From: dillon min <dillon.min...@gmail.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add dts binding usart3 for bt, uart4 for console
usart3/uart4 pinctrl in stm32h7-pinctrl.dtsi
usart3/uart4 register in stm32h743.dtsi
- add dts binding sdmmc2 for wifi
sdmmc2 pinctrl in stm32h7-pinctrl.dtsi
sdmmc2 register in stm32h743.dtsi
- add spi1 pinctrl in stm32h7-pinctrl.dtsi for spi flash
- add stm32h750-art-pi.dts to support art-pi board
- move pinctrl: pin-controller{} from stm32h7-pinctrl.dtsi to stm32h743.dtsi
to fix dtbs_check warrning
- change 'i2c4: i2c@58001C00' to 'i2c4: i2c@58001c00', else will get
dtbs_check warrning:
>> arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes:
'@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
...
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Fixes: 500cdb23d608 ("ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL
board")
Signed-off-by: dillon min <dillon.min...@gmail.com>
Reported-by: kernel test robot <l...@intel.com>
---
v3:
- move pinctrl: pin-controller{} from stm32h7-pinctrl.dtsi to stm32h743.dtsi
to fix dtbs_check warrning
>> arch/arm/boot/dts/stm32h743i-eval.dt.yaml: soc: pin-controller: {'type':
'object'} is not allowed for {'#address-cells': [[1]], '#size-cells':
[[1]], 'ranges': [[0,
- fix dtbs_check warrning:
arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes:
'@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
v2:
- fix author name/copyright mistake
- make item in stm32h750i-art-pi.dts sort by letter
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/stm32h743.dtsi | 153 ++++++++++++++++++++-
arch/arm/boot/dts/stm32h750.dtsi | 5 +
arch/arm/boot/dts/stm32h750i-art-pi.dts | 228 ++++++++++++++++++++++++++++++++
4 files changed, 385 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8e5d4ab4e75e..a19c5ab9df84 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1071,6 +1071,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32746g-eval.dtb \
stm32h743i-eval.dtb \
stm32h743i-disco.dtb \
+ stm32h750i-art-pi.dtb \
stm32mp153c-dhcom-drc02.dtb \
stm32mp157a-avenger96.dtb \
stm32mp157a-dhcor-avenger96.dtb \
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 4ebffb0a45a3..4379063d36a2 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -135,6 +135,22 @@
clocks = <&rcc USART2_CK>;
};
+ usart3: serial@40004800 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40004800 0x400>;
+ interrupts = <39>;
+ status = "disabled";
+ clocks = <&rcc USART3_CK>;
+ };
+
+ uart4: serial@40004c00 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40004c00 0x400>;
+ interrupts = <52>;
+ status = "disabled";
+ clocks = <&rcc UART4_CK>;
+ };
+
i2c1: i2c@40005400 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
@@ -159,7 +175,7 @@
status = "disabled";
};
- i2c3: i2c@40005C00 {
+ i2c3: i2c@40005c00 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
#size-cells = <0>;
@@ -368,6 +384,20 @@
max-frequency = <120000000>;
};
+ sdmmc2: mmc@48022400 {
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x10153180>;
+ reg = <0x48022400 0x400>;
+ interrupts = <124>;
+ interrupt-names = "cmd_irq";
+ clocks = <&rcc SDMMC2_CK>;
+ clock-names = "apb_pclk";
+ resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ };
+
exti: interrupt-controller@58000000 {
compatible = "st,stm32h7-exti";
interrupt-controller;
@@ -392,7 +422,7 @@
status = "disabled";
};
- i2c4: i2c@58001C00 {
+ i2c4: i2c@58001c00 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
#size-cells = <0>;
@@ -555,6 +585,125 @@
snps,pbl = <8>;
status = "disabled";
};
+
+ pinctrl: pin-controller@58020000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x58020000 0x3000>;
+ interrupt-parent = <&exti>;
+ st,syscfg = <&syscfg 0x8>;
+ pins-are-numbered;
+
+ gpioa: gpio@58020000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x0 0x400>;
+ clocks = <&rcc GPIOA_CK>;
+ st,bank-name = "GPIOA";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiob: gpio@58020400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x400 0x400>;
+ clocks = <&rcc GPIOB_CK>;
+ st,bank-name = "GPIOB";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioc: gpio@58020800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x800 0x400>;
