From: Geert Uytterhoeven <geert+rene...@glider.be>
The Renesas Salvator-X development board can be equipped with either an
R-Car H3 or M3-W SiP, which are pin-compatible. Both boards use
different DTBs.
Reduce duplication by extracting common Salvator-X board support into
its own .dtsi file. References to SoC-specific clocks are handled
through cpp definitions. Sort device nodes while at it.
For boards with an R-Car H3 SiP, there are no functional changes.
For boards with an R-Car M3-W SiP, the following new devices are now
described in DT:
- External audio, CAN, and PCIe clocks,
- USB Vbus regulator,
- CS2000 clock generator,
- AK4613 Audio Codec,
- VGA.
Signed-off-by: Geert Uytterhoeven <geert+rene...@glider.be>
Signed-off-by: Simon Horman <horms+rene...@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 543 +-------------------
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 259 +---------
arch/arm64/boot/dts/renesas/salvator-x.dtsi | 555 +++++++++++++++++++++
3 files changed, 563 insertions(+), 794 deletions(-)
create mode 100644 arch/arm64/boot/dts/renesas/salvator-x.dtsi
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index ff68bac4cd7e..52fce67df341 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -8,48 +8,16 @@
* kind, whether express or implied.
*/
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- * amixer set "DVC Out" 100%
- * amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- * amixer set "DVC Out Mute" on
- * amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
- * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- * amixer set "DVC Out Ramp" on
- * aplay xxx.wav &
- * amixer set "DVC Out" 80% // Volume Down
- * amixer set "DVC Out" 100% // Volume Up
- */
+#define CPG_AUDIO_CLK_I R8A7795_CLK_S0D4
/dts-v1/;
#include "r8a7795.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-x.dtsi"
/ {
model = "Renesas Salvator-X board based on r8a7795";
compatible = "renesas,salvator-x", "renesas,r8a7795";
- aliases {
- serial0 = &scif2;
- serial1 = &scif1;
- ethernet0 = &avb;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
- stdout-path = "serial0:115200n8";
- };
-
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
@@ -70,531 +38,30 @@
device_type = "memory";
reg = <0x7 0x00000000 0x0 0x40000000>;
};
-
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24576000>;
- };
-
- reg_1p8v: regulator0 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator1 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- vcc_sdhi0: regulator-vcc-sdhi0 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi0: regulator-vccq-sdhi0 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI0 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
- };
-
- vcc_sdhi3: regulator-vcc-sdhi3 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI3 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi3: regulator-vccq-sdhi3 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI3 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
- };
-
- vbus0_usb2: regulator-vbus0-usb2 {
- compatible = "regulator-fixed";
-
- regulator-name = "USB20_VBUS0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- audio_clkout: audio_clkout {
- /*
- * This is same as <&rcar_sound 0>
- * but needed to avoid cs2000/rcar_sound probe dead-lock
- */
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <11289600>;
- };
-
- rsnd_ak4613: sound {
- compatible = "simple-audio-card";
-
- simple-audio-card,format = "left_j";
- simple-audio-card,bitclock-master = <&sndcpu>;
- simple-audio-card,frame-master = <&sndcpu>;
-
- sndcpu: simple-audio-card,cpu {
- sound-dai = <&rcar_sound>;
- };
-
- sndcodec: simple-audio-card,codec {
- sound-dai = <&ak4613>;
- };
- };
-
- vga-encoder {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7123_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
- port@1 {
- reg = <1>;
- adv7123_out: endpoint {
- remote-endpoint = <&vga_in>;
- };
- };
- };
- };
-
- vga {
- compatible = "vga-connector";
-
- port {
- vga_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
- };
};
-&du {
- pinctrl-0 = <&du_pins>;
- pinctrl-names = "default";
+&ehci2 {
status = "okay";
-
- ports {
- port@0 {
- endpoint {
- remote-endpoint = <&adv7123_in>;
- };
- };
- port@3 {
- lvds_connector: endpoint {
- };
- };
- };
-};
-
-&extal_clk {
- clock-frequency = <16666666>;
};
-&extalr_clk {
- clock-frequency = <32768>;
+&ohci2 {
+ status = "okay";
};
&pfc {
- pinctrl-0 = <&scif_clk_pins>;
