Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.

Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.

For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.

Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 & OMAP4.

Cc: Tony Lindgren <t...@atomide.com>
Cc: Andrew Morton <a...@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu...@ti.com>
Cc: Adrian Hunter <adrian.hun...@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiy...@ti.com>
---
 arch/arm/mach-omap2/board-4430sdp.c |    7 +++-
 drivers/mfd/twl6030-irq.c           |   73 +++++++++++++++++++++++++++++++++++
 drivers/mmc/host/omap_hsmmc.c       |    4 +-
 include/linux/i2c/twl.h             |   31 +++++++++++++++
 4 files changed, 112 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/board-4430sdp.c 
b/arch/arm/mach-omap2/board-4430sdp.c
index 9447644..a49f285 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -227,9 +227,14 @@ static int omap4_twl6030_hsmmc_late_init(struct device 
*dev)
        struct omap_mmc_platform_data *pdata = dev->platform_data;

        /* Setting MMC1 Card detect Irq */
-       if (pdev->id == 0)
+       if (pdev->id == 0) {
+               ret = twl6030_mmc_card_detect_config();
+               if (ret)
+                       pr_err("Failed configuring MMC1 card detect\n");
                pdata->slots[0].card_detect_irq = TWL6030_IRQ_BASE +
                                                MMCDETECT_INTR_OFFSET;
+               pdata->slots[0].card_detect = twl6030_mmc_card_detect;
+       }
        return ret;
 }

diff --git a/drivers/mfd/twl6030-irq.c b/drivers/mfd/twl6030-irq.c
index 10bf228..2d3bb82 100644
--- a/drivers/mfd/twl6030-irq.c
+++ b/drivers/mfd/twl6030-irq.c
@@ -36,6 +36,7 @@
 #include <linux/irq.h>
 #include <linux/kthread.h>
 #include <linux/i2c/twl.h>
+#include <linux/platform_device.h>

 /*
  * TWL6030 (unlike its predecessors, which had two level interrupt handling)
@@ -223,6 +224,78 @@ int twl6030_interrupt_mask(u8 bit_mask, u8 offset)
 }
 EXPORT_SYMBOL(twl6030_interrupt_mask);

+int twl6030_mmc_card_detect_config(void)
+{
+       int ret;
+       u8 reg_val = 0;
+
+       /* Unmasking the Card detect Interrupt line for MMC1 from Phoenix */
+       twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
+                                               REG_INT_MSK_LINE_B);
+       twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
+                                               REG_INT_MSK_STS_B);
+       /*
+        * Intially Configuring MMC_CTRL for receving interrupts &
+        * Card status on TWL6030 for MMC1
+        */
+       ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &reg_val, TWL6030_MMCCTRL);
+       if (ret < 0) {
+               pr_err("twl6030: Failed to read MMCCTRL, error %d\n", ret);
+               return ret;
+       }
+       reg_val &= ~VMMC_AUTO_OFF;
+       reg_val |= SW_FC;
+       ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val, TWL6030_MMCCTRL);
+       if (ret < 0) {
+               pr_err("twl6030: Failed to write MMCCTRL, error %d\n", ret);
+               return ret;
+       }
+
+       /* Configuring PullUp-PullDown register */
+       ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &reg_val,
+                                               TWL6030_CFG_INPUT_PUPD3);
+       if (ret < 0) {
+               pr_err("twl6030: Failed to read CFG_INPUT_PUPD3, error %d\n",
+                                                                       ret);
+               return ret;
+       }
+       reg_val &= ~(MMC_PU | MMC_PD);
+       ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val,
+                                               TWL6030_CFG_INPUT_PUPD3);
+       if (ret < 0) {
+               pr_err("twl6030: Failed to write CFG_INPUT_PUPD3, error %d\n",
+                                                                       ret);
+               return ret;
+       }
+       return 0;
+}
+EXPORT_SYMBOL(twl6030_mmc_card_detect_config);
+
+int twl6030_mmc_card_detect(struct device *dev, int slot)
+{
+       int ret = -EIO;
+       u8 read_reg = 0;
+       struct platform_device *pdev = to_platform_device(dev);
+
+       if (pdev->id) {
+               /* TWL6030 provide's Card detect support for
+                * only MMC1 controller.
+                */
+               pr_err("Unkown MMC controller %d in %s\n", pdev->id, __func__);
+               return ret;
+       }
+       /*
+        * BIT0 of MMC_CTRL on TWL6030 provides card status for MMC1
+        * 0 - Card not present ,1 - Card present
+        */
+       ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &read_reg,
+                                               TWL6030_MMCCTRL);
+       if (ret >= 0)
+               ret = read_reg & STS_MMC;
+       return ret;
+}
+EXPORT_SYMBOL(twl6030_mmc_card_detect);
+
 int twl6030_init_irq(int irq_num, unsigned irq_base, unsigned irq_end)
 {

diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 562dbbb..a51894d 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -466,8 +466,6 @@ static int omap_hsmmc_gpio_init(struct 
omap_mmc_platform_data *pdata)
        int ret;

        if (gpio_is_valid(pdata->slots[0].switch_pin)) {
-               pdata->suspend = omap_hsmmc_suspend_cdirq;
-               pdata->resume = omap_hsmmc_resume_cdirq;
                if (pdata->slots[0].cover)
                        pdata->slots[0].get_cover_state =
                                        omap_hsmmc_get_cover_state;
@@ -2211,6 +2209,8 @@ static int __init omap_hsmmc_probe(struct platform_device 
*pdev)
                                "Unable to grab MMC CD IRQ\n");
                        goto err_irq_cd;
                }
+               pdata->suspend = omap_hsmmc_suspend_cdirq;
+               pdata->resume = omap_hsmmc_resume_cdirq;
        }

        omap_hsmmc_disable_irq(host);
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
index 6de90bf..e64894c 100644
--- a/include/linux/i2c/twl.h
+++ b/include/linux/i2c/twl.h
@@ -141,6 +141,16 @@
 #define TWL6030_CHARGER_CTRL_INT_MASK  0x10
 #define TWL6030_CHARGER_FAULT_INT_MASK         0x60

+#define TWL6030_MMCCTRL                0xEE
+#define VMMC_AUTO_OFF                  (0x1 << 3)
+#define SW_FC                          (0x1 << 2)
+#define STS_MMC                        0x1
+
+#define TWL6030_CFG_INPUT_PUPD3        0xF2
+#define MMC_PU                         (0x1 << 3)
+#define MMC_PD                         (0x1 << 2)
+
+

 #define TWL4030_CLASS_ID               0x4030
 #define TWL6030_CLASS_ID               0x6030
@@ -173,6 +183,27 @@ int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned 
num_bytes);
 int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
 int twl6030_interrupt_mask(u8 bit_mask, u8 offset);

+/* Card detect Configuration for MMC1 Controller on OMAP4 */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect_config(void);
+#else
+static inline int twl6030_mmc_card_detect_config(void)
+{
+       pr_debug("twl6030_mmc_card_detect_config not supported\n");
+       return 0;
+}
+#endif
+
+/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect(struct device *dev, int slot);
+#else
+static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
+{
+       pr_debug("Call back twl6030_mmc_card_detect not supported\n");
+       return -EIO;
+}
+#endif
 /*----------------------------------------------------------------------*/

 /*
-- 
1.7.0.4


--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to