Hi Jagan
@@ -1503,28 +1506,18 @@ static int samsung_dsim_panel_or_bridge(struct
samsung_dsim *dsi,
{
struct drm_bridge *panel_bridge;
struct drm_panel *panel;
- struct device_node *remote;
-
- if (of_graph_is_present(node)) {
- remote = of_graph_get_remote_node(node, DSI_PORT_OUT, 0);
- if (!remote)
- return -ENODEV;
+ int ret;
- node = remote;
- }
+ ret = drm_of_find_panel_or_bridge(dsi->dev->of_node, 1, 0, &panel,
+ &panel_bridge);
+ if (ret)
+ return ret;
- panel_bridge = of_drm_find_bridge(node);
- if (!panel_bridge) {
- panel = of_drm_find_panel(node);
- if (!IS_ERR(panel)) {
- panel_bridge = drm_panel_bridge_add(panel);
- if (IS_ERR(panel_bridge))
- return PTR_ERR(panel_bridge);
- }
+ if (panel) {
+ panel_bridge = drm_panel_bridge_add(panel);
+ if (IS_ERR(panel_bridge))
+ return PTR_ERR(panel_bridge);
}
-
- of_node_put(node);
-
dsi->out_bridge = panel_bridge;
I need to apply this change to register my panel on imx8mn even mode I
found that
@@ -1594,11 +1587,15 @@ static int samsung_dsim_host_attach(struct
mipi_dsi_host *host,
return ret;
}
- mutex_lock(&drm->mode_config.mutex);
dsi->lanes = device->lanes;
dsi->format = device->format;
dsi->mode_flags = device->mode_flags;
+
+ if (!drm)
+ return 0;
+
+ mutex_lock(&drm->mode_config.mutex);
mode_config is not initialized in this path.
Michael
On Tue, Nov 30, 2021 at 8:39 AM Jagan Teki <ja...@amarulasolutions.com> wrote:
>
> On Fri, Nov 26, 2021 at 9:34 PM Maxime Ripard <max...@cerno.tech> wrote:
> >
> > On Thu, Nov 25, 2021 at 09:44:14PM +0530, Jagan Teki wrote:
> > > On Thu, Nov 25, 2021 at 9:40 PM Maxime Ripard <max...@cerno.tech> wrote:
> > > >
> > > > On Thu, Nov 25, 2021 at 07:55:41PM +0530, Jagan Teki wrote:
> > > > > Hi,
> > > > >
> > > > > On Thu, Nov 25, 2021 at 7:45 PM Maxime Ripard <max...@cerno.tech>
> > > > > wrote:
> > > > > >
> > > > > > On Wed, Nov 24, 2021 at 12:02:47AM +0530, Jagan Teki wrote:
> > > > > > > > > > > > + dsi->panel = of_drm_find_panel(remote);
> > > > > > > > > > > > + if (IS_ERR(dsi->panel)) {
> > > > > > > > > > > > + dsi->panel = NULL;
> > > > > > > > > > > > +
> > > > > > > > > > > > + dsi->next_bridge =
> > > > > > > > > > > > of_drm_find_bridge(remote);
> > > > > > > > > > > > + if (IS_ERR(dsi->next_bridge)) {
> > > > > > > > > > > > + dev_err(dsi->dev, "failed to find
> > > > > > > > > > > > bridge\n");
> > > > > > > > > > > > + return PTR_ERR(dsi->next_bridge);
> > > > > > > > > > > > + }
> > > > > > > > > > > > + } else {
> > > > > > > > > > > > + dsi->next_bridge = NULL;
> > > > > > > > > > > > + }
> > > > > > > > > > > > +
> > > > > > > > > > > > + of_node_put(remote);
> > > > > > > > > > >
> > > > > > > > > > > Using devm_drm_of_get_bridge would greatly simplify the
> > > > > > > > > > > driver
> > > > > > > > > >
> > > > > > > > > > I'm aware of this and this would break the existing sunxi
> > > > > > > > > > dsi binding,
> > > > > > > > > > we are not using ports based pipeline in dsi node.
> > > > > > > > > > Of-course you have
> > > > > > > > > > pointed the same before, please check below
> > > > > > > > > > https://patchwork.kernel.org/project/dri-devel/patch/20210322140152.101709-2-ja...@amarulasolutions.com/
> > > > > > > > >
> > > > > > > > > Then drm_of_find_panel_or_bridge needs to be adjusted to
> > > > > > > > > handle the DSI
> > > > > > > > > bindings and look for a panel or bridge not only through the
> > > > > > > > > OF graph,
> > > > > > > > > but also on the child nodes
> > > > > > > >
> > > > > > > > Okay. I need to check this.
