On Fri, 11 Mar 2005, Bjorn Helgaas wrote:
On Fri, 2005-03-11 at 20:36 +0100, Grzegorz Kulewski wrote:On Fri, 11 Mar 2005, Bjorn Helgaas wrote:Can you check to see whether there are any BIOS updates available for your box? It looks to me like your USB controllers are wired to IRQ9, and that's how the BIOS is leaving them configured.
And if this is a BIOS issue then why it worked for 3 years with all kernels up to at least 2.6.9
Good point.
Thanks for posting the 2.6.9 output as well. It contains this:
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 10 (level, low) -> IRQ 10 PCI: Via IRQ fixup for 0000:00:07.2, from 9 to 10 PCI: Via IRQ fixup for 0000:00:07.3, from 9 to 10
In 2.6.9, we did all the ACPI IRQ routing early, then did the Via IRQ fixups. In 2.6.11, ACPI IRQ routing is done only when a driver claims a device, and the Via IRQ fixup is done a little differently. In fact, the Via fixup happens before we twiddle the IOAPIC, where in 2.6.9, it happened after.
Can you try the attached patch to see whether it makes any difference?
===== drivers/acpi/pci_irq.c 1.37 vs edited ===== --- 1.37/drivers/acpi/pci_irq.c 2005-03-01 09:57:29 -07:00 +++ edited/drivers/acpi/pci_irq.c 2005-03-11 13:45:56 -07:00 @@ -30,6 +30,7 @@ #include <linux/module.h> #include <linux/init.h> #include <linux/types.h> +#include <linux/delay.h> #include <linux/proc_fs.h> #include <linux/spinlock.h> #include <linux/pm.h> @@ -438,10 +439,19 @@ } }
- if (via_interrupt_line_quirk) - pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq & 15); - dev->irq = acpi_register_gsi(irq, edge_level, active_high_low); + + if (via_interrupt_line_quirk) { + u8 old_irq, new_irq = dev->irq & 0xf; + + pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &old_irq); + if (new_irq != old_irq) { + printk(KERN_INFO PREFIX "Via IRQ fixup for %s, from %d " + "to %d\n", pci_name(dev), old_irq, new_irq); + udelay(15); + pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); + } + }
printk(KERN_INFO PREFIX "PCI interrupt %s[%c] -> GSI %u " "(%s, %s) -> IRQ %d\n",
Unfortunatelly no. Here is the log:
Mar 11 23:47:44 kangur Linux version 2.6.11-cko1 ([EMAIL PROTECTED]) (gcc version 3.3.3 20040412 (Gentoo Linux 3.3.3-r6, ssp-3.3.2-2, pie-8.7.6)) #2 Fri Mar 11 23:32:57 CET 2005
Mar 11 23:47:44 kangur BIOS-provided physical RAM map:
Mar 11 23:47:44 kangur BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Mar 11 23:47:44 kangur BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Mar 11 23:47:44 kangur BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Mar 11 23:47:44 kangur BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
Mar 11 23:47:44 kangur BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
Mar 11 23:47:44 kangur BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
Mar 11 23:47:44 kangur BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Mar 11 23:47:44 kangur 511MB LOWMEM available.
Mar 11 23:47:44 kangur On node 0 totalpages: 131056
Mar 11 23:47:44 kangur DMA zone: 4096 pages, LIFO batch:1
Mar 11 23:47:44 kangur Normal zone: 126960 pages, LIFO batch:16
Mar 11 23:47:44 kangur HighMem zone: 0 pages, LIFO batch:1
Mar 11 23:47:44 kangur DMI 2.2 present.
