On Thu, Apr 18, 2013 at 11:11:44AM +0100, Lee Jones wrote:
> There are only two default memcpy configurations used for the DMA40
> driver; one for physical memcpy and one for logical memcpy. Instead
> of invariably passing the same configurations though platform data,
> we're moving them into the driver instead.
>
> Cc: Vinod Koul <vinod.k...@intel.com>
> Cc: Dan Williams <d...@fb.com>
> Cc: Per Forlin <per.for...@stericsson.com>
> Cc: Rabin Vincent <ra...@rab.in>
> Acked-by: Arnd Bergmann <a...@arndb.de>
> Signed-off-by: Lee Jones <lee.jo...@linaro.org>
Acked-by: Vinod Koul <vnod.k...@intel.com>
--
~Vinod
> ---
> arch/arm/mach-ux500/devices-db8500.c | 28 -----------------------
> drivers/dma/ste_dma40.c | 32
> +++++++++++++++++++++++++--
> include/linux/platform_data/dma-ste-dma40.h | 4 ----
> 3 files changed, 30 insertions(+), 34 deletions(-)
>
> diff --git a/arch/arm/mach-ux500/devices-db8500.c
> b/arch/arm/mach-ux500/devices-db8500.c
> index 9b09683..5b1f1f7 100644
> --- a/arch/arm/mach-ux500/devices-db8500.c
> +++ b/arch/arm/mach-ux500/devices-db8500.c
> @@ -42,32 +42,6 @@ static struct resource dma40_resources[] = {
> }
> };
>
> -/* Default configuration for physcial memcpy */
> -struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
> - .mode = STEDMA40_MODE_PHYSICAL,
> - .dir = STEDMA40_MEM_TO_MEM,
> -
> - .src_info.data_width = STEDMA40_BYTE_WIDTH,
> - .src_info.psize = STEDMA40_PSIZE_PHY_1,
> - .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> -
> - .dst_info.data_width = STEDMA40_BYTE_WIDTH,
> - .dst_info.psize = STEDMA40_PSIZE_PHY_1,
> - .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> -};
> -/* Default configuration for logical memcpy */
> -struct stedma40_chan_cfg dma40_memcpy_conf_log = {
> - .dir = STEDMA40_MEM_TO_MEM,
> -
> - .src_info.data_width = STEDMA40_BYTE_WIDTH,
> - .src_info.psize = STEDMA40_PSIZE_LOG_1,
> - .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> -
> - .dst_info.data_width = STEDMA40_BYTE_WIDTH,
> - .dst_info.psize = STEDMA40_PSIZE_LOG_1,
> - .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> -};
> -
> /*
> * Mapping between destination event lines and physical device address.
> * The event line is tied to a device and therefore the address is constant.
> @@ -150,8 +124,6 @@ static struct stedma40_platform_data dma40_plat_data = {
> .dev_len = DB8500_DMA_NR_DEV,
> .dev_rx = dma40_rx_map,
> .dev_tx = dma40_tx_map,
> - .memcpy_conf_phy = &dma40_memcpy_conf_phy,
> - .memcpy_conf_log = &dma40_memcpy_conf_log,
> .disabled_channels = {-1},
> };
>
> diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
> index 12de79e..3b83dee 100644
> --- a/drivers/dma/ste_dma40.c
> +++ b/drivers/dma/ste_dma40.c
> @@ -58,6 +58,34 @@
> /* Reserved event lines for memcpy only. */
> static int dma40_memcpy_channels[] = { 56, 57, 58, 59, 60 };
>
> +/* Default configuration for physcial memcpy */
> +struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
> + .mode = STEDMA40_MODE_PHYSICAL,
> + .dir = STEDMA40_MEM_TO_MEM,
> +
> + .src_info.data_width = STEDMA40_BYTE_WIDTH,
> + .src_info.psize = STEDMA40_PSIZE_PHY_1,
> + .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> +
> + .dst_info.data_width = STEDMA40_BYTE_WIDTH,
> + .dst_info.psize = STEDMA40_PSIZE_PHY_1,
> + .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> +};
> +
> +/* Default configuration for logical memcpy */
> +struct stedma40_chan_cfg dma40_memcpy_conf_log = {
> + .mode = STEDMA40_MODE_LOGICAL,
> + .dir = STEDMA40_MEM_TO_MEM,
> +
> + .src_info.data_width = STEDMA40_BYTE_WIDTH,
> + .src_info.psize = STEDMA40_PSIZE_LOG_1,
> + .src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> +
> + .dst_info.data_width = STEDMA40_BYTE_WIDTH,
> + .dst_info.psize = STEDMA40_PSIZE_LOG_1,
> + .dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
> +};
> +
> /**
> * enum 40_command - The different commands and/or statuses.
> *
> @@ -2015,13 +2043,13 @@ static int d40_config_memcpy(struct d40_chan *d40c)
> dma_cap_mask_t cap = d40c->chan.device->cap_mask;
>
> if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
> - d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_log;
> + d40c->dma_cfg = dma40_memcpy_conf_log;
> d40c->dma_cfg.src_dev_type = STEDMA40_DEV_SRC_MEMORY;
> d40c->dma_cfg.dst_dev_type =
> dma40_memcpy_channels[d40c->chan.chan_id];
>
> } else if (dma_has_cap(DMA_MEMCPY, cap) &&
> dma_has_cap(DMA_SLAVE, cap)) {
> - d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_phy;
> + d40c->dma_cfg = dma40_memcpy_conf_phy;
> } else {
> chan_err(d40c, "No memcpy\n");
> return -EINVAL;
> diff --git a/include/linux/platform_data/dma-ste-dma40.h
> b/include/linux/platform_data/dma-ste-dma40.h
> index a808784..869c571 100644
> --- a/include/linux/platform_data/dma-ste-dma40.h
> +++ b/include/linux/platform_data/dma-ste-dma40.h
> @@ -141,8 +141,6 @@ struct stedma40_chan_cfg {
> * @dev_len: length of dev_tx and dev_rx
> * @dev_tx: mapping between destination event line and io address
> * @dev_rx: mapping between source event line and io address
> - * @memcpy_conf_phy: default configuration of physical channel memcpy
> - * @memcpy_conf_log: default configuration of logical channel memcpy
> * @disabled_channels: A vector, ending with -1, that marks physical channels
> * that are for different reasons not available for the driver.
> * @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
> @@ -160,8 +158,6 @@ struct stedma40_platform_data {
> u32 dev_len;
> const dma_addr_t *dev_tx;
> const dma_addr_t *dev_rx;
> - struct stedma40_chan_cfg *memcpy_conf_phy;
> - struct stedma40_chan_cfg *memcpy_conf_log;
> int disabled_channels[STEDMA40_MAX_PHYS];
> int *soft_lli_chans;
> int num_of_soft_lli_chans;
> --
> 1.7.10.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
