The SPI-connected CPLD chip controls access to the main NAND flash
chip and five LEDs.
Signed-off-by: Bert Vermeulen <b...@biot.com>
---
arch/mips/include/asm/mach-ath79/rb4xx_cpld.h | 49 +++++
drivers/mfd/Kconfig | 7 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rb4xx-cpld.c | 279 ++++++++++++++++++++++++++
4 files changed, 336 insertions(+)
create mode 100644 arch/mips/include/asm/mach-ath79/rb4xx_cpld.h
create mode 100644 drivers/mfd/rb4xx-cpld.c
diff --git a/arch/mips/include/asm/mach-ath79/rb4xx_cpld.h
b/arch/mips/include/asm/mach-ath79/rb4xx_cpld.h
new file mode 100644
index 0000000..40c109c
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/rb4xx_cpld.h
@@ -0,0 +1,49 @@
+/*
+ * SPI driver definitions for the CPLD chip on the Mikrotik RB4xx boards
+ *
+ * Copyright (C) 2010 Gabor Juhos <juh...@openwrt.org>
+ *
+ * This file was based on the patches for Linux 2.6.27.39 published by
+ * MikroTik for their RouterBoard 4xx series devices.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#define CPLD_GPIO_LED1 0
+#define CPLD_GPIO_LED2 1
+#define CPLD_GPIO_LED3 2
+#define CPLD_GPIO_LED4 3
+#define CPLD_GPIO_FAN 4
+#define CPLD_GPIO_ALE 5
+#define CPLD_GPIO_CLE 6
+#define CPLD_GPIO_nCE 7
+#define CPLD_GPIO_LED5 8
+
+#define CPLD_NUM_GPIOS 9
+
+#define CPLD_CFG_LED1 BIT(CPLD_GPIO_LED1)
+#define CPLD_CFG_LED2 BIT(CPLD_GPIO_LED2)
+#define CPLD_CFG_LED3 BIT(CPLD_GPIO_LED3)
+#define CPLD_CFG_LED4 BIT(CPLD_GPIO_LED4)
+#define CPLD_CFG_FAN BIT(CPLD_GPIO_FAN)
+#define CPLD_CFG_ALE BIT(CPLD_GPIO_ALE)
+#define CPLD_CFG_CLE BIT(CPLD_GPIO_CLE)
+#define CPLD_CFG_nCE BIT(CPLD_GPIO_nCE)
+#define CPLD_CFG_LED5 BIT(CPLD_GPIO_LED5)
+
+#define CPLD_CMD_WRITE_NAND 0x08 /* send cmd, n x send data, send idle */
+#define CPLD_CMD_WRITE_CFG 0x09 /* send cmd, n x send cfg */
+#define CPLD_CMD_READ_NAND 0x0a /* send cmd, send idle, n x read data */
+#define CPLD_CMD_READ_FAST 0x0b /* send cmd, 4 x idle, n x read data */
+#define CPLD_CMD_LED5_ON 0x0c /* send cmd */
+#define CPLD_CMD_LED5_OFF 0x0d /* send cmd */
+
+struct rb4xx_cpld_platform_data {
+ unsigned gpio_base;
+};
+
+extern int rb4xx_cpld_read(struct spi_device *spi, unsigned char *rx_buf,
+ unsigned len);
+extern int rb4xx_cpld_write(struct spi_device *spi, const u8 *buf, int len);
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 38356e3..c4a6a4e 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -631,6 +631,13 @@ config MFD_SPMI_PMIC
Say M here if you want to include support for the SPMI PMIC
series as a module. The module will be called "qcom-spmi-pmic".
+config MFD_RB4XX_CPLD
+ tristate "MikroTik RB4XX CPLD driver"
+ depends on ATH79 && SPI_RB4XX
+ help
+ Driver for the CPLD chip present on MikroTik RB4xx boards.
+ It controls CPU access to NAND flash and user LEDs.