Mar 11 23:47:44 kangur ACPI: RSDP (v000 761686 ) @ 0x000f6a70
Mar 11 23:47:44 kangur ACPI: RSDT (v001 761686 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
Mar 11 23:47:44 kangur ACPI: FADT (v001 761686 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
Mar 11 23:47:44 kangur ACPI: DSDT (v001 761686 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
Mar 11 23:47:44 kangur ACPI: PM-Timer IO Port: 0x4008
Mar 11 23:47:44 kangur Allocating PCI resources starting at 20000000 (gap: 20000000:dfff0000)
Mar 11 23:47:44 kangur Built 1 zonelists
Mar 11 23:47:44 kangur Kernel command line: ro root=/dev/hdb4
Mar 11 23:47:44 kangur Local APIC disabled by BIOS -- you can enable it with "lapic"
Mar 11 23:47:44 kangur mapped APIC to ffffd000 (01402000)
Mar 11 23:47:44 kangur Initializing CPU#0
Mar 11 23:47:44 kangur CPU 0 irqstacks, hard=b0477000 soft=b0476000
Mar 11 23:47:44 kangur PID hash table entries: 2048 (order: 11, 32768 bytes)
Mar 11 23:47:44 kangur Detected 1203.228 MHz processor.
Mar 11 23:47:44 kangur Using pmtmr for high-res timesource
Mar 11 23:47:44 kangur Console: colour VGA+ 80x25
Mar 11 23:47:44 kangur Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Mar 11 23:47:44 kangur Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mar 11 23:47:44 kangur Memory: 514940k/524224k available (2543k kernel code, 8732k reserved, 819k data, 156k init, 0k highmem)
Mar 11 23:47:44 kangur Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mar 11 23:47:44 kangur Calibrating delay loop... 2375.68 BogoMIPS (lpj=1187840)
Mar 11 23:47:44 kangur Security Framework v1.0.0 initialized
Mar 11 23:47:44 kangur Capability LSM initialized
Mar 11 23:47:44 kangur Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Mar 11 23:47:44 kangur CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000Mar 11 23:47:44 kangur CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
Mar 11 23:47:44 kangur CPU: CLK_CTL MSR was 60071263. Reprogramming to 20071263
Mar 11 23:47:44 kangur CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Mar 11 23:47:44 kangur CPU: L2 Cache: 512K (64 bytes/line)
Mar 11 23:47:44 kangur CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 00000000 00000000 00000000
Mar 11 23:47:44 kangur Intel machine check architecture supported.
Mar 11 23:47:44 kangur Intel machine check reporting enabled on CPU#0.
Mar 11 23:47:44 kangur CPU: AMD Unknown CPU Type stepping 00
Mar 11 23:47:44 kangur Enabling fast FPU save and restore... done.
Mar 11 23:47:44 kangur Enabling unmasked SIMD FPU exception support... done.
Mar 11 23:47:44 kangur Checking 'hlt' instruction... OK.
Mar 11 23:47:44 kangur ACPI: setting ELCR to 0800 (from 0e20)
Mar 11 23:47:44 kangur NET: Registered protocol family 16
Mar 11 23:47:44 kangur PCI: PCI BIOS revision 2.10 entry at 0xfb690, last bus=1
Mar 11 23:47:44 kangur PCI: Using configuration type 1
Mar 11 23:47:44 kangur mtrr: v2.0 (20020519)
Mar 11 23:47:44 kangur ACPI: Subsystem revision 20050211
Mar 11 23:47:44 kangur ACPI: Interpreter enabled
Mar 11 23:47:44 kangur ACPI: Using PIC for interrupt routing
Mar 11 23:47:44 kangur ACPI: PCI Root Bridge [PCI0] (00:00)
Mar 11 23:47:44 kangur PCI: Probing PCI hardware (bus 00)
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
Mar 11 23:47:44 kangur Linux Plug and Play Support v0.97 (c) Adam Belay
Mar 11 23:47:44 kangur pnp: PnP ACPI init
Mar 11 23:47:44 kangur pnp: PnP ACPI: found 12 devices
Mar 11 23:47:44 kangur SCSI subsystem initialized
Mar 11 23:47:44 kangur PCI: Using ACPI for IRQ routing
Mar 11 23:47:44 kangur ** PCI interrupts are no longer routed automatically. If this
Mar 11 23:47:44 kangur ** causes a device to stop working, it is probably because the
Mar 11 23:47:44 kangur ** driver failed to call pci_enable_device(). As a temporary
Mar 11 23:47:44 kangur ** workaround, the "pci=routeirq" argument restores the old
Mar 11 23:47:44 kangur ** behavior. If this argument makes the device work again,
Mar 11 23:47:44 kangur ** please email the output of "lspci" to [EMAIL PROTECTED]
Mar 11 23:47:44 kangur ** so I can fix the driver.
