> I have checked in Snowball schematics and I can confirm that the fixed
> 3.3V regulator is GPIO26 on AB8500 not DB8500, so its numero is
> MOP500_AB8500_PIN_GPIO(26)
We're also using GPIO26 on the DB8500 in the Device Tree solution.
Odd that is should work? I wonder if we're just getting lucky, or if
it's just not required?
> and you have first to update the upstream gpio-ab8500 driver.
I see. Do you know what needs to be updated to get it working?
> On 08/24/2012 02:48 PM, Lee Jones wrote:
> > The SMSC911x Ethernet chip requires a fixed-regulator in order to
> > function correctly. We have previously provided a means to obtain
> > this during a Device Tree boot, however nothing has been put into
> > place when booting with a non-DT kernel. This patch aims to change
> > that.
> >
> > Signed-off-by: Lee Jones <lee.jo...@linaro.org>
> > ---
> > arch/arm/mach-ux500/board-mop500-regulators.c | 17 +++++++++++++++++
> > arch/arm/mach-ux500/board-mop500-regulators.h | 1 +
> > arch/arm/mach-ux500/board-mop500.c | 21 +++++++++++++++++++++
> > arch/arm/mach-ux500/board-mop500.h | 2 +-
> > 4 files changed, 40 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c
> > b/arch/arm/mach-ux500/board-mop500-regulators.c
> > index 52426a4..139f31e 100644
> > --- a/arch/arm/mach-ux500/board-mop500-regulators.c
> > +++ b/arch/arm/mach-ux500/board-mop500-regulators.c
> > @@ -13,6 +13,23 @@
> > #include <linux/regulator/ab8500.h>
> > #include "board-mop500-regulators.h"
> >
> > +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE
> > +static struct regulator_consumer_supply gpio_en_3v3_consumers[] = {
> > + REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
> > +};
> > +
> > +struct regulator_init_data gpio_en_3v3_regulator = {
> > + .constraints = {
> > + .name = "EN-3V3",
> > + .min_uV = 3300000,
> > + .max_uV = 3300000,
> > + .valid_ops_mask = REGULATOR_CHANGE_STATUS,
> > + },
> > + .num_consumer_supplies = ARRAY_SIZE(gpio_en_3v3_consumers),
> > + .consumer_supplies = gpio_en_3v3_consumers,
> > +};
> > +#endif
> > +
> > /*
> > * TPS61052 regulator
> > */
> > diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h
> > b/arch/arm/mach-ux500/board-mop500-regulators.h
> > index 9499215..78a0642 100644
> > --- a/arch/arm/mach-ux500/board-mop500-regulators.h
> > +++ b/arch/arm/mach-ux500/board-mop500-regulators.h
> > @@ -18,5 +18,6 @@ extern struct ab8500_regulator_reg_init
> > ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS];
> > extern struct regulator_init_data
> > ab8500_regulators[AB8500_NUM_REGULATORS];
> > extern struct regulator_init_data tps61052_regulator;
> > +extern struct regulator_init_data gpio_en_3v3_regulator;
> >
> > #endif
> > diff --git a/arch/arm/mach-ux500/board-mop500.c
> > b/arch/arm/mach-ux500/board-mop500.c
> > index 42e1759..c7f0973 100644
> > --- a/arch/arm/mach-ux500/board-mop500.c
> > +++ b/arch/arm/mach-ux500/board-mop500.c
> > @@ -23,6 +23,7 @@
> > #include <linux/spi/spi.h>
> > #include <linux/mfd/abx500/ab8500.h>
> > #include <linux/regulator/ab8500.h>
> > +#include <linux/regulator/fixed.h>
> > #include <linux/mfd/tc3589x.h>
> > #include <linux/mfd/tps6105x.h>
> > #include <linux/mfd/abx500/ab8500-gpio.h>
> > @@ -75,6 +76,25 @@ static struct platform_device snowball_led_dev = {
> > },
> > };
> >
> > +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE
> > +static struct fixed_voltage_config snowball_gpio_en_3v3_data = {
> > + .supply_name = "EN-3V3",
> > + .gpio = SNOWBALL_EN_3V3_ETH_GPIO,
> > + .microvolts = 3300000,
> > + .enable_high = 1,
> > + .init_data = &gpio_en_3v3_regulator,
> > + .startup_delay = 5000, /* 1200us */
> > +};
> > +
> > +static struct platform_device snowball_gpio_en_3v3_regulator_dev = {
> > + .name = "reg-fixed-voltage",
> > + .id = 1,
> > + .dev = {
> > + .platform_data = &snowball_gpio_en_3v3_data,
> > + },
> > +};
> > +#endif
> > +
> > static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
> > .gpio_base = MOP500_AB8500_PIN_GPIO(1),
> > .irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE,
> > @@ -585,6 +605,7 @@ static struct platform_device *snowball_platform_devs[]
> > __initdata = {
> > &snowball_led_dev,
> > &snowball_key_dev,
> > &snowball_sbnet_dev,
> > + &snowball_gpio_en_3v3_regulator_dev,
> > };
> >
> > static void __init mop500_init_machine(void)
> > diff --git a/arch/arm/mach-ux500/board-mop500.h
> > b/arch/arm/mach-ux500/board-mop500.h
> > index 9e9dd5a..d3a02d5 100644
> > --- a/arch/arm/mach-ux500/board-mop500.h
> > +++ b/arch/arm/mach-ux500/board-mop500.h
> > @@ -13,6 +13,7 @@
> > #include <linux/amba/mmci.h>
> >
> > /* Snowball specific GPIO assignments, this board has no GPIO expander */
> > +#define SNOWBALL_EN_3V3_ETH_GPIO 26
> No it's MOP500_AB8500_PIN_GPIO(26)
> > #define SNOWBALL_ACCEL_INT1_GPIO 163
> > #define SNOWBALL_ACCEL_INT2_GPIO 164
> > #define SNOWBALL_MAGNET_DRDY_GPIO 165
> > @@ -76,7 +77,6 @@
> > #define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4)
> > /* SYSCLKREQ6/GPIO4 */
> > #define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16)
> > /* PWMOUT3/GPIO16 */
> > #define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24)
> > /* SYSCLKREQ7/GPIO24 */
> > -#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /*
> > GPIO26 */
> keep this line
> >
> > struct device;
> > struct i2c_board_info;
--
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