- pinctrl-names = "default";
-
- scif1_pins: scif1 {
- groups = "scif1_data_a", "scif1_ctrl";
- function = "scif1";
- };
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
- };
- scif_clk_pins: scif_clk {
- groups = "scif_clk_a";
- function = "scif_clk";
- };
-
- i2c2_pins: i2c2 {
- groups = "i2c2_a";
- function = "i2c2";
- };
-
- avb_pins: avb {
- mux {
- groups = "avb_link", "avb_phy_int", "avb_mdc",
- "avb_mii";
- function = "avb";
- };
-
- pins_mdc {
- groups = "avb_mdc";
- drive-strength = <24>;
- };
-
- pins_mii_tx {
- pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
- "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
- drive-strength = <12>;
- };
- };
-
- du_pins: du {
- groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
- function = "du";
- };
-
- sdhi0_pins: sd0 {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <3300>;
- };
-
- sdhi0_pins_uhs: sd0_uhs {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <1800>;
- };
-
- sdhi2_pins: sd2 {
- groups = "sdhi2_data8", "sdhi2_ctrl";
- function = "sdhi2";
- power-source = <3300>;
- };
-
- sdhi2_pins_uhs: sd2_uhs {
- groups = "sdhi2_data8", "sdhi2_ctrl";
- function = "sdhi2";
- power-source = <1800>;
- };
-
- sdhi3_pins: sd3 {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <3300>;
- };
-
- sdhi3_pins_uhs: sd3_uhs {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <1800>;
- };
-
- sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
- function = "ssi";
- };
-
- sound_clk_pins: sound_clk {
- groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
- "audio_clkout_a", "audio_clkout3_a";
- function = "audio_clk";
- };
-
- usb0_pins: usb0 {
- groups = "usb0";
- function = "usb0";
- };
-
- usb1_pins: usb1 {
- mux {
- groups = "usb1";
- function = "usb1";
- };
-
- ovc {
- pins = "GP_6_27";
- bias-pull-up;
- };
-
- pwen {
- pins = "GP_6_26";
- bias-pull-down;
- };
- };
-
usb2_pins: usb2 {
groups = "usb2";
function = "usb2";
};
};
-&scif1 {
- pinctrl-0 = <&scif1_pins>;
- pinctrl-names = "default";
-
- uart-has-rtscts;
- status = "okay";
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&scif_clk {
- clock-frequency = <14745600>;
-};
-
-&i2c2 {
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-
- clock-frequency = <100000>;
-
- ak4613: codec@10 {
- compatible = "asahi-kasei,ak4613";
- #sound-dai-cells = <0>;
- reg = <0x10>;
- clocks = <&rcar_sound 3>;
-
- asahi-kasei,in1-single-end;
- asahi-kasei,in2-single-end;
- asahi-kasei,out1-single-end;
- asahi-kasei,out2-single-end;
- asahi-kasei,out3-single-end;
- asahi-kasei,out4-single-end;
- asahi-kasei,out5-single-end;
- asahi-kasei,out6-single-end;
- };
-
- cs2000: clk_multiplier@4f {
- #clock-cells = <0>;
- compatible = "cirrus,cs2000-cp";
- reg = <0x4f>;
- clocks = <&audio_clkout>, <&x12_clk>;
- clock-names = "clk_in", "ref_clk";
-
- assigned-clocks = <&cs2000>;
- assigned-clock-rates = <24576000>; /* 1/1 divide */
- };
-};
-
-&rcar_sound {
- pinctrl-0 = <&sound_pins &sound_clk_pins>;
- pinctrl-names = "default";
-
- /* Single DAI */
- #sound-dai-cells = <0>;
-
- /* audio_clkout0/1/2/3 */
- #clock-cells = <1>;
- clock-frequency = <11289600>;
-
- status = "okay";
-
- /* update <audio_clk_b> to <cs2000> */
- clocks = <&cpg CPG_MOD 1005>,
- <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
- <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
- <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
- <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
- <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
- <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
- <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
- <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
- <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
- <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
- <&audio_clk_a>, <&cs2000>,
- <&audio_clk_c>,
- <&cpg CPG_CORE R8A7795_CLK_S0D4>;
-
- rcar_sound,dai {
- dai0 {
- playback = <&ssi0 &src0 &dvc0>;
- capture = <&ssi1 &src1 &dvc1>;
- };
- };
-};
-
&sata {
status = "okay";
};
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-1 = <&sdhi0_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi0>;
- vqmmc-supply = <&vccq_sdhi0>;
- cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- status = "okay";
-};
-
-&sdhi2 {
- /* used for on-board 8bit eMMC */
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-1 = <&sdhi2_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- bus-width = <8>;
- mmc-hs200-1_8v;
