Hi,
OK, I've recompiled with verbose debugging enabled, rebooted the system,
plugged in the drive and attempted to mount the disk that's in it. The
following is the entire output of dmesg following the (failed) mount
attempt. I decided not to second guess what it is that you need from
this, so I've just included the whole thing. (/var/log/messages has the
same stuff as before in it)
-Kipp
--- begin dmesg.log ---
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 140k freed
Adding 2096472k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:01:05.0 [107b:1450]
Yenta: ISA IRQ mask 0x0898, PCI irq 10
Socket status: 30000007
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
inserting floppy driver for 2.6.3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: Maximum main memory to use for agp memory: 202M
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
[drm] Initialized i830 1.3.2 20021108 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
input: PS/2 Generic Mouse on isa0060/serio1
input: PC Speaker
PCI: Setting latency timer of device 0000:01:03.0 to 64
Intel(R) PRO/100 Network Driver - version 2.3.36-k1
Copyright (c) 2003 Intel Corporation
PCI: Setting latency timer of device 0000:01:08.0 to 64
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 10, io base 00001840
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:1d.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.3 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 10, io base 00001860
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:1d.1: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: ganged power switching
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
hub 1-0:1.0: port 2, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x301
usb 1-2: new low speed USB device using address 2
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 1-2: Product: USB-PS/2 Optical Mouse
usb 1-2: Manufacturer: Logitech
drivers/usb/core/usb.c: usb_hotplug
usb 1-2: registering 1-2:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
drivers/usb/host/uhci-hcd.c: 1860: suspend_hc
e100: eth0 NIC Link is Up 10 Mbps Half duplex
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x80f
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f7fe0(lo)
IPv6 over IPv4 tunneling driver
drivers/usb/core/usb.c: registered new driver hiddev
hid 1-2:1.0: usb_probe_interface
hid 1-2:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
eth0: no IPv6 routers present
hub 1-0:1.0: port 1, status 101, change 1, 12 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
usb 1-1: new full speed USB device using address 3
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
drivers/usb/core/message.c: USB device number 3 default language ID 0x409
usb 1-1: Product: eUSB ATA / ATAPI Adapter
usb 1-1: Manufacturer: SCM Microsystems Inc.
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: act_altsetting is 0, id_index is 27
usb-storage: -- associate_dev
usb-storage: Vendor: Shuttle
usb-storage: Product: CD-RW Device
usb-storage: Transport: Control/Bulk
usb-storage: Protocol: 8020i
usb-storage: Endpoints: In: 0xc9d2e8f4 Out: 0xc9d2e8e0 Int: 0xc9d2e908 (Period 32)
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code -32; transferred 0/36
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code -32; transferred 0/18
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Model: Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code -32; transferred 0/18
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- CB transport device requiring auto-sense
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code -32; transferred 0/18
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda : sector size 0 reported, assuming 512.
SCSI device sda: 1 512-byte hdwr sectors (0 MB)
sda: assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 01 00
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries
usb-storage: Status code -32; transferred 0/512
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- CB transport device requiring auto-sense
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
usb-storage: Status code 0; transferred 12/12
usb-storage: -- transfer complete
usb-storage: Call to usb_stor_ctrl_transfer() returned 0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code -32; transferred 0/18
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: CB data stage result is 0x2
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
attempt to access beyond end of device
sda: rw=0, want=66, limit=1
isofs_fill_super: bread failed, dev=sda, iso_blknum=16, block=32
--- end dmesg.log ---
On Tue, 2 Mar 2004, Matthew Dharm wrote:
> The device is reporting Direct-Access type, when it should be reporting
> CD-ROM type.
>
> Looking at the logs you provided, actually, it looks like it barely can
> answer an INQUIRY at all.
>
> To get something like this working, you'd have to rewrite the INQUIRY
> response data to set the type to CD-ROM. Before we go down that path,
> rebuild the driver with USB Mass Storage Verbose Debug turned on so we can
> see if something is going wrong with the INQUIRY or (more likely) the
> device is just busted.
