Hi all,
I borrowed a Zaapa LR301AP DVB-T card from a friend to try to make it work in
Linux, so I kindly request your help. The card features one antenna input, one
IR input (remote and sensor wire being lost) and one AV input. Here follows
the system info:
On-board printed info:
************************
Main chip: Philips SAA 7134 HL
Other chips: TDA 10046A, TDA 8274, MDT 2005ES-G.
lspci -vnn
****************
00:0c.0 Multimedia controller [0480]: Philips Semiconductors SAA7134/SAA7135HL
Video Broadcast Decoder [1131:7134] (rev 01)
Subsystem: Device [4e42:0301]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at dffffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Kernel driver in use: saa7134
dmesg | grep saa
*******************
saa7130/34: v4l2 driver version 0.2.15 loaded
[ 8.854415] saa7134 0000:00:0c.0: PCI INT A -> Link[LNKB] -> GSI 11 (level,
low) -> IRQ 11
[ 8.854423] saa7134[0]: found at 0000:00:0c.0, rev: 1, irq: 11, latency:
64, mmio: 0xdffffc00
[ 8.854430] saa7134[0]: subsystem: 4e42:0301, board: UNKNOWN/GENERIC
[card=0,autodetected]
[ 8.854453] saa7134[0]: board init: gpio is 10000
[ 8.854458] IRQ 11/saa7134[0]: IRQF_DISABLED is not guaranteed on shared
IRQs
[ 9.004012] saa7134[0]: i2c eeprom 00: 42 4e 01 03 54 20 1c 00 43 43 a9 1c
55 d2 b2 92
[ 9.004022] saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff
ff ff ff ff
[ 9.004030] saa7134[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 e2
ff ff ff ff
[ 9.004038] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004045] saa7134[0]: i2c eeprom 40: ff 1b 00 c0 ff 10 01 00 ff ff ff ff
ff ff ff ff
[ 9.004052] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004059] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004067] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004074] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004081] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004089] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004096] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004103] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004111] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004118] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004125] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004271] saa7134[0]: registered device video0 [v4l2]
[ 9.004299] saa7134[0]: registered device vbi0
[ 9.565411] saa7134 ALSA driver for DMA sound loaded
[ 9.565424] IRQ 11/saa7134[0]: IRQF_DISABLED is not guaranteed on shared
IRQs
[ 9.565451] saa7134[0]/alsa: saa7134[0] at 0xdffffc00 irq 11 registered as
card -1
[ 3368.737762] saa7134[0]/irq[10,4295734480]: r=0x20 s=0x00 PE
[ 3368.737770] saa7134[0]/irq: looping -- clearing PE (parity error!) enable
bit
************************************************************************************
No DVB-T button appears in Kaffeine, so the card is not being detected by the
app.
Thanks for any help
Antonio
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