- non-removable;
- status = "okay";
-};
-
-&sdhi3 {
- pinctrl-0 = <&sdhi3_pins>;
- pinctrl-1 = <&sdhi3_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi3>;
- vqmmc-supply = <&vccq_sdhi3>;
- cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- status = "okay";
-};
-
-&ssi1 {
- shared-pin;
-};
-
-&wdt0 {
- timeout-sec = <60>;
- status = "okay";
-};
-
-&audio_clk_a {
- clock-frequency = <22579200>;
-};
-
-&i2c_dvfs {
- status = "okay";
-};
-
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
- renesas,no-ether-link;
- phy-handle = <&phy0>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
-&xhci0 {
- status = "okay";
-};
-
-&usb2_phy0 {
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-
- vbus-supply = <&vbus0_usb2>;
- status = "okay";
-};
-
-&usb2_phy1 {
- pinctrl-0 = <&usb1_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
&usb2_phy2 {
pinctrl-0 = <&usb2_pins>;
pinctrl-names = "default";
status = "okay";
};
-
-&ehci0 {
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
-&ehci2 {
- status = "okay";
-};
-
-&ohci0 {
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};
-
-&ohci2 {
- status = "okay";
-};
-
-&hsusb {
- status = "okay";
-};
-
-&pcie_bus_clk {
- clock-frequency = <100000000>;
-};
-
-&pciec0 {
- status = "okay";
-};
-
-&pciec1 {
- status = "okay";
-};
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 31f02219ed2f..db4f162d6bdd 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -8,25 +8,16 @@
* kind, whether express or implied.
*/
+#define CPG_AUDIO_CLK_I R8A7796_CLK_S0D4
+
/dts-v1/;
#include "r8a7796.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-x.dtsi"
/ {
model = "Renesas Salvator-X board based on r8a7796";
compatible = "renesas,salvator-x", "renesas,r8a7796";
- aliases {
- serial0 = &scif2;
- serial1 = &scif1;
- ethernet0 = &avb;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
- stdout-path = "serial0:115200n8";
- };
-
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
@@ -37,248 +28,4 @@
device_type = "memory";
reg = <0x6 0x00000000 0x0 0x80000000>;
};
-
- reg_1p8v: regulator0 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator1 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- vcc_sdhi0: regulator-vcc-sdhi0 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi0: regulator-vccq-sdhi0 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI0 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
- };
-
- vcc_sdhi3: regulator-vcc-sdhi3 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI3 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi3: regulator-vccq-sdhi3 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI3 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1
- 1800000 0>;
- };
-};
-
-&pfc {
- pinctrl-0 = <&scif_clk_pins>;
- pinctrl-names = "default";
-
- avb_pins: avb {
- mux {
- groups = "avb_link", "avb_phy_int", "avb_mdc",
- "avb_mii";
- function = "avb";
- };
-
- pins_mdc {
- groups = "avb_mdc";
- drive-strength = <24>;
- };
-
- pins_mii_tx {
- pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
- "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
- drive-strength = <12>;
- };
- };
-
- scif1_pins: scif1 {
- groups = "scif1_data_a", "scif1_ctrl";
- function = "scif1";
- };
-
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
- };
- scif_clk_pins: scif_clk {
- groups = "scif_clk_a";
- function = "scif_clk";
- };
-
- i2c2_pins: i2c2 {
- groups = "i2c2_a";
- function = "i2c2";
- };
-
- sdhi0_pins: sd0 {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <3300>;
- };
-
- sdhi0_pins_uhs: sd0_uhs {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <1800>;
- };
-
- sdhi2_pins: sd2 {
- groups = "sdhi2_data8", "sdhi2_ctrl";
- function = "sdhi2";
- power-source = <3300>;
- };
-
- sdhi2_pins_uhs: sd2_uhs {
- groups = "sdhi2_data8", "sdhi2_ctrl";
- function = "sdhi2";
- power-source = <1800>;
- };
-
- sdhi3_pins: sd3 {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <3300>;
- };
-
- sdhi3_pins_uhs: sd3_uhs {
- groups = "sdhi3_data4", "sdhi3_ctrl";
- function = "sdhi3";
- power-source = <1800>;
- };
-};
-
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
- renesas,no-ether-link;
- phy-handle = <&phy0>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
-&extal_clk {
- clock-frequency = <16666666>;
-};
-
-&extalr_clk {
- clock-frequency = <32768>;
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-1 = <&sdhi0_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi0>;