+
config MFD_RDC321X
tristate "RDC R-321x southbridge"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 19f3d74..6cc9fe3 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -155,6 +155,7 @@ obj-$(CONFIG_MFD_OMAP_USB_HOST) += omap-usb-host.o
omap-usb-tll.o
obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o ssbi.o
obj-$(CONFIG_MFD_QCOM_RPM) += qcom_rpm.o
obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
+obj-$(CONFIG_MFD_RB4XX_CPLD) += rb4xx-cpld.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
diff --git a/drivers/mfd/rb4xx-cpld.c b/drivers/mfd/rb4xx-cpld.c
new file mode 100644
index 0000000..0f8de62
--- /dev/null
+++ b/drivers/mfd/rb4xx-cpld.c
@@ -0,0 +1,279 @@
+/*
+ * SPI driver for the CPLD chip on the Mikrotik RB4xx boards
+ *
+ * Copyright (C) 2010 Gabor Juhos <juh...@openwrt.org>
+ *
+ * This file was based on the patches for Linux 2.6.27.39 published by
+ * MikroTik for their RouterBoard 4xx series devices.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/bitops.h>
+#include <linux/spi/spi.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+
+#include <asm/mach-ath79/rb4xx_cpld.h>
+
+struct rb4xx_cpld {
+ struct spi_device *spi;
+ struct mutex lock;
+ struct gpio_chip chip;
+ unsigned int config;
+};
+
+static inline struct rb4xx_cpld *gpio_to_cpld(struct gpio_chip *chip)
+{
+ return container_of(chip, struct rb4xx_cpld, chip);
+}
+
+static int rb4xx_cpld_write_cmd(struct rb4xx_cpld *cpld, unsigned char cmd)
+{
+ struct spi_transfer t[1];
+ struct spi_message m;
+ unsigned char tx_buf[1];
+ int err;
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t[0].tx_buf = tx_buf;
+ t[0].len = sizeof(tx_buf);
+ spi_message_add_tail(&t[0], &m);
+
+ tx_buf[0] = cmd;
+
+ err = spi_sync(cpld->spi, &m);
+ return err;
+}
+
+static int rb4xx_cpld_write_cfg(struct rb4xx_cpld *cpld, unsigned char config)
+{
+ struct spi_transfer t[1];
+ struct spi_message m;
+ unsigned char cmd[2];
+ int err;
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t[0].tx_buf = cmd;
+ t[0].len = sizeof(cmd);
+ spi_message_add_tail(&t[0], &m);
+
+ cmd[0] = CPLD_CMD_WRITE_CFG;
+ cmd[1] = config;
+
+ err = spi_sync(cpld->spi, &m);
+ return err;
+}
+
+static int rb4xx_cpld_change_cfg(struct rb4xx_cpld *cpld, u32 mask, u32 value)
+{
+ unsigned int config;
+ int err;
+
+ config = cpld->config & ~mask;
+ config |= value;
+
+ if ((cpld->config ^ config) & 0xff) {
+ err = rb4xx_cpld_write_cfg(cpld, config);
+ if (err)
+ return err;
+ }
+
+ if ((cpld->config ^ config) & CPLD_CFG_LED5) {
+ err = rb4xx_cpld_write_cmd(cpld, (value) ? CPLD_CMD_LED5_ON :
+ CPLD_CMD_LED5_OFF);
+ if (err)
+ return err;
+ }
+
+ cpld->config = config;
+ return 0;
+}
+
+int rb4xx_cpld_read(struct spi_device *spi, unsigned char *rx_buf, unsigned
len)
+{
+ struct spi_message m;
+ static const unsigned char cmd[2] = { CPLD_CMD_READ_NAND, 0 };
+ struct spi_transfer t[2] = {
+ {
+ .tx_buf = &cmd,
+ .len = 2,
+ }, {
+ .rx_buf = rx_buf,
+ .len = len,
+ },
+ };
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+ spi_message_add_tail(&t[1], &m);
+ return spi_sync(spi, &m);
+}
+EXPORT_SYMBOL_GPL(rb4xx_cpld_read);
+
+/* The cs_change flag indicates to the spi-rb4xx driver to use "fast mode". */
+int rb4xx_cpld_write(struct spi_device *spi, const u8 *buf, int len)
