Actually, I take that back. It seems to be freezing at this point: http://pastebin.com/JXj1cHHD
On Saturday, March 8, 2014 12:12:48 PM UTC-6, Matthew Schneider wrote: > > I just recompiled the ohci and ehci drivers as modules, and now it's > consistently freezing at random places. > > On Saturday, March 8, 2014 11:54:25 AM UTC-6, Matthew Schneider wrote: >> >> I had the problem as well where it wasn't able to locate the firmware and >> seemed to hang up on that. So I compiled the firmware into the kernel, but >> then it hung on the message "rtlwifi: wireless switch is on". So then I >> took the wireless device drivers out the kernel entirely (since I don't >> really need them), which leaves me with my original post. >> >> On Saturday, March 8, 2014 7:48:49 AM UTC-6, CodeKipper wrote: >>> >>> Hi, >>> I'm also currently battling suxi-devel on my Mele A2000. I'm getting a >>> little bit further than you but not by a great deal. Here is my .config >>> which I took from Hans. There are a couple of differences to get the >>> wireless bits compiled into the uImage. The rootfs I've been using is >>> Debian(which doesn't seem to locate the firmware) and in >>> http://pastebin.com/XNVxf03B which is the openwrt rootfs which does >>> load the firmware and then seems to hang. >>> Good luck with this, I can't play anymore today but let's us know if you >>> get any further. >>> CK >>> >>> >>> On 8 March 2014 08:56, Matthew Schneider <matthewaar...@gmail.com>wrote: >>> >>>> My mele a1000 hangs on boot using the sunxi-devel kernel tree. >>>> >>>> It seems like it'll sometimes hang at different places, but most of the >>>> time it'll hang at "usb 2-1: new high-speed USB device number 2 using >>>> ehci-platform". >>>> >>>> I've attached my kernel configuration. >>>> >>>> Here's the last screen my console showed: >>>> >>>> >>>> [ 0.857803] ehci-platform 1c1c000.usb: EHCI Host Controller >>>> [ 0.863428] ehci-platform 1c1c000.usb: new USB bus registered, >>>> assigned bus number 2 >>>> [ 0.871240] ehci-platform 1c1c000.usb: irq 22, io mem 0x01c1c000 >>>> [ 0.893010] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 >>>> [ 0.899687] hub 2-0:1.0: USB hub found >>>> [ 0.903476] hub 2-0:1.0: 1 port detected >>>> [ 0.907701] ohci-platform 1c14400.usb: Generic Platform OHCI >>>> controller >>>> [ 0.914369] ohci-platform 1c14400.usb: new USB bus registered, >>>> assigned bus number 3 >>>> [ 0.922149] ohci-platform 1c14400.usb: irq 20, io mem 0x01c14400 >>>> [ 0.953049] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >>>> [ 0.965526] ata1.00: ATA-8: ST1000LM024 HN-M101MBB, 2AR10002, max >>>> UDMA/133 >>>> [ 0.972396] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth >>>> 31/32) >>>> [ 0.987092] ata1.00: configured for UDMA/133 >>>> [ 0.991950] hub 3-0:1.0: USB hub found >>>> [ 0.995759] hub 3-0:1.0: 1 port detected >>>> [ 1.000015] ohci-platform 1c1c400.usb: Generic Platform OHCI >>>> controller >>>> [ 1.008000] scsi 0:0:0:0: Direct-Access ATA ST1000LM024 >>>> HN-M 2AR1 PQ: 0 ANSI: 5 >>>> [ 1.017164] ohci-platform 1c1c400.usb: new USB bus registered, >>>> assigned bus number 4 >>>> [ 1.025424] ohci-platform 1c1c400.usb: irq 23, io mem 0x01c1c400 >>>> [ 1.087535] hub 4-0:1.0: USB hub found >>>> [ 1.091308] hub 4-0:1.0: 1 port detected >>>> [ 1.095522] sunxi-rtc 1c20d00.rtc: setting system clock to >>>> 2010-01-01 00:01:57 UTC (1262304117) >>>> [ 1.104382] ALSA device list: >>>> [ 1.107366] No soundcards found. >>>> [ 1.111339] Waiting for root device /dev/mmcblk0p2... >>>> [ 1.123224] mmc0: host does not support reading read-only switch. >>>> assuming write-enable. >>>> [ 1.173033] usb 1-1: new high-speed USB device number 2 using >>>> ehci-platform >>>> [ 1.293012] mmc0: new high speed SDHC card at address e624 >>>> [ 1.298821] mmcblk0: mmc0:e624 SU16G 14.8 GiB >>>> [ 1.305399] mmcblk0: p1 p2 >>>> [ 1.335541] hub 1-1:1.0: USB hub found >>>> [ 1.339632] hub 1-1:1.0: 4 ports detected >>>> [ 1.347376] EXT3-fs (mmcblk0p2): error: couldn't mount because of >>>> unsupported optional features (240) >>>> [ 1.357364] EXT2-fs (mmcblk0p2): error: couldn't mount because of >>>> unsupported optional features (240) >>>> [ 1.463026] usb 2-1: new high-speed USB device number 2 using >>>> ehci-platform >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "linux-sunxi" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to linux-sunxi...@googlegroups.com. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.