在 2017-07-20 10:03,icen...@aosc.io 写道:
在 2017-07-20 06:59,Ondřej Jirman 写道:
Hi,
Icenowy Zheng píše v Út 04. 04. 2017 v 17:50 +0800:
From: Icenowy Zheng <icen...@aosc.xyz>
Now we have driver for the PRCM CCU, switch to use it instead of
old-style clock nodes for apb0-related clocks in sunxi-h3-h5.dtsi .
The mux 3 of R_CCU is still the internal oscillator, which is said to
be
16MHz plus minus 30%, and get a measured value of 15MHz~16MHz on my
two
H3 boards and one H5 board.
There's issue with the new r_ccu that breaks r_i2c. (no devices can be
found on the bus). Reverting this patch fixes the issue with the I2C
controller. (everything else being the same)
Here's the code I'm using:
https://github.com/megous/linux/commits/oran
ge-pi-4.12
The last commit is the revert.
The issue manifests itself by non-working DVFS, because kernel lacks
access to SY8106A regulator, because r_i2c doesn't work with sunxi-ng
clock driver (sun8i-r).
Relevant difference in registers between working/non-working state is
just this (diff -u):
0x01f02400 = 0x00000000
0x01f02404 = 0x00000000
-0x01f02408 = 0x00000091
+0x01f02408 = 0x00000095 DATA register inisde the I2C controller
0x01f0240c = 0x00000044
0x01f02410 = 0x000000f8
-0x01f02414 = 0x00000059
+0x01f02414 = 0x00000000 CLOCK setup register inside the I2C
controller
0x01f02418 = 0x00000000
0x01f0241c = 0x00000000
0x01f02420 = 0x0000003a
It looks like the new sunxi-ng clock driver causes the I2C driver to
not correctly configure the CLOCK register. I don't know why and I'm
not sure how to deal with this. Any ideas what can I do next?
thank you and regards,
o.
It seems to be a very very very weird problem -- the CPUS_CFG register
seems to be not accessible in non-secure mode on H3, and if the r_ccu
driver reads it a value of 0x0 is read out (which means that the parent
of ar100 is osc32k), but the real initial value of the register is
0x00010000 (which means the parent is osc24M).
So the bus clock of r_i2c is wrongly claimed as 32kHz, not 24MHz, then
the r_i2c fails to work.
The protection to AR100 registers can be removed by writing 1 to
0x01f015d0
(0x1d0 at PRCM memory region).
Interestingly this controlling register can be written in non-secure
world,
so it's still broken secure/non-secure division ;-)
This clock problem doesn't exist for A64.
Signed-off-by: Icenowy Zheng <icen...@aosc.xyz>
---
Changes in v4:
- Temporarily dropped the CCU headers.
Changes in v3:
- Change osc32000 to iosc.
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 45
++++++++++++--------------------------
1 file changed, 14 insertions(+), 31 deletions(-)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 6640ebfa6419..1aeeacb3a884 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -68,31 +68,12 @@
clock-output-names = "osc32k";
};
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
+ iosc: internal-osc-clk {
#clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
+ compatible = "fixed-clock";
+ clock-frequency = <16000000>;
+ clock-accuracy = <300000000>;
+ clock-output-names = "iosc";
};
};
@@ -576,9 +557,12 @@
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
+ r_ccu: clock@1f01400 {
+ compatible = "allwinner,sun50i-a64-r-ccu";
+ reg = <0x01f01400 0x100>;
+ clocks = <&osc24M>, <&osc32k>, <&iosc>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
#reset-cells = <1>;
};
@@ -589,9 +573,9 @@
ir: ir@01f02000 {
compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
+ clocks = <&r_ccu 4>, <&r_ccu 11>;
clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
+ resets = <&r_ccu 0>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01f02000 0x40>;
status = "disabled";
@@ -601,9 +585,8 @@
compatible = "allwinner,sun8i-h3-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clocks = <&r_ccu 3>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
--
2.12.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-ker...@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
_______________________________________________
linux-arm-kernel mailing list
linux-arm-ker...@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.