Hi Vladimir,
> This adds support for ESPRESSObin-Ultra from Globalscale.
>
> Specifications are similar to the base ESPRESSObin board, with main
> difference being being WAN port with PoE capability and 2 additional ethernet
> ports.
>
> Full specifications:
>
> 1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
> 1x Topaz 6341 Networking Switch
> 1GB DDR4
> 8GB eMMC
> 1x WAN with 30W POE
> 4x Gb LAN
> 1x RTC Clock and battery
> 1x DC Jack
> 1x USB 3.0 Type A
> 1x USB 2.0 Type A
> 1x SIM NanoSIM card Slot
> 1x Power Button
> 4x LED
> 1x Reset button
> 1x microUSB for UART
> 1x M.2 2280 slot for memory
> 1x 2x2 802.11ac Wi-Fi
> 1x MiniPCIE slot for Wi-Fi (PCIe interface)
>
> Signed-off-by: Vladimir Vid <vladimir....@sartura.hr>
Applied on mvebu/dt64
I know that usb3 node is not yet enabled but we are a really close to the
end of the merge window for ARM so let's have this version in 5.11, and
then we can improve it in future version.
Thanks,
Gregory
> ---
>
> v5 changes:
> - update ethernet-phy@1 to match reg value
>
> ---
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> .../marvell/armada-3720-espressobin-ultra.dts | 165 ++++++++++++++++++
> 2 files changed, 166 insertions(+)
> create mode 100644
> arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile
> b/arch/arm64/boot/dts/marvell/Makefile
> index 3e5f2e7a040c..094f451fdd1d 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -3,6 +3,7 @@
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
> b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
> new file mode 100644
> index 000000000000..c5eb3604dd5b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
> @@ -0,0 +1,165 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for ESPRESSObin-Ultra board.
> + * Copyright (C) 2019 Globalscale technologies, Inc.
> + *
> + * Jason Hung <jh...@globalscaletechnologies.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "armada-3720-espressobin.dtsi"
> +
> +/ {
> + model = "Globalscale Marvell ESPRESSOBin Ultra Board";
> + compatible = "globalscale,espressobin-ultra", "marvell,armada3720",
> + "marvell,armada3710";
> +
> + aliases {
> + /* ethernet1 is WAN port */
> + ethernet1 = &switch0port5;
> + ethernet2 = &switch0port1;
> + ethernet3 = &switch0port2;
> + ethernet4 = &switch0port3;
> + ethernet5 = &switch0port4;
> + };
> +
> + reg_usb3_vbus: usb3-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb3-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&gpionb 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + usb3_phy: usb3-phy {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <®_usb3_vbus>;
> + };
> +
> + gpio-leds {
> + pinctrl-names = "default";
> + compatible = "gpio-leds";
> + /* No assigned functions to the LEDs by default */
> + led1 {
> + label = "ebin-ultra:blue:led1";
> + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> + };
> + led2 {
> + label = "ebin-ultra:green:led2";
> + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> + };
> + led3 {
> + label = "ebin-ultra:red:led3";
> + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> + };
> + led4 {
> + label = "ebin-ultra:yellow:led4";
> + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&sdhci0 {
> + status = "okay";
> +};
> +
> +&sdhci1 {
> + status = "disabled";
> +};
> +
> +&spi0 {
> + flash@0 {
> + spi-max-frequency = <108000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "firmware";
> + reg = <0x0 0x3e0000>;
> + };
> + partition@3e0000 {
> + label = "hw-info";
> + reg = <0x3e0000 0x10000>;
> + read-only;
> + };
> + partition@3f0000 {
> + label = "u-boot-env";
> + reg = <0x3f0000 0x10000>;
> + };
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> +
> + clock-frequency = <100000>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> +};
> +
> +&usb3 {
> + usb-phy = <&usb3_phy>;
> + status = "disabled";
> +};
> +
> +&mdio {
> + extphy: ethernet-phy@1 {
> + reg = <1>;
> + };
> +};
> +
> +&switch0 {
> + reg = <3>;
> +
> + ports {
> + switch0port1: port@1 {
> + reg = <1>;
> + label = "lan0";
> + phy-handle = <&switch0phy0>;
> + };
> +
> + switch0port2: port@2 {
> + reg = <2>;
> + label = "lan1";
> + phy-handle = <&switch0phy1>;
> + };
> +
> + switch0port3: port@3 {
> + reg = <3>;
> + label = "lan2";
> + phy-handle = <&switch0phy2>;
> + };
> +
> + switch0port4: port@4 {
> + reg = <4>;
> + label = "lan3";
> + phy-handle = <&switch0phy3>;
> + };
> +
> + switch0port5: port@5 {
> + reg = <5>;
> + label = "wan";
> + phy-handle = <&extphy>;
> + phy-mode = "sgmii";
> + };
> + };
> +
> + mdio {
> + switch0phy3: switch0phy3@14 {
> + reg = <0x14>;
> + };
> + };
> +};
> --
> 2.27.0
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
