On Thu, Aug 20, 2020 at 04:38:32PM -0700, Azhar Shaikh wrote:
> As per USB Type-C Spec R2.0 section 4.5.1.2 (Connecting Sources and Sinks)
> and section 4.5.2.2 (Connection State Machine Requirements), the typical
> flow for configuring a device connected to a typeC port is as below:
> 
> 1. Source/sink detection
> 2. Orientation
> 3. Data role
> 4. VCONN
> 5. VBUS (USB Type-C currents)
> 6. The connector is now configured. We can start the PD communication
>    that should lead into configuration of the mux if we enter a mode.
> 
> But in existing code data role was set after the connector and mux are
> already configured. So fix this by following the spec to set the data
> role before the connector and mux are configured.
> 
> Signed-off-by: Azhar Shaikh <azhar.sha...@intel.com>
To be clear, I still maintain that the quoted section pertains to
*detection* of those various properties (which is handled by the TCPM in
the Chrome OS EC), and not any ordering for setting switches etc.

That said, I'm not opposed to the re-ordering, so:
Reviewed-by: Prashant Malani <pmal...@chromium.org>
> ---
> Changes in v4:
>  - No change
> 
> Changes in v3:
>  - New patch added
> 
>  drivers/platform/chrome/cros_ec_typec.c | 13 +++++++------
>  1 file changed, 7 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/platform/chrome/cros_ec_typec.c 
> b/drivers/platform/chrome/cros_ec_typec.c
> index 2b43e1176e73..9e4fad9ca59e 100644
> --- a/drivers/platform/chrome/cros_ec_typec.c
> +++ b/drivers/platform/chrome/cros_ec_typec.c
> @@ -516,6 +516,12 @@ static int cros_typec_configure_mux(struct 
> cros_typec_data *typec, int port_num,
>       if (ret)
>               return ret;
>  
> +     ret = usb_role_switch_set_role(typec->ports[port_num]->role_sw,
> +                                    pd_ctrl->role & PD_CTRL_RESP_ROLE_DATA
> +                                    ? USB_ROLE_HOST : USB_ROLE_DEVICE);
> +     if (ret)
> +             return ret;
> +
>       if (mux_flags & USB_PD_MUX_TBT_COMPAT_ENABLED) {
>               ret = cros_typec_enable_tbt(typec, port_num, pd_ctrl);
>       } else if (mux_flags & USB_PD_MUX_DP_ENABLED) {
> @@ -533,12 +539,7 @@ static int cros_typec_configure_mux(struct 
> cros_typec_data *typec, int port_num,
>               ret = -ENOTSUPP;
>       }
>  
> -     if (ret)
> -             return ret;
> -
> -     return usb_role_switch_set_role(typec->ports[port_num]->role_sw,
> -                                    pd_ctrl->role & PD_CTRL_RESP_ROLE_DATA
> -                                    ? USB_ROLE_HOST : USB_ROLE_DEVICE);
> +     return ret;
>  }
>  
>  static int cros_typec_port_update(struct cros_typec_data *typec, int 
> port_num)
> -- 
> 2.17.1
> 

Reply via email to