Attacched you have my complete debug.syslog file since the sistem boot: Here i gibe also de complete dmesg relating to USB:
uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: detected 2 ports
uhci_hcd 0000:00:07.2: check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:07.2: Performing full reset
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00003400
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Intel Corporation 82371AB/EB/MB PIIX4 USB
usb usb1: Manufacturer: Linux 2.6.13 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0000
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for
USB modems and ISDN adapters
uhci_hcd 0000:00:07.2: wakeup_rh (auto-start)
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:07.2: port 1 portsc 0093,00
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
cdc_acm 1-1:1.0: usb_probe_interface
cdc_acm 1-1:1.0: usb_probe_interface - got id
cdc_acm 1-1:1.0: ttyACM0: USB ACM device
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002
BlackDeath:{root}:/usr/src/linux>minicom
LANG/ja
LANG/ko
LANG/ru
LC_ALL/ja
LC_ALL/ko
LC_ALL/ru
minicom: cannot open /dev/usb/ttyACM0: Input/output error
On Thu, September 1, 2005 23:44, Oliver Neukum wrote:
> Am Donnerstag, 1. September 2005 23:32 schrieb Luigi Genoni:
>
>> does not work properly.
>>
>> it seems to attach the device to /dev/usb/ttyACM0 as dmesg shows,
>>
>> usbcore: registered new driver cdc_acm
>> drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for
>> USB modems and ISDN adapters
>> usb 1-1: new full speed USB device using uhci_hcd and address 13 cdc_acm
>> 1-1:1.0: ttyACM0: USB ACM device
>>
>>
>> but then pppd has problems, so trying to access the modem via
>> minicom...
>
> Recompile with debugging and post the syslog. This is not enough
> to say anything intellegent about that.
>
> Regards
> Oliver
>
>
debug.syslog
Description: Binary data