> > > > > > >
> > > > > > > devm_drm_of_get_bridge is not working with legacy binding like
> > > > > > > the one
> > > > > > > used in sun6i dsi
> > > > > >
> > > > > > There's nothing legacy about it.
> > > > >
> > > > > What I'm mean legacy here with current binding used in sun6i-dsi like
> > > > > this.
> > > > >
> > > > > &dsi {
> > > > > vcc-dsi-supply = <®_dcdc1>; /* VCC-DSI */
> > > > > status = "okay";
> > > > >
> > > > > panel@0 {
> > > > > compatible = "bananapi,s070wv20-ct16-icn6211";
> > > > > reg = <0>;
> > > > > reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /*
> > > > > LCD-RST: PL5 */
> > > > > enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /*
> > > > > LCD-PWR-EN: PB7 */
> > > > > backlight = <&backlight>;
> > > > > };
> > > > > };
> > > >
> > > > Yes, I know, it's the generic DSI binding. It's still not legacy.
> > > >
> > > > > devm_drm_of_get_bridge cannot find the device with above binding and
> > > > > able to find the device with below binding.
> > > > >
> > > > > &dsi {
> > > > > vcc-dsi-supply = <®_dcdc1>; /* VCC-DSI */
> > > > > status = "okay";
> > > > >
> > > > > ports {
> > > > > #address-cells = <1>;
> > > > > #size-cells = <0>;
> > > > >
> > > > > dsi_out: port@0 {
> > > > > reg = <0>;
> > > > >
> > > > > dsi_out_bridge: endpoint {
> > > > > remote-endpoint = <&bridge_out_dsi>;
> > > > > };
> > > > > };
> > > > > };
> > > > >
> > > > > panel@0 {
> > > > > compatible = "bananapi,s070wv20-ct16-icn6211";
> > > > > reg = <0>;
> > > > > reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST:
> > > > > PL5 */
> > > > > enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /*
> > > > > LCD-PWR-EN: PB7 */
> > > > > backlight = <&backlight>;
> > > > >
> > > > > port {
> > > > > bridge_out_dsi: endpoint {
> > > > > remote-endpoint = <&dsi_out_bridge>;
> > > > > };
> > > > > };
> > > > > };
> > > > > };
> > > >
> > > > Yes, I know, and that's because ...
> > >
> > > Okay. I will use find panel and bridge separately instead of
> > > devm_drm_of_get_bridge in version patches.
> >
> > That's not been my point, at all?
> >
> > I mean, that whole discussion has been because you shouldn't do that.
> >
> > > >
> > > > > >
> > > > > > > https://patchwork.kernel.org/project/dri-devel/patch/20211122065223.88059-6-ja...@amarulasolutions.com/
> > > > > > >
> > > > > > > dsi->next_bridge = devm_drm_of_get_bridge(dsi->dev,
> > > > > > > dsi->dev->of_node, 0, 0);
> > > > > > > if (IS_ERR(dsi->next_bridge))
> > > > > > > return PTR_ERR(dsi->next_bridge);
> > > > > > >
> > > > > > > It is only working if we have ports on the pipeline, something
> > > > > > > like this
> > > > > > > https://patchwork.kernel.org/project/dri-devel/patch/20210214194102.126146-8-ja...@amarulasolutions.com/
> > > > > > >
> > > > > > > Please have a look and let me know if I miss anything?
> > > > > >
> > > > > > Yes, you're missing the answer you quoted earlier:
> > > > >
> > > > > Yes, I'm trying to resolve the comment one after another. Will get
> > > > > back.
> > > >
> > > > ... You've ignored that comment.
> > >
> > > Not understand which comment you mean. There are few about bridge
> > > conversion details, I will send my comments.
> >
> > The one that got quoted there and you removed. For reference:
> >
> > > Then drm_of_find_panel_or_bridge needs to be adjusted to handle the DSI
> > > bindings and look for a panel or bridge not only through the OF graph,
> > > but also on the child nodes
> >
> > devm_drm_of_get_bridge uses drm_of_find_panel_or_bridge under the hood,
> > so of course it won't find it if drm_of_find_panel_or_bridge doesn't.
> > You need to modify drm_of_find_panel_or_bridge to also look for child
> > devices and see if there's a panel or bridge registered for that child
> > node. Then devm_drm_of_get_bridge will work as you intend it to.
>
> Got it now, I will make necessary changes.
>
> Thanks,
> Jagan.
>
>
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
mich...@amarulasolutions.com
__________________________________
Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
i...@amarulasolutions.com
www.amarulasolutions.com
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
To view this discussion on the web, visit
https://groups.google.com/d/msgid/linux-sunxi/CAOf5uw%3DQF7XMbYT4pyZBTTO87TRLzVmYH2HvX%3DjCg_QpNGN1LA%40mail.gmail.com.
