Hi again,
Thanks for the quick reply!
lsmod shows aic7xxx loaded ..... what might be missing and how should I
approach it?
PeterB
On Friday 21 June 2002 14:26, Stephen J. Gowdy wrote:
> It is trying to load the SCSI CDROM module and failing which suggests you
> don't have SCSI built fully for your kernel.
>
> On Fri, 21 Jun 2002, Peter B Van Campn wrote:
> > Dear USB-List,
> >
> > I'm new to USB and I seem to have a Linux prob recognising a USB Key
> > Drive. This devise works ok on WinXP; it pops up as a removeable hard
> > drive and I can write to it and read it.
> >
> > When I plug it in on SuSE 8.0 there is a reassuring 'beep' from the
> > system, but the device does not show up for mounting. I have looked at
> > many articles and FAQs about this but despite the fact that all kernal
> > msgs etc show USB and device detected it does NOT show up in fdisk -l
> >
> > There should be a /dev/sdx type entry but it is missing.
> >
> > The modules seem to load ok, they seem to detect the device.
> >
> > I have appended the relevent lines from boot.log and messages.
> >
> > Can anyone help me get this working? I would appreciate any help offered!
> >
> > PeterB
> >
> > USB Key Drive 128 MB
> >
> > lsmod shows:
> > usb-storage 48416 0
> > usb-uhci 21988 0 (unused)
> > usbcore 57184 1 [usb-storage usb-uhci]
> >
> > In /var/log/boot.msg
> > <6>usb.c: registered new driver usbdevfs
> > <6>usb.c: registered new driver hub
> > <6>usb-uhci.c: $Revision: 1.275 $ time 14:22:59 Mar 27 2002
> > <6>usb-uhci.c: High bandwidth mode enabled
> > <6>usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 14
> > <4>usb-uhci.c: Detected 2 ports
> > <6>usb.c: new USB bus registered, assigned bus number 1
> > <6>hub.c: USB hub found
> > <6>hub.c: 2 ports detected
> > <6>usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 14
> > <4>usb-uhci.c: Detected 2 ports
> > <6>usb.c: new USB bus registered, assigned bus number 2
> > <6>hub.c: USB hub found
> > <6>hub.c: 2 ports detected
> > <6>usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
> > <6>hub.c: USB new device connect on bus1/1, assigned device number 2
> > <4>usb.c: USB device 2 (vend/prod 0xaec/0x5010) is not claimed by any
> > active driver.
> >
> > usbdevfs on /proc/bus/usb type usbdevfs (rw)
> > <notice>/etc/init.d/rc5.d/S07hotplug start
> > Starting hotplugging services [ net pci usb^G ]
> > done
> >
> > In /var/log/messages
> > Jun 20 22:46:58 linux kernel: Initializing USB Mass Storage driver...
> > Jun 20 22:46:58 linux kernel: usb.c: registered new driver usb-storage
> > Jun 20 22:46:58 linux kernel: scsi2 : SCSI emulation for USB Mass Storage
> > devices
> > Jun 20 22:46:58 linux kernel: WARNING: USB Mass Storage data integrity
> > not assured
> > Jun 20 22:46:58 linux kernel: USB Mass Storage device found at 2
> > Jun 20 22:46:58 linux kernel: USB Mass Storage support registered.
> >
> > Jun 20 23:10:10 linux kernel: usb.c: USB disconnect on device 2
> > Jun 20 23:10:10 linux modprobe: modprobe: Can't locate module
> > block-major-11 Jun 20 23:10:11 linux last message repeated 15 times
> > Jun 20 23:10:11 linux /etc/hotplug/usb.agent[1513]: Can't ignore signal
> > CHLD, forcing to default.
> > Jun 20 23:10:16 linux kernel: hub.c: USB new device connect on bus1/1,
> > assigned device number 3
> > Jun 20 23:10:16 linux kernel: WARNING: USB Mass Storage data integrity
> > not assured
> > Jun 20 23:10:16 linux kernel: USB Mass Storage device found at 3
> > Jun 20 23:10:17 linux modprobe: modprobe: Can't locate module
> > block-major-11 Jun 20 23:10:17 linux last message repeated 15 times
> > Jun 20 23:10:18 linux /etc/hotplug/usb.agent[1565]: Can't ignore signal
> > CHLD, forcing to default.
> >
> > hwinfo --usb :
> > 04: USB 106.0: 10600 Disk
> > [Created at usb.100]
> > Unique ID: B3Fu.o9+kZpz6ig0
> > Hardware Class: disk
> > Model: "USB Storage Device"
> > Vendor: u0aec "?"
> > Device: 5010 "?"
> > SubVendor: ""
> > SubDevice: "USB Storage Device"
> > Revision: "1.00"
> > Serial ID: "0AEC301000001A00"
> > USB GUID: 0aec50100aec301000001a00
> > USB Device status: driver active ("usb-storage")
> > Speed: 1.5 Mbps
> > Attached to: #3 (Hub)
> >
> >
> >
> >
> > -------------------------------------------------------
> > Sponsored by:
> > ThinkGeek at http://www.ThinkGeek.com/
> > _______________________________________________
> > [EMAIL PROTECTED]
> > To unsubscribe, use the last form field at:
> > https://lists.sourceforge.net/lists/listinfo/linux-usb-users
-------------------------------------------------------
Sponsored by:
ThinkGeek at http://www.ThinkGeek.com/
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
