From: Romain Liévin <[EMAIL PROTECTED]> tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access to Texas Instruments parallel link cable. A user-land method now exists thru PPDEV & PARPORT. Signed-off-by: Romain Liévin <[EMAIL PROTECTED]> Signed-off-by: Greg Kroah-Hartman <[EMAIL PROTECTED]> --- Documentation/tipar.txt | 93 -------- MAINTAINERS | 5 - drivers/char/Kconfig | 22 -- drivers/char/tipar.c | 557 ----------------------------------------------- include/linux/ticable.h | 44 ---- 5 files changed, 0 insertions(+), 721 deletions(-) delete mode 100644 Documentation/tipar.txt delete mode 100644 drivers/char/tipar.c delete mode 100644 include/linux/ticable.h diff --git a/Documentation/tipar.txt b/Documentation/tipar.txt deleted file mode 100644 index 67133ba..0000000 --- a/Documentation/tipar.txt +++ /dev/null @@ -1,93 +0,0 @@ - - Parallel link cable for Texas Instruments handhelds - =================================================== - - -Author: Romain Lievin -Homepage: http://lpg.ticalc.org/prj_tidev/index.html - - -INTRODUCTION: - -This is a driver for the very common home-made parallel link cable, a cable -designed for connecting TI8x/9x graphing calculators (handhelds) to a computer -or workstation (Alpha, Sparc). Given that driver is built on parport, the -parallel port abstraction layer, this driver is architecture-independent. - -It can also be used with another device plugged on the same port (such as a -ZIP drive). I have a 100MB ZIP and both of them work fine! - -If you need more information, please visit the 'TI drivers' homepage at the URL -above. - -WHAT YOU NEED: - -A TI calculator and a program capable of communicating with your calculator. - -TiLP will work for sure (since I am its developer!). yal92 may be able to use -it by changing tidev for tipar (may require some hacking...). - -HOW TO USE IT: - -You must have first compiled parport support (CONFIG_PARPORT_DEV): either -compiled in your kernel, either as a module. - -Next, (as root): - - modprobe parport - modprobe tipar - -If it is not already there (it usually is), create the device: - - mknod /dev/tipar0 c 115 0 - mknod /dev/tipar1 c 115 1 - mknod /dev/tipar2 c 115 2 - -You will have to set permissions on this device to allow you to read/write -from it: - - chmod 666 /dev/tipar[0..2] - -Now you are ready to run a linking program such as TiLP. Be sure to configure -it properly (RTFM). - -MODULE PARAMETERS: - - You can set these with: modprobe tipar NAME=VALUE - There is currently no way to set these on a per-cable basis. - - NAME: timeout - TYPE: integer - DEFAULT: 15 - DESC: Timeout value in tenth of seconds. If no data is available once this - time has expired then the driver will return with a timeout error. - - NAME: delay - TYPE: integer - DEFAULT: 10 - DESC: Inter-bit delay in micro-seconds. A lower value gives an higher data - rate but makes transmission less reliable. - -These parameters can be changed at run time by any program via ioctl(2) calls -as listed in ./include/linux/ticable.h. - -Rather than write 50 pages describing the ioctl() and so on, it is -perhaps more useful you look at ticables library (dev_link.c) that demonstrates -how to use them, and demonstrates the features of the driver. This is -probably a lot more useful to people interested in writing applications -that will be using this driver. - -QUIRKS/BUGS: - -None. - -HOW TO CONTACT US: - -You can email me at [EMAIL PROTECTED] Please prefix the subject line -with "TIPAR: " so that I am certain to notice your message. -You can also mail JB at [EMAIL PROTECTED] He packaged these drivers for Debian. - -CREDITS: - -The code is based on tidev.c & parport.c. -The driver has been developed independently of Texas Instruments. diff --git a/MAINTAINERS b/MAINTAINERS index 9507b42..a7caced 