I just recompiled the ohci and ehci drivers as modules, and now it's consistently freezing at random places.
On Saturday, March 8, 2014 11:54:25 AM UTC-6, Matthew Schneider wrote: > > I had the problem as well where it wasn't able to locate the firmware and > seemed to hang up on that. So I compiled the firmware into the kernel, but > then it hung on the message "rtlwifi: wireless switch is on". So then I > took the wireless device drivers out the kernel entirely (since I don't > really need them), which leaves me with my original post. > > On Saturday, March 8, 2014 7:48:49 AM UTC-6, CodeKipper wrote: >> >> Hi, >> I'm also currently battling suxi-devel on my Mele A2000. I'm getting a >> little bit further than you but not by a great deal. Here is my .config >> which I took from Hans. There are a couple of differences to get the >> wireless bits compiled into the uImage. The rootfs I've been using is >> Debian(which doesn't seem to locate the firmware) and in >> http://pastebin.com/XNVxf03B which is the openwrt rootfs which does load >> the firmware and then seems to hang. >> Good luck with this, I can't play anymore today but let's us know if you >> get any further. >> CK >> >> >> On 8 March 2014 08:56, Matthew Schneider <matthewaar...@gmail.com> wrote: >> >>> My mele a1000 hangs on boot using the sunxi-devel kernel tree. >>> >>> It seems like it'll sometimes hang at different places, but most of the >>> time it'll hang at "usb 2-1: new high-speed USB device number 2 using >>> ehci-platform". >>> >>> I've attached my kernel configuration. >>> >>> Here's the last screen my console showed: >>> >>> >>> [ 0.857803] ehci-platform 1c1c000.usb: EHCI Host Controller >>> [ 0.863428] ehci-platform 1c1c000.usb: new USB bus registered, >>> assigned bus number 2 >>> [ 0.871240] ehci-platform 1c1c000.usb: irq 22, io mem 0x01c1c000 >>> [ 0.893010] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 >>> [ 0.899687] hub 2-0:1.0: USB hub found >>> [ 0.903476] hub 2-0:1.0: 1 port detected >>> [ 0.907701] ohci-platform 1c14400.usb: Generic Platform OHCI >>> controller >>> [ 0.914369] ohci-platform 1c14400.usb: new USB bus registered, >>> assigned bus number 3 >>> [ 0.922149] ohci-platform 1c14400.usb: irq 20, io mem 0x01c14400 >>> [ 0.953049] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >>> [ 0.965526] ata1.00: ATA-8: ST1000LM024 HN-M101MBB, 2AR10002, max >>> UDMA/133 >>> [ 0.972396] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth >>> 31/32) >>> [ 0.987092] ata1.00: configured for UDMA/133 >>> [ 0.991950] hub 3-0:1.0: USB hub found >>> [ 0.995759] hub 3-0:1.0: 1 port detected >>> [ 1.000015] ohci-platform 1c1c400.usb: Generic Platform OHCI >>> controller >>> [ 1.008000] scsi 0:0:0:0: Direct-Access ATA ST1000LM024 HN-M >>> 2AR1 PQ: 0 ANSI: 5 >>> [ 1.017164] ohci-platform 1c1c400.usb: new USB bus registered, >>> assigned bus number 4 >>> [ 1.025424] ohci-platform 1c1c400.usb: irq 23, io mem 0x01c1c400 >>> [ 1.087535] hub 4-0:1.0: USB hub found >>> [ 1.091308] hub 4-0:1.0: 1 port detected >>> [ 1.095522] sunxi-rtc 1c20d00.rtc: setting system clock to 2010-01-01 >>> 00:01:57 UTC (1262304117) >>> [ 1.104382] ALSA device list: >>> [ 1.107366] No soundcards found. >>> [ 1.111339] Waiting for root device /dev/mmcblk0p2... >>> [ 1.123224] mmc0: host does not support reading read-only switch. >>> assuming write-enable. >>> [ 1.173033] usb 1-1: new high-speed USB device number 2 using >>> ehci-platform >>> [ 1.293012] mmc0: new high speed SDHC card at address e624 >>> [ 1.298821] mmcblk0: mmc0:e624 SU16G 14.8 GiB >>> [ 1.305399] mmcblk0: p1 p2 >>> [ 1.335541] hub 1-1:1.0: USB hub found >>> [ 1.339632] hub 1-1:1.0: 4 ports detected >>> [ 1.347376] EXT3-fs (mmcblk0p2): error: couldn't mount because of >>> unsupported optional features (240) >>> [ 1.357364] EXT2-fs (mmcblk0p2): error: couldn't mount because of >>> unsupported optional features (240) >>> [ 1.463026] usb 2-1: new high-speed USB device number 2 using >>> ehci-platform >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "linux-sunxi" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to linux-sunxi...@googlegroups.com. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.