Hi all,
(I am new to USB on LInux)
I have been trying to set up a new (once used on W2K, but
deleted partitions) disk in Red Hat 7.3. Once the device
is plugged, proper entries appear in /proc/scasi :
$ pwd
/proc/scsi
$ ls
ide-scsi iscsi scsi usb-storage-0
$ cat usb-storage-0/2
Host scsi2: usb-storage
Vendor: MELCO INC.
Product: USB/IEEE1394-IDE Bridge
Serial Number: 0208068A3C
Protocol: 8020i
Transport: Bulk
GUID: 0411001d0000000208068a3c
Attached: 1
and in /proc/bus/usb :
$ cd /proc/bus/usb
$ ls
001 002 devices drivers
Obviously, now I have to partition the disk, format
partitions and mount them.
When I try :
/sbin/fdisk /dev/sdc
The command does not return the prompt, no error messages,
but the system hangs!
I can not do anything other than a cold boot! Even the
keyboard locks.
I would appreciate any help to resolve this problem.
Assela
PS: the dmesg:
Linux version 2.4.7-10enterprise
([EMAIL PROTECTED]) (gcc version 2.96
20000731 (Red Hat Linux 7.1 2.96-98)) #1 SMP Thu Sep 6
16:48:20 EDT 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff77000 (usable)
BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS)
BIOS-e820: 000000001ff79000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Scanning bios EBDA for MXT signature
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 130935
zone(0): 4096 pages.
zone(1): 126839 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: Dim 4300 APIC at:
0xFEE00000
Processor #0 Unknown CPU [15:1] APIC version 20
I/O APIC #1 Version 32 at 0xFEC00000.
Processors: 1
Kernel command line: ro root=/dev/hda7 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1695.028 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3381.65 BogoMIPS
Memory: 509712k/523740k available (1401k kernel code,
11580k reserved, 102k data, 240k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288
bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144
bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536
bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072
bytes)
Page-cache hash table entries: 131072 (order: 8, 1048576
bytes)
CPU: Before vendor init, caps: 3febfbff 00000000 00000000,
vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 3febfbff 00000000 00000000
00000000
CPU: After generic, caps: 3febfbff 00000000 00000000
00000000
CPU: Common caps: 3febfbff 00000000 00000000
00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch
([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 3febfbff 00000000 00000000,
vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 3febfbff 00000000 00000000
00000000
CPU: After generic, caps: 3febfbff 00000000 00000000
00000000
CPU: Common caps: 3febfbff 00000000 00000000
00000000
CPU0: Intel(R) Pentium(R) 4 CPU 1.70GHz stepping 02
per-CPU timeslice cutoff: 731.30 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-13, 1-20, 1-21, 1-22 not
connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 39.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
.... register #01: 00178020
....... : max redirection entries: 0017
....... : IO APIC version: 0020
WARNING: unexpected IO-APIC, please mail
to [EMAIL PROTECTED]
WARNING: unexpected IO-APIC, please mail
to [EMAIL PROTECTED]
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 000 00 1 0 0 0 0 0 0 00
0e 001 01 0 0 0 0 0 1 1 91
0f 001 01 0 0 0 0 0 1 1 99
10 001 01 1 1 0 1 0 1 1 A1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 B1
13 001 01 1 1 0 1 0 1 1 B9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1695.0701 MHz.
..... host bus clock speed is 99.7099 MHz.
cpu: 0, clocks: 997099, slice: 498549
CPU0<T0:997088,T1:498528,D:11,S:498549,C:997099>
PCI: PCI BIOS revision 2.10 entry at 0xfbece, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
PCI->APIC IRQ transform: (B0,I31,P3) -> 19
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P2) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I7,P0) -> 16
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Simple Boot Flag extension found and enabled.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
mxt_scan_bios: enter
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS
MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10d
block: queued sectors max/low 338437kB/207365kB, 1024
slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size
1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override
with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev f9
PIIX4: chipset revision 18
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA,
hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA,
hdd:pio
hda: ST380021A, ATA DISK drive
hdc: _NEC CD-RW NR-7900A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 156301488 sectors (80026 MB) w/2048KiB Cache,
CHS=9729/255/63, UDMA(100)
ide-floppy driver 0.97
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10
>
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ide-floppy driver 0.97
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 323k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,7): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 144995
ext3_orphan_cleanup: deleting unreferenced inode 208419
EXT3-fs: ide0(3,7): 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 240k freed
Adding Swap: 522072k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 17:01:38 Sep 6 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1f.2 to 64
usb-uhci.c: USB UHCI at I/O 0xff80, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1f.4 to 64
usb-uhci.c: USB UHCI at I/O 0xff60, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.251:USB Universal Host Controller Interface
driver
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,7), internal
journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,5), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,6), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,3), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,10), internal
journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: _NEC Model: NR-7900A Rev: 1.08
Type: CD-ROM ANSI SCSI
revision: 02
0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
0x378: PWord is 8 bits
0x378: Interrupts are ISA-Pulses
0x378: ECP port cfgA=0x10 cfgB=0x08
0x378: ECP settings irq=7 dma=<none or set by other means>
parport0: PC-style at 0x378 (0x778)
[PCSPP,TRISTATE,COMPAT,ECP]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
NET4: AppleTalk 0.18a for Linux NET4.0
8139too Fast Ethernet driver 0.9.18a
eth0: RealTek RTL8139 Fast Ethernet at 0xe08c8c00,
00:c0:a8:7b:b3:39, IRQ 16
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated
partner ability 45e1.
iSCSI version 2.0.1.8 ( 8-Aug-2001)
iSCSI control device major number 254
iSCSI: detected HBA d84f0d1c, host #1
scsi1 : iSCSI (2.0.1.8)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Unsupported Intel chipset (device id: 1a30), you
might want to try agp_try_unsupported=1.
agpgart: no supported devices found.
[drm] Initialized r128 2.1.6 20010405 on minor 0
Intel 810 + AC97 Audio, version 0.05, 17:01:23 Sep 6 2001
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH2 found at IO 0xcc40 and 0xc800, IRQ 17
ac97_codec: AC97 Audio codec, id: 0x4144:0x5360 (Analog
Devices AD1885)
i810_audio: setting clocking to 41260
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda
tray
Uniform CD-ROM driver Revision: 3.12
ISO 9660 Extensions: RRIP_1991A
hub.c: USB new device connect on bus1/1, assigned device
number 2
usb.c: USB device 2 (vend/prod 0x411/0x1d) is not claimed
by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-uhci.c: interrupt, status 2, frame# 1534
usb-uhci.c: interrupt, status 3, frame# 1535
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: SAMSUNG Model: SV8004H Rev:
Type: Direct-Access ANSI SCSI
revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Assela Pathirana, Hydraulics lab,
Science and Engineering Department of Chuo University
1-13-27, Kasuga, Bunkyo-ku, Tokyo 112-8551
Tel: +81 (3) 3817-1805/1807/Fax: 1803
__________________________________________________
Do You Yahoo!?
Yahoo! BB is Broadband by Yahoo!
http://bb.yahoo.co.jp/
-------------------------------------------------------
This sf.net email is sponsored by: OSDN - Tired of that same old
cell phone? Get a new here for FREE!
https://www.inphonic.com/r.asp?r=sourceforge1&refcode1=vs3390
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
