Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudh...@stericsson.com>
---
drivers/mmc/core/core.c | 35 +++++++++++++++++++++++------------
drivers/mmc/core/core.h | 4 ++--
drivers/mmc/core/mmc.c | 8 ++++----
drivers/mmc/core/sd.c | 2 +-
drivers/mmc/core/sdio.c | 3 +--
5 files changed, 31 insertions(+), 21 deletions(-)
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 285f064..03db641 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1219,7 +1219,26 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
return ocr;
}
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool
cmd11)
+int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
+{
+ int err = 0;
+ int old_signal_voltage = host->ios.signal_voltage;
+
+ host->ios.signal_voltage = signal_voltage;
+ if (host->ops->start_signal_voltage_switch) {
+ mmc_host_clk_hold(host);
+ err = host->ops->start_signal_voltage_switch(host, &host->ios);
+ mmc_host_clk_release(host);
+ }
+
+ if (err)
+ host->ios.signal_voltage = old_signal_voltage;
+
+ return err;
+
+}
+
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
struct mmc_command cmd = {0};
int err = 0;
@@ -1230,7 +1249,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int
signal_voltage, bool cmd11
* Send CMD11 only if the request is to switch the card to
* 1.8V signalling.
*/
- if ((signal_voltage != MMC_SIGNAL_VOLTAGE_330) && cmd11) {
+ if (signal_voltage != MMC_SIGNAL_VOLTAGE_330) {
cmd.opcode = SD_SWITCH_VOLTAGE;
cmd.arg = 0;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
@@ -1243,15 +1262,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int
signal_voltage, bool cmd11
return -EIO;
}
- host->ios.signal_voltage = signal_voltage;
-
- if (host->ops->start_signal_voltage_switch) {
- mmc_host_clk_hold(host);
- err = host->ops->start_signal_voltage_switch(host, &host->ios);
- mmc_host_clk_release(host);
- }
-
- return err;
+ return __mmc_set_signal_voltage(host, signal_voltage);
}
/*
@@ -1314,7 +1325,7 @@ static void mmc_power_up(struct mmc_host *host)
mmc_set_ios(host);
/* Set signal voltage to 3.3V */
- mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false);
+ __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
/*
* This delay should be sufficient to allow the power supply
diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h
index 4a90067..f2439d5 100644
--- a/drivers/mmc/core/core.h
+++ b/drivers/mmc/core/core.h
@@ -40,8 +40,8 @@ void mmc_set_ungated(struct mmc_host *host);
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode);
void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage,
- bool cmd11);
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
+int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
void mmc_set_timing(struct mmc_host *host, unsigned int timing);
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
void mmc_power_off(struct mmc_host *host);
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index e6e3911..bd86771 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -769,11 +769,11 @@ static int mmc_select_hs200(struct mmc_card *card)
if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0);
+ err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
if (err && card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_8V &&
host->caps2 & MMC_CAP2_HS200_1_8V_SDR)
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, 0);
+ err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
/* If fails try again during next card power cycle */
if (err)
@@ -1221,8 +1221,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
* WARNING: eMMC rules are NOT the same as SD DDR
*/
if (ddr == MMC_1_2V_DDR_MODE) {
- err = mmc_set_signal_voltage(host,
- MMC_SIGNAL_VOLTAGE_120, 0);
+ err = __mmc_set_signal_voltage(host,
+ MMC_SIGNAL_VOLTAGE_120);
if (err)
goto err;
}
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 74972c2..0cc1b26 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -759,7 +759,7 @@ try_again:
*/
if (!mmc_host_is_spi(host) && rocr &&
((*rocr & 0x41000000) == 0x41000000)) {
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
true);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
if (err) {
ocr &= ~SD_OCR_S18R;
goto try_again;
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index 2273ce6..0c84e0f 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -650,8 +650,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32
ocr,
(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
MMC_CAP_UHS_DDR50))) {
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
- true);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
if (err) {
ocr &= ~R4_18V_PRESENT;
host->ocr &= ~R4_18V_PRESENT;
--
1.7.10
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