Mar 11 23:47:44 kangur pnp: the driver 'system' has been registered
Mar 11 23:47:44 kangur pnp: match found with the PnP device '00:00' and the driver 'system'
Mar 11 23:47:44 kangur pnp: match found with the PnP device '00:01' and the driver 'system'
Mar 11 23:47:44 kangur Total HugeTLB memory allocated, 0
Mar 11 23:47:44 kangur VFS: Disk quotas dquot_6.5.1
Mar 11 23:47:44 kangur Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Mar 11 23:47:44 kangur SGI XFS with ACLs, security attributes, realtime, no debug enabled
Mar 11 23:47:44 kangur SGI XFS Quota Management subsystem
Mar 11 23:47:44 kangur Initializing Cryptographic API
Mar 11 23:47:44 kangur inotify device minor=63
Mar 11 23:47:44 kangur ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
Mar 11 23:47:44 kangur ACPI: PS/2 Mouse Controller [PS2M] at irq 12
Mar 11 23:47:44 kangur serio: i8042 AUX port at 0x60,0x64 irq 12
Mar 11 23:47:44 kangur serio: i8042 KBD port at 0x60,0x64 irq 1
Mar 11 23:47:44 kangur io scheduler noop registered
Mar 11 23:47:44 kangur io scheduler anticipatory registered
Mar 11 23:47:44 kangur io scheduler deadline registered
Mar 11 23:47:44 kangur io scheduler cfq registered
Mar 11 23:47:44 kangur 8139too Fast Ethernet driver 0.9.27
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
Mar 11 23:47:44 kangur PCI: setting IRQ 11 as level-triggered
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 11 (level, low) -> IRQ 11
Mar 11 23:47:44 kangur eth0: RealTek RTL8139 at 0xec00, 00:06:4f:00:73:8b, IRQ 11
Mar 11 23:47:44 kangur eth0: Identified 8139 chip type 'RTL-8139C'
Mar 11 23:47:44 kangur Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Mar 11 23:47:44 kangur ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 11 23:47:44 kangur VP_IDE: IDE controller at PCI slot 0000:00:07.1
Mar 11 23:47:44 kangur VP_IDE: chipset revision 6
Mar 11 23:47:44 kangur VP_IDE: not 100% native mode: will probe irqs later
Mar 11 23:47:44 kangur VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
Mar 11 23:47:44 kangur ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:pio, hdb:DMA
Mar 11 23:47:44 kangur ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:pio, hdd:DMA
Mar 11 23:47:44 kangur Probing IDE interface ide0...
Mar 11 23:47:44 kangur hdb: SAMSUNG SV3063H, ATA DISK drive
Mar 11 23:47:44 kangur ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Mar 11 23:47:44 kangur Probing IDE interface ide1...
Mar 11 23:47:44 kangur hdd: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM drive
Mar 11 23:47:44 kangur ide1 at 0x170-0x177,0x376 on irq 15
Mar 11 23:47:44 kangur pnp: the driver 'ide' has been registered
Mar 11 23:47:44 kangur hdb: max request size: 128KiB
Mar 11 23:47:44 kangur hdb: 59797584 sectors (30616 MB) w/426KiB Cache, CHS=59323/16/63, UDMA(100)
Mar 11 23:47:44 kangur hdb: cache flushes not supported
Mar 11 23:47:44 kangur hdb: hdb1 hdb2 hdb3 hdb4
Mar 11 23:47:44 kangur libata version 1.10 loaded.
