Hello,

On 06/05/2013 07:08 PM, Mugunthan V N wrote:
Add pinmux configurations for MII based CPSW ethernet to am335x-bone.
In this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Todo:
- if an idle state is available for pins, add support for it.

Signed-off-by: Mugunthan V N <mugunthan...@ti.com>
---
  arch/arm/boot/dts/am335x-bone.dts |   38 +++++++++++++++++++++++++++++++++++++
  1 file changed, 38 insertions(+)

diff --git a/arch/arm/boot/dts/am335x-bone.dts 
b/arch/arm/boot/dts/am335x-bone.dts
index 4b5a8e0..008a13b 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -36,6 +36,33 @@
                                0x60 0x17       /* gpmc_a8.gpio1_24, 
OUTPUT_PULLUP | MODE7 */
                        >;
                };
+
+               cpsw_default: cpsw_default {
+                       pinctrl-single,pins = <
+                               /* Slave 1 */
+                               0x110 0x20      /* mii1_rxerr.mii1_rxerr, MODE0 
| INPUT */

Here I guess that the comment should be INPUT_PULLDOWN, instead of INPUT.

+                               0x114 0x0       /* mii1_txen.mii1_txen, MODE0 | 
OUTPUT */

As bit PULLUDENABLE is 0, the pulldown is enabled according to the TRM, right? Is this a desirable behaviour, as it will consume power when outputting a high level?
And consequently, the comment should probably be OUTPUT_PULLDOWN, no?

+                               0x118 0x20      /* mii1_rxdv.mii1_rxdv, MODE0 | 
INPUT_PULLDOWN */
+                               0x11c 0x0       /* mii1_txd3.mii1_txd3, MODE0 | 
OUTPUT */
+                               0x120 0x0       /* mii1_txd2.mii1_txd2, MODE0 | 
OUTPUT */
+                               0x124 0x0       /* mii1_txd1.mii1_txd1, MODE0 | 
OUTPUT */
+                               0x128 0x0       /* mii1_txd0.mii1_txd0, MODE0 | 
OUTPUT */

Same questions here.

+                               0x12c 0x20      /* mii1_txclk.mii1_txclk, MODE0 
| INPUT_PULLDOWN */
+                               0x130 0x20      /* mii1_rxclk.mii1_rxclk, MODE0 
| INPUT_PULLDOWN */
+                               0x134 0x20      /* mii1_rxd3.mii1_rxd3, MODE0 | 
INPUT_PULLDOWN */
+                               0x138 0x20      /* mii1_rxd2.mii1_rxd2, MODE0 | 
INPUT_PULLDOWN */
+                               0x13c 0x20      /* mii1_rxd1.mii1_rxd1, MODE0 | 
INPUT_PULLDOWN */
+                               0x140 0x20      /* mii1_rxd0.mii1_rxd0, MODE0 | 
INPUT_PULLDOWN */
+                       >;
+               };
+
+               davinci_mdio_default: davinci_mdio_default {
+                       pinctrl-single,pins = <
+                               /* MDIO */
+                               0x148 0x30      /* mdio_data.mdio_data, MODE0 | 
INPUT_PULLUP */
+                               0x14c 0x10      /* mdio_clk.mdio_clk, MODE0 | 
OUTPUT_PULLUP */
+                       >;
+               };
        };

        ocp {
@@ -138,3 +165,14 @@
        phy_id = <&davinci_mdio>, <1>;
        phy-mode = "mii";
  };
+
+&mac {
+       pinctrl-names = "default";
+       pinctrl-0 = <&cpsw_default>;
+
+};
+
+&davinci_mdio {
+       pinctrl-names = "default";
+       pinctrl-0 = <&davinci_mdio_default>;
+};


Regards,

Florian
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to