- vqmmc-supply = <&vccq_sdhi0>;
- cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- status = "okay";
-};
-
-&sdhi2 {
- /* used for on-board 8bit eMMC */
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-1 = <&sdhi2_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- bus-width = <8>;
- mmc-hs200-1_8v;
- non-removable;
- status = "okay";
-};
-
-&sdhi3 {
- pinctrl-0 = <&sdhi3_pins>;
- pinctrl-1 = <&sdhi3_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi3>;
- vqmmc-supply = <&vccq_sdhi3>;
- cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- status = "okay";
-};
-
-&scif1 {
- pinctrl-0 = <&scif1_pins>;
- pinctrl-names = "default";
-
- uart-has-rtscts;
- status = "okay";
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&scif_clk {
- clock-frequency = <14745600>;
-};
-
-&i2c2 {
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&wdt0 {
- timeout-sec = <60>;
- status = "okay";
-};
-
-&i2c_dvfs {
- status = "okay";
};
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
new file mode 100644
index 000000000000..47a482f20c9d
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -0,0 +1,555 @@
+/*
+ * Device Tree Source for the Salvator-X board
+ *
+ * Copyright (C) 2015-2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/*
+ * SSI-AK4613
+ *
+ * This command is required when Playback/Capture
+ *
+ * amixer set "DVC Out" 100%
+ * amixer set "DVC In" 100%
+ *
+ * You can use Mute
+ *
+ * amixer set "DVC Out Mute" on
+ * amixer set "DVC In Mute" on
+ *
+ * You can use Volume Ramp
+ *
+ * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
+ * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
+ * amixer set "DVC Out Ramp" on
+ * aplay xxx.wav &
+ * amixer set "DVC Out" 80% // Volume Down
+ * amixer set "DVC Out" 100% // Volume Up
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Renesas Salvator-X board";
+ compatible = "renesas,salvator-x";
+
+ aliases {
+ serial0 = &scif2;
+ serial1 = &scif1;
+ ethernet0 = &avb;
+ };
+
+ chosen {
+ bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+ stdout-path = "serial0:115200n8";
+ };
+
+ audio_clkout: audio_clkout {
+ /*
+ * This is same as <&rcar_sound 0>
+ * but needed to avoid cs2000/rcar_sound probe dead-lock
+ */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <11289600>;
+ };
+
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ rsnd_ak4613: sound {
+ compatible = "simple-audio-card";
+
+ simple-audio-card,format = "left_j";
+ simple-audio-card,bitclock-master = <&sndcpu>;
+ simple-audio-card,frame-master = <&sndcpu>;
+
+ sndcpu: simple-audio-card,cpu {
+ sound-dai = <&rcar_sound>;
+ };
+
+ sndcodec: simple-audio-card,codec {
+ sound-dai = <&ak4613>;
+ };
+ };
+
+ vbus0_usb2: regulator-vbus0-usb2 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB20_VBUS0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vcc_sdhi3: regulator-vcc-sdhi3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI3 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi3: regulator-vccq-sdhi3 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI3 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vga {
+ compatible = "vga-connector";
+
+ port {
+ vga_in: endpoint {
+ remote-endpoint = <&adv7123_out>;
+ };
+ };
+ };
+
+ vga-encoder {
+ compatible = "adi,adv7123";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7123_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ adv7123_out: endpoint {
+ remote-endpoint = <&vga_in>;
+ };
+ };
+ };
+ };
+
+ x12_clk: x12 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+};
+
+&audio_clk_a {
+ clock-frequency = <22579200>;
+};
+
+&avb {
+ pinctrl-0 = <&avb_pins>;
+ pinctrl-names = "default";
+ renesas,no-ether-link;
+ phy-handle = <&phy0>;
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ rxc-skew-ps = <1500>;
+ reg = <0>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&du {
+ pinctrl-0 = <&du_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ ports {
+ port@0 {
+ endpoint {
+ remote-endpoint = <&adv7123_in>;
+ };
+ };
+ port@3 {
+ lvds_connector: endpoint {
+ };
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&extal_clk {
+ clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+ clock-frequency = <32768>;
+};
+
+&hsusb {
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ clock-frequency = <100000>;
+
+ ak4613: codec@10 {
+ compatible = "asahi-kasei,ak4613";
+ #sound-dai-cells = <0>;
+ reg = <0x10>;
+ clocks = <&rcar_sound 3>;
+
+ asahi-kasei,in1-single-end;