Mar 11 23:47:44 kangur sata_sil version 0.8
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
Mar 11 23:47:44 kangur ata1: SATA max UDMA/100 cmd 0xD0802080 ctl 0xD080208A bmdma 0xD0802000 irq 11
Mar 11 23:47:44 kangur ata2: SATA max UDMA/100 cmd 0xD08020C0 ctl 0xD08020CA bmdma 0xD0802008 irq 11
Mar 11 23:47:44 kangur ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003 88:207f
Mar 11 23:47:44 kangur ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
Mar 11 23:47:44 kangur ata1: dev 0 configured for UDMA/100
Mar 11 23:47:44 kangur scsi0 : sata_sil
Mar 11 23:47:44 kangur ata2: no device found (phy stat 00000000)
Mar 11 23:47:44 kangur scsi1 : sata_sil
Mar 11 23:47:44 kangur Vendor: ATA Model: WDC WD1600JD-00H Rev: 08.0
Mar 11 23:47:44 kangur Type: Direct-Access ANSI SCSI revision: 05
Mar 11 23:47:44 kangur SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
Mar 11 23:47:44 kangur SCSI device sda: drive cache: write back
Mar 11 23:47:44 kangur SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
Mar 11 23:47:44 kangur SCSI device sda: drive cache: write back
Mar 11 23:47:44 kangur sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >
Mar 11 23:47:44 kangur Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Mar 11 23:47:44 kangur mice: PS/2 mouse device common for all mice
Mar 11 23:47:44 kangur input: AT Translated Set 2 keyboard on isa0060/serio0
Mar 11 23:47:44 kangur NET: Registered protocol family 2
Mar 11 23:47:44 kangur IP: routing cache hash table of 4096 buckets, 32Kbytes
Mar 11 23:47:44 kangur TCP established hash table entries: 32768 (order: 6, 262144 bytes)
Mar 11 23:47:44 kangur TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
Mar 11 23:47:44 kangur TCP: Hash tables configured (established 32768 bind 32768)
Mar 11 23:47:44 kangur ip_conntrack version 2.1 (4095 buckets, 32760 max) - 216 bytes per conntrack
Mar 11 23:47:44 kangur ip_tables: (C) 2000-2002 Netfilter core team
Mar 11 23:47:44 kangur ipt_recent v0.3.1: Stephen Frost <[EMAIL PROTECTED]>. http://snowman.net/projects/ipt_recent/
Mar 11 23:47:44 kangur arp_tables: (C) 2002 David S. Miller
Mar 11 23:47:44 kangur NET: Registered protocol family 17
Mar 11 23:47:44 kangur ACPI wakeup devices:
Mar 11 23:47:44 kangur SLPB PCI0 USB0 USB1
Mar 11 23:47:44 kangur ACPI: (supports S0 S1 S4 S5)
Mar 11 23:47:44 kangur kjournald starting. Commit interval 5 seconds
Mar 11 23:47:44 kangur EXT3-fs: mounted filesystem with ordered data mode.
Mar 11 23:47:44 kangur VFS: Mounted root (ext3 filesystem) readonly.