+ clocks = <&rcc GPIOC_CK>;
+ st,bank-name = "GPIOC";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiod: gpio@58020c00 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0xc00 0x400>;
+ clocks = <&rcc GPIOD_CK>;
+ st,bank-name = "GPIOD";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioe: gpio@58021000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1000 0x400>;
+ clocks = <&rcc GPIOE_CK>;
+ st,bank-name = "GPIOE";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiof: gpio@58021400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1400 0x400>;
+ clocks = <&rcc GPIOF_CK>;
+ st,bank-name = "GPIOF";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiog: gpio@58021800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1800 0x400>;
+ clocks = <&rcc GPIOG_CK>;
+ st,bank-name = "GPIOG";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioh: gpio@58021c00 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1c00 0x400>;
+ clocks = <&rcc GPIOH_CK>;
+ st,bank-name = "GPIOH";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioi: gpio@58022000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2000 0x400>;
+ clocks = <&rcc GPIOI_CK>;
+ st,bank-name = "GPIOI";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioj: gpio@58022400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2400 0x400>;
+ clocks = <&rcc GPIOJ_CK>;
+ st,bank-name = "GPIOJ";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiok: gpio@58022800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2800 0x400>;
+ clocks = <&rcc GPIOK_CK>;
+ st,bank-name = "GPIOK";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
new file mode 100644
index 000000000000..dd9166223c2f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750.dtsi
@@ -0,0 +1,5 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
+
+#include "stm32h743.dtsi"
+
diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts
b/arch/arm/boot/dts/stm32h750i-art-pi.dts
new file mode 100644
index 000000000000..87f1cbedfda5
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
@@ -0,0 +1,228 @@
+/*
+ * Copyright 2021 - Dillon Min <dillon.min...@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * For art-pi board resources, you can refer to link:
+ * https://art-pi.gitee.io/website/
+ */
+
+/dts-v1/;
+#include "stm32h750.dtsi"
+#include "stm32h750-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "RT-Thread STM32H750i-ART-PI board";
+ compatible = "st,stm32h750i-art-pi", "st,stm32h750";
+
+ chosen {
+ bootargs = "root=/dev/ram";
+ stdout-path = "serial0:2000000n8";
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x2000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ no-map;
+ size = <0x100000>;
+ linux,dma-default;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ serial1 = &usart3;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-red {
+ gpios = <&gpioi 8 0>;
+ };
+ led-green {
+ gpios = <&gpioc 15 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ v3v3: regulator-v3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ wlan_pwr: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&clk_hse {
+ clock-frequency = <25000000>;
+};
+
+&dma1 {
+ status = "okay";
+};
+
+&dma2 {
+ status = "okay";
+};
+
+&mac {
+ status = "disabled";
+ pinctrl-0 = <ðernet_rmii>;
+ pinctrl-names = "default";
+ phy-mode = "rmii";
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+ broken-cd;
+ non-removable;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&wlan_pwr>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
+ dmas = <&dmamux1 37 0x400 0x05>,
+ <&dmamux1 38 0x400 0x05>;
+ dma-names = "rx", "tx";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+
+ partition@0 {
+ label = "root filesystem";
+ reg = <0 0x1000000>;
+ };
+ };
+};
+
+&usart2 {
+ pinctrl-0 = <&usart2_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+};
+
+&usart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usart3_pins>;
+ dmas = <&dmamux1 45 0x400 0x05>,
+ <&dmamux1 46 0x400 0x05>;
+ dma-names = "rx", "tx";
+ st,hw-flow-ctrl;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+ max-speed = <115200>;
+ };
+};
+
+&uart4 {
+ pinctrl-0 = <&uart4_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
--
1.9.1