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3699,11 +3699,6 @@ M: [EMAIL PROTECTED] L: linux-kernel@vger.kernel.org S: Maintained -TI PARALLEL LINK CABLE DRIVER -P: Romain Lievin -M: [EMAIL PROTECTED] -S: Maintained - TIPC NETWORK LAYER P: Per Liden M: [EMAIL PROTECTED] diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index a509b8d..ef1ed5d 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -543,28 +543,6 @@ config PPDEV If unsure, say N. -config TIPAR - tristate "Texas Instruments parallel link cable support" - depends on PARPORT - ---help--- - If you own a Texas Instruments graphing calculator and use a - parallel link cable, then you might be interested in this driver. - - If you enable this driver, you will be able to communicate with - your calculator through a set of device nodes under /dev. The - main advantage of this driver is that you don't have to be root - to use this precise link cable (depending on the permissions on - the device nodes, though). - - To compile this driver as a module, choose M here: the - module will be called tipar. - - If you don't know what a parallel link cable is or what a Texas - Instruments graphing calculator is, then you probably don't need this - driver. - - If unsure, say N. - config HVC_DRIVER bool help diff --git a/drivers/char/tipar.c b/drivers/char/tipar.c deleted file mode 100644 index cef55c4..0000000 --- a/drivers/char/tipar.c +++ /dev/null @@ -1,557 +0,0 @@ -/* Hey EMACS -*- linux-c -*- - * - * tipar - low level driver for handling a parallel link cable designed - * for Texas Instruments graphing calculators (http://lpg.ticalc.org). - * A part of the TiLP project. - * - * Copyright (C) 2000-2002, Romain Lievin <[EMAIL PROTECTED]> - * under the terms of the GNU General Public License. - * - * Various fixes & clean-up from the Linux Kernel Mailing List - * (Alan Cox, Richard B. Johnson, Christoph Hellwig). - */ - -/* This driver should, in theory, work with any parallel port that has an - * appropriate low-level driver; all I/O is done through the parport - * abstraction layer. - * - * If this driver is built into the kernel, you can configure it using the - * kernel command-line. For example: - * - * tipar=timeout,delay (set timeout and delay) - * - * If the driver is loaded as a module, similar functionality is available - * using module parameters. The equivalent of the above commands would be: - * - * # insmod tipar timeout=15 delay=10 - */ - -/* COMPATIBILITY WITH OLD KERNELS - * - * Usually, parallel cables were bound to ports at - * particular I/O addresses, as follows: - * - * tipar0 0x378 - * tipar1 0x278 - * tipar2 0x3bc - * - * - * This driver, by default, binds tipar devices according to parport and - * the minor number. - * - */ -#undef DEBUG /* change to #define to get debugging - * output - for pr_debug() */ -#include <linux/module.h> -#include <linux/types.h> -#include <linux/errno.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/delay.h> -#include <linux/fcntl.h> -#include <linux/fs.h> -#include <linux/init.h> -#include <asm/uaccess.h> -#include <linux/ioport.h> -#include <asm/io.h> -#include <linux/bitops.h> -#include <linux/parport.h> /* Our code depend on parport */ -#include <linux/device.h> - -/* - * TI definitions - */ -#include <linux/ticable.h> - -/* - * Version Information - */ -#define DRIVER_VERSION "1.19" -#define DRIVER_AUTHOR "Romain Lievin <[EMAIL PROTECTED]>" -#define DRIVER_DESC "Device driver for TI/PC parallel link cables" -#define DRIVER_LICENSE "GPL" - -#define VERSION(ver,rel,seq) (((ver)<<16) | ((rel)<<8) | (seq)) - -/* ----- global variables --------------------------------------------- */ - -struct tipar_struct { - struct pardevice *dev; /* Parport device entry */ -}; - -#define PP_NO 3 -static struct tipar_struct table[PP_NO]; - -static int delay = IO_DELAY; /* inter-bit