Mar 11 23:47:44 kangur Freeing unused kernel memory: 156k freed
Mar 11 23:47:44 kangur NET: Registered protocol family 1
Mar 11 23:47:44 kangur EXT3 FS on hdb4, internal journal
Mar 11 23:47:44 kangur NET: Registered protocol family 8
Mar 11 23:47:44 kangur NET: Registered protocol family 20
Mar 11 23:47:44 kangur CSLIP: code copyright 1989 Regents of the University of California
Mar 11 23:47:44 kangur PPP generic driver version 2.4.2
Mar 11 23:47:44 kangur input: PS/2 Generic Mouse on isa0060/serio1
Mar 11 23:47:44 kangur input: PC Speaker
Mar 11 23:47:44 kangur loop: loaded (max 8 devices)
Mar 11 23:47:44 kangur Non-volatile memory driver v1.2
Mar 11 23:47:44 kangur BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Mar 11 23:47:44 kangur vesafb: NVidia Corporation, NV15 Reference Board, Chip Rev A0 (OEM: NVidia)
Mar 11 23:47:44 kangur vesafb: VBE version: 3.0
Mar 11 23:47:44 kangur vesafb: protected mode interface info at c000:0f03
Mar 11 23:47:44 kangur vesafb: pmi: set display start = b00c0f3c, set palette = b00c0fb2
Mar 11 23:47:44 kangur vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
Mar 11 23:47:44 kangur vesafb: hardware supports DCC2 transfers
Mar 11 23:47:44 kangur vesafb: monitor limits: vf = 85 Hz, hf = 64 kHz, clk = 108 MHz
Mar 11 23:47:44 kangur vesafb: scrolling: redraw
Mar 11 23:47:44 kangur vesafb: framebuffer at 0xe8000000, mapped to 0xd0900000, using 6144k, total 65536k
Mar 11 23:47:44 kangur fb0: VESA VGA frame buffer device
Mar 11 23:47:44 kangur Console: switching to colour frame buffer device 128x48
Mar 11 23:47:44 kangur device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED]
Mar 11 23:47:44 kangur NTFS driver 2.1.22 [Flags: R/O MODULE].
Mar 11 23:47:44 kangur NTFS volume version 3.1.
Mar 11 23:47:44 kangur NTFS volume version 3.1.
Mar 11 23:47:44 kangur usbcore: registered new driver usbfs
Mar 11 23:47:44 kangur usbcore: registered new driver hub
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
Mar 11 23:47:44 kangur PCI: setting IRQ 10 as level-triggered
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 10 (level, low) -> IRQ 10
Mar 11 23:47:44 kangur parport_pc: VIA 686A/8231 detected
Mar 11 23:47:44 kangur parport_pc: probing current configuration
Mar 11 23:47:44 kangur parport_pc: Current parallel port base: 0x378
Mar 11 23:47:44 kangur parport_pc: Strange, can't probe VIA parallel port: io=0x378, irq=7, dma=-1
Mar 11 23:47:44 kangur pnp: the driver 'parport_pc' has been registered
Mar 11 23:47:44 kangur pnp: match found with the PnP device '00:09' and the driver 'parport_pc'
Mar 11 23:47:44 kangur parport: PnPBIOS parport detected.
Mar 11 23:47:44 kangur parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
Mar 11 23:47:44 kangur USB Universal Host Controller Interface driver v2.2
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 10 (level, low) -> IRQ 10
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.2: UHCI Host Controller
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.2: irq 10, io base 0xc800
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
Mar 11 23:47:44 kangur hub 1-0:1.0: USB hub found
Mar 11 23:47:44 kangur hub 1-0:1.0: 2 ports detected
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 10 (level, low) -> IRQ 10
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.3: UHCI Host Controller
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.3: irq 10, io base 0xcc00
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
Mar 11 23:47:44 kangur hub 2-0:1.0: USB hub found
Mar 11 23:47:44 kangur hub 2-0:1.0: 2 ports detected
Mar 11 23:47:44 kangur usb 1-2: new full speed USB device using uhci_hcd and address 2
Mar 11 23:47:44 kangur Linux video capture interface: v1.00
Mar 11 23:47:44 kangur bttv: driver version 0.9.15 loaded
Mar 11 23:47:44 kangur bttv: using 32 buffers with 2080k (520 pages) each for capture
Mar 11 23:47:44 kangur bttv: Bt8xx card found (0).
