_only;

This is a goto maze! Any chance we can clean this up?

        if (!opp_table->required_opp_tables && !opp_table->regulators &&
            !opp_table->paths)
            if (old_freq == freq) {
                    ret = 0
                    dev_dbg(..)
            } else if (!_get_opp_count(opp_table)) {
                    ret = _generic_set_opp_clk_only(dev, clk, freq);
            }
        } else {
                temp_freq = old_freq;
                old_opp = _find_freq_ceil(opp_table, &temp_freq);
                ...
                dev_pm_opp_put(opp);
        put_old_opp:
                if (!IS_ERR(old_opp))
                        dev_pm_opp_put(old_opp);
        }
put_opp_table:
        dev_pm_opp_put_opp_table(opp_table);

And that stuff in the else should probably go to another function.

>                 dev_dbg(dev, "%s: old/new frequencies (%lu Hz) are same, 
> nothing to do\n",
>                         __func__, freq);
>                 ret = 0;
> @@ -919,6 +922,7 @@ int dev_pm_opp_set_rate(struct device *dev, unsigned long 
> target_freq)
>                 goto put_opp_table;
>         }
>  
> +skip_clk_only:
>         temp_freq = old_freq;
>         old_opp = _find_freq_ceil(opp_table, &temp_freq);
>         if (IS_ERR(old_opp)) {
> @@ -954,8 +958,10 @@ int dev_pm_opp_set_rate(struct device *dev, unsigned 
> long target_freq)
>                                                  IS_ERR(old_opp) ? NULL : 
> old_opp->supplies,
>                                                  opp->supplies);
>         } else {
> +               ret = 0;
>                 /* Only frequency scaling */
> -               ret = _generic_set_opp_clk_only(dev, clk, freq);
> +               if (freq != old_freq)
> +                       ret = _generic_set_opp_clk_only(dev, clk, freq);
>         }

And write this as 

        else if (freq != old_freq) {
                ret = _generic_set_opp_clk_only(..)
        } else {
                ret = 0;
        }

Reply via email to