delay in microseconds */ -static int timeout = TIMAXTIME; /* timeout in tenth of seconds */ - -static unsigned int tp_count; /* tipar count */ -static unsigned long opened; /* opened devices */ - -static struct class *tipar_class; - -/* --- macros for parport access -------------------------------------- */ - -#define r_dtr(x) (parport_read_data(table[(x)].dev->port)) -#define r_str(x) (parport_read_status(table[(x)].dev->port)) -#define w_ctr(x,y) (parport_write_control(table[(x)].dev->port, (y))) -#define w_dtr(x,y) (parport_write_data(table[(x)].dev->port, (y))) - -/* --- setting states on the D-bus with the right timing: ------------- */ - -static inline void -outbyte(int value, int minor) -{ - w_dtr(minor, value); -} - -static inline int -inbyte(int minor) -{ - return (r_str(minor)); -} - -static inline void -init_ti_parallel(int minor) -{ - outbyte(3, minor); -} - -/* ----- global defines ----------------------------------------------- */ - -#define START(x) { x = jiffies + (HZ * timeout) / 10; } -#define WAIT(x) { \ - if (time_before((x), jiffies)) return -1; \ - if (need_resched()) schedule(); } - -/* ----- D-bus bit-banging functions ---------------------------------- */ - -/* D-bus protocol (45kbit/s max): - 1 0 0 - _______ ______|______ __________|________ __________ -Red : ________ | ____ | ____ - _ ____________|________ ______|__________ _____ -White: ________ | ______ | _______ -*/ - -/* Try to transmit a byte on the specified port (-1 if error). */ -static int -put_ti_parallel(int minor, unsigned char data) -{ - unsigned int bit; - unsigned long max; - - for (bit = 0; bit < 8; bit++) { - if (data & 1) { - outbyte(2, minor); - START(max); - do { - WAIT(max); - } while (inbyte(minor) & 0x10); - - outbyte(3, minor); - START(max); - do { - WAIT(max); - } while (!(inbyte(minor) & 0x10)); - } else { - outbyte(1, minor); - START(max); - do { - WAIT(max); - } while (inbyte(minor) & 0x20); - - outbyte(3, minor); - START(max); - do { - WAIT(max); - } while (!(inbyte(minor) & 0x20)); - } - - data >>= 1; - udelay(delay); - - if (need_resched()) - schedule(); - } - - return 0; -} - -/* Receive a byte on the specified port or -1 if error. */ -static int -get_ti_parallel(int minor) -{ - unsigned int bit; - unsigned char v, data = 0; - unsigned long max; - - for (bit = 0; bit < 8; bit++) { - START(max); - do { - WAIT(max); - } while ((v = inbyte(minor) & 0x30) == 0x30); - - if (v == 0x10) { - data = (data >> 1) | 0x80; - outbyte(1, minor); - START(max); - do { - WAIT(max); - } while (!(inbyte(minor) & 0x20)); - outbyte(3, minor); - } else { - data = data >> 1; - outbyte(2, minor); - START(max); - do { - WAIT(max); - } while (!(inbyte(minor) & 0x10)); - outbyte(3, minor); - } - - udelay(delay); - if (need_resched()) - schedule(); - } - - return (int) data; -} - -/* Try to detect a parallel link cable on the specified port */ -static int -probe_ti_parallel(int minor) -{ - int i; - int seq[] = { 0x00, 0x20, 0x10, 0x30 }; - int data; - - for (i = 3; i >= 0; i--) { - outbyte(3, minor); - outbyte(i, minor); - udelay(delay); - data = inbyte(minor) & 0x30; - pr_debug("tipar: Probing -> %i: 0x%02x 0x%02x\n", i, - data, seq[i]); - if (data != seq[i]) { - outbyte(3, minor); - return -1; - } - } - - outbyte(3, minor); - return 0; -} - -/* ----- kernel module functions--------------------------------------- */ - -static int -tipar_open(struct inode *inode, struct file *file) -{ - unsigned int minor = iminor(inode) - TIPAR_MINOR; - - if (tp_count == 0 || minor > tp_count - 1) - return -ENXIO; - - if (test_and_set_bit(minor, &opened)) - return -EBUSY; - - if (!table[minor].dev) { - printk(KERN_ERR "%s: NULL device for minor %u\n", - __FUNCTION__, minor); - return -ENXIO; - } - parport_claim_or_block(table[minor].dev); - init_ti_parallel(minor); - parport_release(table[minor].dev); - - return