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
Mar 11 23:47:44 kangur PCI: setting IRQ 5 as level-triggered
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, low) -> IRQ 5
Mar 11 23:47:44 kangur bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 5, latency: 32, mmio: 0xf7000000
Mar 11 23:47:44 kangur bttv0: using: Prolink Pixelview PV-BT878P+ (Rev.4C,8E) [card=70,insmod option]
Mar 11 23:47:44 kangur bttv0: gpio: en=00000000, out=00000000 in=00ffc0ff [init]
Mar 11 23:47:44 kangur bttv0: using tuner=25
Mar 11 23:47:44 kangur bttv0: i2c: checking for MSP34xx @ 0x80... not found
Mar 11 23:47:44 kangur bttv0: i2c: checking for TDA9875 @ 0xb0... not found
Mar 11 23:47:44 kangur bttv0: i2c: checking for TDA7432 @ 0x8a... not found
Mar 11 23:47:44 kangur tvaudio: TV audio decoder + audio/video mux driver
Mar 11 23:47:44 kangur tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 (PV951),ta8874z
Mar 11 23:47:44 kangur bttv0: i2c: checking for TDA9887 @ 0x86... not found
Mar 11 23:47:44 kangur tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
Mar 11 23:47:44 kangur tuner 0-0061: type set to 25 (LG PAL_I+FM (TAPC-I001D))
Mar 11 23:47:44 kangur bttv0: registered device video0
Mar 11 23:47:44 kangur bttv0: registered device vbi0
Mar 11 23:47:44 kangur bttv0: registered device radio0
Mar 11 23:47:44 kangur bttv0: PLL: 28636363 => 35468950 .. ok
Mar 11 23:47:44 kangur bttv0: add subdevice "remote0"
Mar 11 23:47:44 kangur uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Mar 11 23:47:44 kangur usb 1-2: khubd timed out on ep0in
Mar 11 23:47:44 kangur gameport: pci0000:00:0b.1 speed 1242 kHz
Mar 11 23:47:44 kangur nvidia: module license 'NVIDIA' taints kernel.
Mar 11 23:47:44 kangur ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
Mar 11 23:47:44 kangur ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 (level, low) -> IRQ 10
Mar 11 23:47:44 kangur NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
Mar 11 23:47:44 kangur Real Time Clock Driver v1.12
Mar 11 23:47:44 kangur Floppy drive(s): fd0 is 1.44M
Mar 11 23:47:44 kangur FDC 0 is a post-1991 82077
Mar 11 23:47:44 kangur Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
Mar 11 23:47:44 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 11 23:47:44 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar 11 23:47:44 kangur pnp: the driver 'serial' has been registered
Mar 11 23:47:44 kangur pnp: match found with the PnP device '00:07' and the driver 'serial'
Mar 11 23:47:44 kangur ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 11 23:47:44 kangur pnp: match found with the PnP device '00:08' and the driver 'serial'
Mar 11 23:47:44 kangur ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Mar 11 23:47:44 kangur usb 1-2: khubd timed out on ep0out
Mar 11 23:47:45 kangur eth0: link down
Mar 11 23:47:46 kangur eth0: link down
Mar 11 23:47:47 kangur NET: Registered protocol family 10
Mar 11 23:47:47 kangur Disabled Privacy Extensions on device b03e7aa0(lo)
Mar 11 23:47:47 kangur IPv6 over IPv4 tunneling driver
Also two more questions:
1. What is VIA fixup? Is it some hardware bug? Or BIOS problem? Why is it needed? On what hardware / software it is needed?
2. Why this patch shrinked bzImage that much:
-rw-r--r-- 1 root root 1828186 mar 11 23:33 vmlinuz-2.6.11-cko1 -rw-r--r-- 1 root root 1828355 mar 2 20:48 vmlinuz-2.6.11-cko1.old
What is your next guess?
Thanks,
Grzegorz Kulewski - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