+ asahi-kasei,in2-single-end;
+ asahi-kasei,out1-single-end;
+ asahi-kasei,out2-single-end;
+ asahi-kasei,out3-single-end;
+ asahi-kasei,out4-single-end;
+ asahi-kasei,out5-single-end;
+ asahi-kasei,out6-single-end;
+ };
+
+ cs2000: clk_multiplier@4f {
+ #clock-cells = <0>;
+ compatible = "cirrus,cs2000-cp";
+ reg = <0x4f>;
+ clocks = <&audio_clkout>, <&x12_clk>;
+ clock-names = "clk_in", "ref_clk";
+
+ assigned-clocks = <&cs2000>;
+ assigned-clock-rates = <24576000>; /* 1/1 divide */
+ };
+};
+
+&i2c_dvfs {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pcie_bus_clk {
+ clock-frequency = <100000000>;
+};
+
+&pciec0 {
+ status = "okay";
+};
+
+&pciec1 {
+ status = "okay";
+};
+
+&pfc {
+ pinctrl-0 = <&scif_clk_pins>;
+ pinctrl-names = "default";
+
+ avb_pins: avb {
+ mux {
+ groups = "avb_link", "avb_phy_int", "avb_mdc",
+ "avb_mii";
+ function = "avb";
+ };
+
+ pins_mdc {
+ groups = "avb_mdc";
+ drive-strength = <24>;
+ };
+
+ pins_mii_tx {
+ pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+ "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+ drive-strength = <12>;
+ };
+ };
+
+ du_pins: du {
+ groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
+ function = "du";
+ };
+
+ i2c2_pins: i2c2 {
+ groups = "i2c2_a";
+ function = "i2c2";
+ };
+
+ scif1_pins: scif1 {
+ groups = "scif1_data_a", "scif1_ctrl";
+ function = "scif1";
+ };
+
+ scif2_pins: scif2 {
+ groups = "scif2_data_a";
+ function = "scif2";
+ };
+
+ scif_clk_pins: scif_clk {
+ groups = "scif_clk_a";
+ function = "scif_clk";
+ };
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
+ };
+
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
+ sdhi3_pins: sd3 {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
+ };
+
+ sound_pins: sound {
+ groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+ function = "ssi";
+ };
+
+ sound_clk_pins: sound_clk {
+ groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+ "audio_clkout_a", "audio_clkout3_a";
+ function = "audio_clk";
+ };
+
+ usb0_pins: usb0 {
+ groups = "usb0";
+ function = "usb0";
+ };
+
+ usb1_pins: usb1 {
+ mux {
+ groups = "usb1";
+ function = "usb1";
+ };
+
+ ovc {
+ pins = "GP_6_27";
+ bias-pull-up;
+ };
+
+ pwen {
+ pins = "GP_6_26";
+ bias-pull-down;
+ };
+ };
+};
+
+&rcar_sound {
+ pinctrl-0 = <&sound_pins &sound_clk_pins>;
+ pinctrl-names = "default";
+
+ /* Single DAI */
+ #sound-dai-cells = <0>;
+
+ /* audio_clkout0/1/2/3 */
+ #clock-cells = <1>;
+ clock-frequency = <11289600>;
+
+ status = "okay";
+
+ /* update <audio_clk_b> to <cs2000> */
+ clocks = <&cpg CPG_MOD 1005>,
+ <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+ <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+ <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+ <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+ <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+ <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+ <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+ <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+ <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+ <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+ <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+ <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+ <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+ <&audio_clk_a>, <&cs2000>,
+ <&audio_clk_c>,
+ <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+
+ rcar_sound,dai {
+ dai0 {
+ playback = <&ssi0 &src0 &dvc0>;
+ capture = <&ssi1 &src1 &dvc1>;
+ };
+ };
+};
+
+&scif1 {
+ pinctrl-0 = <&scif1_pins>;
+ pinctrl-names = "default";
+
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&scif2 {
+ pinctrl-0 = <&scif2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&scif_clk {
+ clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ status = "okay";
+};
+
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ status = "okay";
+};
+
+&sdhi3 {
+ pinctrl-0 = <&sdhi3_pins>;
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <&vcc_sdhi3>;
+ vqmmc-supply = <&vccq_sdhi3>;
+ cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ status = "okay";
+};
+
+&ssi1 {
+ shared-pin;
+};
+
+&usb2_phy0 {
+ pinctrl-0 = <&usb0_pins>;
+ pinctrl-names = "default";
+
+ vbus-supply = <&vbus0_usb2>;
+ status = "okay";
+};
+
+&usb2_phy1 {
+ pinctrl-0 = <&usb1_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&wdt0 {
+ timeout-sec = <60>;
+ status = "okay";
+};
+
+&xhci0 {
+ status = "okay";
+};
--
2.1.4