nonseekable_open(inode, file); -} - -static int -tipar_close(struct inode *inode, struct file *file) -{ - unsigned int minor = iminor(inode) - TIPAR_MINOR; - - if (minor > tp_count - 1) - return -ENXIO; - - clear_bit(minor, &opened); - - return 0; -} - -static ssize_t -tipar_write (struct file *file, const char __user *buf, size_t count, - loff_t * ppos) -{ - unsigned int minor = iminor(file->f_path.dentry->d_inode) - TIPAR_MINOR; - ssize_t n; - - parport_claim_or_block(table[minor].dev); - - for (n = 0; n < count; n++) { - unsigned char b; - - if (get_user(b, buf + n)) { - n = -EFAULT; - goto out; - } - - if (put_ti_parallel(minor, b) == -1) { - init_ti_parallel(minor); - n = -ETIMEDOUT; - goto out; - } - } - out: - parport_release(table[minor].dev); - return n; -} - -static ssize_t -tipar_read(struct file *file, char __user *buf, size_t count, loff_t * ppos) -{ - int b = 0; - unsigned int minor = iminor(file->f_path.dentry->d_inode) - TIPAR_MINOR; - ssize_t retval = 0; - ssize_t n = 0; - - if (count == 0) - return 0; - - parport_claim_or_block(table[minor].dev); - - while (n < count) { - b = get_ti_parallel(minor); - if (b == -1) { - init_ti_parallel(minor); - retval = -ETIMEDOUT; - goto out; - } else { - if (put_user(b, buf + n)) { - retval = -EFAULT; - break; - } else - retval = ++n; - } - - /* Non-blocking mode : try again ! */ - if (file->f_flags & O_NONBLOCK) { - retval = -EAGAIN; - goto out; - } - - /* Signal pending, try again ! */ - if (signal_pending(current)) { - retval = -ERESTARTSYS; - goto out; - } - - if (need_resched()) - schedule(); - } - - out: - parport_release(table[minor].dev); - return retval; -} - -static int -tipar_ioctl(struct inode *inode, struct file *file, - unsigned int cmd, unsigned long arg) -{ - int retval = 0; - - switch (cmd) { - case IOCTL_TIPAR_DELAY: - delay = (int)arg; //get_user(delay, &arg); - break; - case IOCTL_TIPAR_TIMEOUT: - if (arg != 0) - timeout = (int)arg; - else - retval = -EINVAL; - break; - default: - retval = -ENOTTY; - break; - } - - return retval; -} - -/* ----- kernel module registering ------------------------------------ */ - -static const struct file_operations tipar_fops = { - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = tipar_read, - .write = tipar_write, - .ioctl = tipar_ioctl, - .open = tipar_open, - .release = tipar_close, -}; - -/* --- initialisation code ------------------------------------- */ - -#ifndef MODULE -/* You must set these - there is no sane way to probe for this cable. - * You can use 'tipar=timeout,delay' to set these now. */ -static int __init -tipar_setup(char *str) -{ - int ints[3]; - - str = get_options(str, ARRAY_SIZE(ints), ints); - - if (ints[0] > 0) { - if (ints[1] != 0) - timeout = ints[1]; - else - printk(KERN_WARNING "tipar: bad timeout value (0), " - "using default value instead"); - if (ints[0] > 1) { - delay = ints[2]; - } - } - - return 1; -} -#endif - -/* - * Register our module into parport. - * Pass also 2 callbacks functions to parport: a pre-emptive function and an - * interrupt handler function (unused). - * Display a message such "tipar0: using parport0 (polling)". - */ -static int -tipar_register(int nr, struct parport *port) -{ - int err = 0; - - /* Register our module into parport */ - table[nr].dev = parport_register_device(port, "tipar", - NULL, NULL, NULL, 0, - (void *) &table[nr]); - - if (table[nr].dev == NULL) { - err = 1; - goto out; - } - - device_create(tipar_class, port->dev, MKDEV(TIPAR_MAJOR, - TIPAR_MINOR + nr), "par%d", nr); - - /* Display informations */ - pr_info("tipar%d: using %s (%s)\n", nr, port->name, (port->irq == - PARPORT_IRQ_NONE) ? "polling" : "interrupt-driven"); - - if (probe_ti_parallel(nr) != -1) - pr_info("tipar%d: link cable found\n", nr); - else - pr_info("tipar%d: link cable not found\n", nr); - - err = 0; - -out: - return err; -} - -static void -tipar_attach(struct parport *port) -{ - if (tp_count == PP_NO) { - pr_info("tipar: ignoring parallel port (max. %d)\n", PP_NO); - return; - } - - if (!tipar_register(tp_count, port)) - tp_count++; -} - -static void -tipar_detach(struct parport *port) -{ - /* Nothing to do */ -} - -static struct parport_driver tipar_driver = { - .name = "tipar", - .attach = tipar_attach, - .detach = tipar_detach, -}; - -static int __init -tipar_init_module(void) -{ - int err = 0; - - pr_info("tipar: parallel link cable driver, version %s\n", - DRIVER_VERSION); - - if (register_chrdev(TIPAR_MAJOR, "tipar", &tipar_fops)) { - printk(KERN_ERR "tipar: unable to get major %d\n", TIPAR_MAJOR); - err = -EIO; - goto out; - } - - tipar_class = class_create(THIS_MODULE, "ticables"); - if (IS_ERR(tipar_class)) { - err = PTR_ERR(tipar_class); - goto out_chrdev; - } - if (parport_register_driver(&tipar_driver)) { - printk(KERN_ERR "tipar: unable to register with parport\n"); - err = -EIO; - goto out_class; - } - - err = 0; - goto out; - -out_class: - class_destroy(tipar_class); - -out_chrdev: - unregister_chrdev(TIPAR_MAJOR, "tipar"); -out: - return err; -} - -static void __exit -tipar_cleanup_module(void) -{ - unsigned int i; - - /* Unregistering module */ - parport_unregister_driver(&tipar_driver); - - unregister_chrdev(TIPAR_MAJOR, "tipar"); - - for (i = 0; i < PP_NO; i++) { - if (table[i].dev == NULL) - continue; - parport_unregister_device(table[i].dev); - device_destroy(tipar_class, MKDEV(TIPAR_MAJOR, i)); - } - class_destroy(tipar_class); - - pr_info("tipar: module unloaded\n"); -} - -/* --------------------------------------------------------------------- */ - -__setup("tipar=", tipar_setup); -module_init(tipar_init_module); -module_exit(tipar_cleanup_module); - -MODULE_AUTHOR(DRIVER_AUTHOR); -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE(DRIVER_LICENSE); - -module_param(timeout, int, 0); -MODULE_PARM_DESC(timeout, "Timeout (default=1.5 seconds)"); -module_param(delay, int, 0); -MODULE_PARM_DESC(delay, "Inter-bit delay (default=10 microseconds)"); diff --git a/include/linux/ticable.h b/include/linux/ticable.h deleted file mode 100644 index 8c22120..0000000 --- a/include/linux/ticable.h +++ /dev/null @@ -1,44 +0,0 @@ -/* Hey EMACS -*- linux-c -*- - * - * tipar/tiser/tiusb - low level driver for handling link cables - * designed for Texas Instruments graphing calculators. - * - * Copyright (C) 2000-2002, Romain Lievin <[EMAIL PROTECTED]> - * - * Redistribution of this file is permitted under the terms of the GNU - * Public License (GPL) - */ - -#ifndef _TICABLE_H -#define _TICABLE_H 1 - -/* Internal default constants for the kernel module */ -#define TIMAXTIME 15 /* 1.5 seconds */ -#define IO_DELAY 10 /* 10 micro-seconds */ - -/* Major & minor number for character devices */ -#define TIPAR_MAJOR 115 /* 0 to 7 */ -#define TIPAR_MINOR 0 - -#define TISER_MAJOR 115 /* 8 to 15 */ -#define TISER_MINOR 8 - -#define TIUSB_MAJOR 115 /* 16 to 31 */ -#define TIUSB_MINOR 16 - -/* - * Request values for the 'ioctl' function. - */ -#define IOCTL_TIPAR_DELAY _IOW('p', 0xa8, int) /* set delay */ -#define IOCTL_TIPAR_TIMEOUT _IOW('p', 0xa9, int) /* set timeout */ - -#define IOCTL_TISER_DELAY _IOW('p', 0xa0, int) /* set delay */ -#define IOCTL_TISER_TIMEOUT _IOW('p', 0xa1, int) /* set timeout */ - -#define IOCTL_TIUSB_TIMEOUT _IOW('N', 0x20, int) /* set timeout */ -#define IOCTL_TIUSB_RESET_DEVICE _IOW('N', 0x21, int) /* reset device */ -#define IOCTL_TIUSB_RESET_PIPES _IOW('N', 0x22, int) /* reset both pipes*/ -#define IOCTL_TIUSB_GET_MAXPS _IOR('N', 0x23, int) /* max packet size */ -#define IOCTL_TIUSB_GET_DEVID _IOR('N', 0x24, int) /* get device type */ - -#endif /* TICABLE_H */ -- 1.5.3.7 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/