+{
+ struct spi_message m;
+ static const unsigned char cmd = CPLD_CMD_WRITE_NAND;
+ static const unsigned char dummy = 0x00;
+ struct spi_transfer t[3] = {
+ {
+ .tx_buf = &cmd,
+ .len = 1,
+ }, {
+ .tx_buf = buf,
+ .len = len,
+ .cs_change = 1,
+ }, {
+ .tx_buf = &dummy,
+ .len = 1,
+ .cs_change = 1,
+ },
+ };
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+ spi_message_add_tail(&t[1], &m);
+ spi_message_add_tail(&t[2], &m);
+ return spi_sync(spi, &m);
+}
+EXPORT_SYMBOL_GPL(rb4xx_cpld_write);
+
+static int rb4xx_cpld_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+ int ret;
+
+ mutex_lock(&cpld->lock);
+ ret = (cpld->config >> offset) & 1;
+ mutex_unlock(&cpld->lock);
+
+ return ret;
+}
+
+static void rb4xx_cpld_gpio_set(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+
+ mutex_lock(&cpld->lock);
+ rb4xx_cpld_change_cfg(cpld, (1 << offset), !!value << offset);
+ mutex_unlock(&cpld->lock);
+}
+
+static int rb4xx_cpld_gpio_direction_input(struct gpio_chip *chip,
+ unsigned offset)
+{
+ return -EOPNOTSUPP;
+}
+
+static int rb4xx_cpld_gpio_direction_output(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+ int ret;
+
+ mutex_lock(&cpld->lock);
+ ret = rb4xx_cpld_change_cfg(cpld, (1 << offset), !!value << offset);
+ mutex_unlock(&cpld->lock);
+
+ return ret;
+}
+
+static int rb4xx_cpld_gpio_init(struct rb4xx_cpld *cpld, unsigned int base)
+{
+ int err;
+
+ cpld->chip.label = "rb4xx-cpld";
+ cpld->chip.base = base;
+ cpld->chip.ngpio = CPLD_NUM_GPIOS;
+ cpld->chip.can_sleep = 1;
+ cpld->chip.dev = &cpld->spi->dev;
+ cpld->chip.owner = THIS_MODULE;
+ cpld->chip.get = rb4xx_cpld_gpio_get;
+ cpld->chip.set = rb4xx_cpld_gpio_set;
+ cpld->chip.direction_input = rb4xx_cpld_gpio_direction_input;
+ cpld->chip.direction_output = rb4xx_cpld_gpio_direction_output;
+
+ err = gpiochip_add(&cpld->chip);
+ if (err)
+ dev_err(&cpld->spi->dev, "adding GPIO chip failed, error %d\n",
+ err);
+
+ return err;
+}
+
+static int rb4xx_cpld_probe(struct spi_device *spi)
+{
+ struct rb4xx_cpld *cpld;
+ struct rb4xx_cpld_platform_data *pdata;
+ int err;
+
+ pdata = spi->dev.platform_data;
+ if (!pdata) {
+ dev_dbg(&spi->dev, "no platform data\n");
+ return -EINVAL;
+ }
+
+ cpld = devm_kzalloc(&spi->dev, sizeof(*cpld), GFP_KERNEL);
+ if (!cpld)
+ return -ENOMEM;
+
+ mutex_init(&cpld->lock);
+ cpld->spi = spi_dev_get(spi);
+ dev_set_drvdata(&spi->dev, cpld);
+
+ spi->mode = SPI_MODE_0;
+ err = spi_setup(spi);
+ if (err) {
+ dev_err(&spi->dev, "SPI setup failed, error %d\n", err);
+ return err;
+ }
+
+ err = rb4xx_cpld_gpio_init(cpld, pdata->gpio_base);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+static int rb4xx_cpld_remove(struct spi_device *spi)
+{
+ struct rb4xx_cpld_platform_data *pdata;
+ struct rb4xx_cpld *cpld;
+
+ pdata = spi->dev.platform_data;
+ cpld = dev_get_drvdata(&spi->dev);
+ mutex_destroy(&cpld->lock);
+
+ return 0;
+}
+
+static struct spi_driver rb4xx_cpld_driver = {
+ .probe = rb4xx_cpld_probe,
+ .remove = rb4xx_cpld_remove,
+ .driver = {
+ .name = "rb4xx-cpld",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+};
+
+module_spi_driver(rb4xx_cpld_driver);
+
+MODULE_DESCRIPTION("RB4xx CPLD driver");
+MODULE_AUTHOR("Gabor Juhos <juh...@openwrt.org>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
