On Sat, 28 Jan 2012, NeilBrown wrote: > On Thu, 26 Jan 2012 07:19:19 -0700 (MST) Paul Walmsley <p...@pwsan.com> wrote: > > > Thanks. Should I add a Tested-by: from you on those patches? > > Well... I only tested them after backporting to 3.2, and Linus is a big > proponent of the idea that once you rebase patches you invalidate any > testing.... > However I don't think there difference between 3.2 and 3.3-rc1 is big enough > in the area, so yes: > > Tested-by: NeilBrown <ne...@suse.de>
Okay, thanks. > > Here's a theory: perhaps the MPU powerdomain is hitting a low-power state > > while waiting for an HDQ interrupt. When the MPU powerdomain is in a low > > power state, so is the MPU interrupt controller, so the only way that the > > MPU can wake up is if the HDQ can issue a wakeup event to the PRCM. And I > > don't see any evidence that the HDQ is capable of doing this, based on the > > HDQ sections of the TRM. What a huge energy waste, if true. > > In the config I am testing MPU only goes to RET, never OFF. Same for CORE. That qualifies as a low-power state for the MPU :-) In MPU RET, at least in theory, the MPU INTC will not be operational, and thus unable to respond to interrupts. > > Maybe try something like the following patch -- compile-tested only here. > > > > If this works, you might want to try dropping this patch and using the pad > > mux to set a wakeup event on the 1-wire pad when the signal goes low. > > That might be a more power-efficient approach. You may still have to use > > some PM QoS request there to ensure that the HDQ can wake up fast enough > > to see the pulse, but the constraint shouldn't need to be as ludicrously > > low as it is in the following patch. > > Doesn't work - crashes :-( > > pm_qos_power_init is defined as a late_initcall, so you cannot call > pm_qos_update_request until after all the initcalls have run. > But with your patch, the probe of the bq27000 triggers a read of the registers > which tries to update_request - and it goes 'bang'. Hmm, okay. Could you please remove the register read from the HDQ probe and see if that makes a difference? > I really think the problem is the CORE pwrdm gating a clock because no module > says it needs it - i.e. nothing to do with MPU at all. Until pm_runtime_put*() is called, the usecount of hdq_fck will still be non-zero. So the CORE shouldn't be able to gate it or hdq_ick at that time, and thus should not be able to enter idle. Hence the question about where the problems occur: whether they occur in the middle of the transaction or when the HDQ clocks are disabled. > We want to keep CORE active when an HDQ transaction is happening, but MPU is > welcome to go to sleep. I don't think you can express that with 'qos'. I > think it needs some omap-specific machinery. The OMAP PRCM hardware should keep the CORE* clkdms active when the hdq_fck is enabled. So it's possible there could be a PRCM silicon bug that doesn't take hdq_fck into account when determining whether the CORE_* clkdms are inactive. > I can 'fix' the problem simply by making sure > > pwrdm_for_each_clkdm(core_pd, _cpuidle_deny_idle); > > runs in omap3_enter_idle whenever HDQ is active. Hmm, that does suggest that it's not wakeup related. > One of the reasons that I think it is a clock problem rather than just > missing a wakeup event is that once the problem starts happening I > cannot recovery without rebooting. i.e. even if I tell the UARTs to keep > the clocks on permanently and keep the CPUIDLE state at 0, the HDQ > doesn't start working again. It has clearly become confused. The HDQ > doco makes a point of saying that you shouldn't issue any commands > (except 'enable clock') when the clock is disabled. I think we end up > doing that and it gets confused and cannot recover. > > I note that there is an ad-hoc dependency between the camera and various > power states as well. Maybe we need a little bit of infrastructure so > that camera can say "Keep CORE and MPU on" (or whatever it needs) and > HDQ can say "Keep CORE on". ??? I'm not familiar with the camera problems, but in the HDQ case, this should only be needed if a silicon bug exists. Which is certainly possible; we've seen this problem with one other IP block in the past. Based on a quick glance at the errata, I don't see anything related to the HDQ, but that doesn't really mean anything. In any case, we should be able to work around this via the hwmod layer and a special flag, if the problem really is a PRCM bug. This will depend on the functional powerstate conversion. Thanks for the detailed test reports. - Paul -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html