TI J7200 has the Cadence OSPI controller for interfacing with OSPI flashes. Add its node to allow using SPI flashes.
Signed-off-by: Pratyush Yadav <[email protected]> --- .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 17 +++++++++ arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 36 +++++++++++++++++++ 2 files changed, 53 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi index 359e3e8a8cd0..5408ec815d58 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi @@ -269,6 +269,23 @@ hbmc: hyperbus@47034000 { #size-cells = <1>; mux-controls = <&hbmc_mux 0>; }; + + ospi0: spi@47040000 { + compatible = "ti,am654-ospi"; + reg = <0x0 0x47040000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 103 0>; + assigned-clocks = <&k3_clks 103 0>; + assigned-clock-parents = <&k3_clks 103 2>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; }; tscadc0: tscadc@40200000 { diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi index a988e2ab2ba1..effecf852139 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -100,6 +100,22 @@ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ >; }; + + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */ + J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */ + J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */ + J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */ + J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */ + J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */ + J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */ + J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */ + J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */ + J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */ + J721E_WKUP_IOPAD(0x0008, PIN_INPUT_PULLDOWN, 0) /* MCU_OSPI0_DQS */ + >; + }; }; &main_pmx0 { @@ -235,3 +251,23 @@ exp_som: gpio@21 { "GPIO_LIN_EN", "CAN_STB"; }; }; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; -- 2.30.0
