I got my modem to work using setserial but, how do I get my system
to configure ttyS3 for irq 4 at boot-up?
Here is the file you wonted Akintayo Holder. Just use "pnpdump
--config > /dev/ttyS3".
Thanks,
Micah
# $Id: pnpdump.c,v 1.17 1998/11/10 22:45:04 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier 27 ff ff ff ff 68 18 73 16
# Board 2 has serial identifier 2a 00 00 01 01 01 a0 89 6a
# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 27 ff ff ff ff 68 18 73 16)
# Vendor Id ESS1868, No Serial Number (-1), checksum 0x27.
# Version 1.0, Vendor version 1.0
# ANSI string -->ESS ES1868 Plug and Play AudioDrive<--
#
# Logical device id ESS0000
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 0
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ff8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x0800))
(NAME "ESS1868/-1[0]{ESS ES1868 Plug and Play AudioDrive}")
(ACT Y)
))
#
# Logical device id ESS1868
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 1
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 0 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
# Fixed IO base address 0x0220
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
(IO 1 (SIZE 4) (BASE 0x0388))
# Fixed IO base address 0x0330
# Number of IO addresses required: 2
(IO 2 (SIZE 2) (BASE 0x0330))
# Start dependent functions: priority acceptable
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
# Start dependent functions: priority functional
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0800))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
# End dependent functions
(NAME "ESS1868/-1[1]{ESS ES1868 Plug and Play AudioDrive}")
(ACT Y)
))
#
# Logical device id ESS0001
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 2
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Fixed IO base address 0x0201
# Number of IO addresses required: 1
(IO 0 (SIZE 1) (BASE 0x0201))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x020f
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0200))
# End dependent functions
# Compatible device id PNPb02f
(NAME "ESS1868/-1[2]{ESS ES1868 Plug and Play AudioDrive}")
(ACT Y)
))
#
# Logical device id ESS0002
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 3
#
# Multiple choice time, choose one only !
#
# Start dependent functions: priority preferred
# IRQ 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 12 (MODE +E)))
# Fixed IO base address 0x0168
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0168))
# Fixed IO base address 0x036e
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x036e))
#
# Start dependent functions: priority acceptable
# IRQ 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Fixed IO base address 0x0168
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0168))
# Fixed IO base address 0x036e
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x036e))
#
# Start dependent functions: priority acceptable
# IRQ 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Fixed IO base address 0x01e8
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x01e8))
# Fixed IO base address 0x03ee
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x03ee))
#
# Start dependent functions: priority functional
# IRQ 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x01f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#
# End dependent functions
# Compatible device id PNP0600
# (NAME "ESS1868/-1[3]{ESS ES1868 Plug and Play AudioDrive}")
# (ACT Y)
))
#
# Logical device id ESS0002
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 3
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 12.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 12 (MODE +E)))
# Fixed IO base address 0x0168
# Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x0168))
# Fixed IO base address 0x036e
# Number of IO addresses required: 2
(IO 1 (SIZE 2) (BASE 0x036e))
# Start dependent functions: priority acceptable
# IRQ 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Fixed IO base address 0x0168
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0168))
# Fixed IO base address 0x036e
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x036e))
# Start dependent functions: priority acceptable
# IRQ 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Fixed IO base address 0x01e8
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x01e8))
# Fixed IO base address 0x03ee
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x03ee))
# Start dependent functions: priority functional
# IRQ 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x01f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# End dependent functions
# Compatible device id PNP0600
(NAME "ESS1868/-1[3]{ESS ES1868 Plug and Play AudioDrive}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 2a 00 00 01 01 01 a0 89 6a)
# Vendor Id ZTIa001, Serial Number 257, checksum 0x2A.
# Version 1.0, Vendor version 0.1
# ANSI string -->Zoom Internal V90 Faxmodem#
# Logical device id ZTIa001
# Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ZTIa001/257 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8))
# IRQ 4.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 4 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8))
# IRQ 3.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8))
# IRQ 4.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 4 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02e8))
# IRQ 3.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8))
# IRQ 3, 4, 5, 7, 9, 10, 12 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8))
# IRQ 3, 4, 5, 7, 9, 10, 12 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8))
# IRQ 3, 4, 5, 7, 9, 10, 12 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x02e8))
# IRQ 3, 4, 5, 7, 9, 10, 12 or 15.
# High true, edge sensitive interrupt
(INT 0 (IRQ 4 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100))
# IRQ 3, 4, 5, 7, 9, 10, 12 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0100))
(NAME "ZTIa001/257[0]{Zoom Internal V90 Faxmodem}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