>
> Matt
>
> On Tue, Mar 02, 2004 at 01:18:29AM -0500, Kipp Cannon wrote:
> > Hi,
> >
> > I've got an external cd-rom drive branded a "Microtech MicroCD" that I'm
> > having trouble getting to work with Linux 2.6.3 (the only version I've
> > tried it with). The drive attaches to a USB port on the host machine
> > through a cable that, at the drive end, has what looks like a "VHDCI"
> > high-density SCSI connector but is only about half the size.
> >
> > usbview reports the drive as a "eUSB ATA/ATAPI adapter" manufactured by
> > "SCM Microsystems Inc." (vendor/product/rev = 04e6/0101/2.00). Some
> > searching on Google revealed that SCM Microsystems manufactured a
> > USB-ATAPI bridge cable that has been used to attach various ATAPI drives
> > to USB ports, in particular the HP 8200e/8210e CD-Writer Plus.
> >
> > I suppose that's what I've got: a parallel-port ATAPI drive that's been
> > retrofitted to work with USB ports.
> >
> > Anyway...
> >
> > When I plug in the drive, the usb subsystem loads a bunch of stuff and
> > sets the drive up on /dev/sda with the following being put in
> > /var/log/messages
> >
> > --- begin /var/log/messages ---
> > Feb 26 19:44:45 localhost kernel: usb 1-1: new full speed USB device using address
> > 3
> > Feb 26 19:44:45 localhost kernel: SCSI subsystem initialized
> > Feb 26 19:44:45 localhost kernel: Initializing USB Mass Storage driver...
> > Feb 26 19:44:45 localhost kernel: scsi0 : SCSI emulation for USB Mass Storage
> > devices
> > Feb 26 19:44:45 localhost kernel: Vendor: Model: Rev:
> > Feb 26 19:44:45 localhost kernel: Type: Direct-Access
> > ANSI SCSI revision: 02
> > Feb 26 19:44:45 localhost kernel: drivers/usb/core/usb.c: registered new driver
> > usb-storage
> > Feb 26 19:44:45 localhost kernel: USB Mass Storage support registered.
> > Feb 26 19:44:45 localhost scsi.agent[4486]: disk at
> > /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/host0/0:0:0:0
> > Feb 26 19:44:45 localhost kernel: sda : sector size 0 reported, assuming 512.
> > Feb 26 19:44:45 localhost kernel: SCSI device sda: 1 512-byte hdwr sectors (0 MB)
> > Feb 26 19:44:45 localhost kernel: sda:<7>usb-storage: queuecommand called
> > Feb 26 19:44:45 localhost kernel: unknown partition table
> > Feb 26 19:44:45 localhost kernel: Attached scsi disk sda at scsi0, channel 0, id
> > 0, lun 0
> > --- end /var/log/messages ---
> >
> > If I place a disk in the drive, when I try to mount it the attempt fails
> > with the following being placed in /var/log/messages:
> >
> > --- begin /var/log/messages ---
> > Feb 26 19:46:58 localhost kernel: attempt to access beyond end of device
> > Feb 26 19:46:58 localhost kernel: sda: rw=0, want=66, limit=1
> > Feb 26 19:46:58 localhost kernel: isofs_fill_super: bread failed, dev=sda,
> > iso_blknum=16, block=32
> > --- end /var/log/messages ---
> >
> > Does somewhat have some idea how to get this drive working? Thanks.
> >
> > -Kipp
> >
> >
> >
> > -------------------------------------------------------
> > SF.Net is sponsored by: Speed Start Your Linux Apps Now.
> > Build and deploy apps & Web services for Linux with
> > a free DVD software kit from IBM. Click Now!
> > http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click
> > _______________________________________________
> > [EMAIL PROTECTED]
> > To unsubscribe, use the last form field at:
> > https://lists.sourceforge.net/lists/listinfo/linux-usb-users
>
> --
> Matthew Dharm Home: [EMAIL PROTECTED]
> Maintainer, Linux USB Mass Storage Driver
>
> A: The most ironic oxymoron wins ...
> DP: "Microsoft Works"
> A: Uh, okay, you win.
> -- A.J. & Dust Puppy
> User Friendly, 1/18/1998
>
-------------------------------------------------------
SF.Net is sponsored by: Speed Start Your Linux Apps Now.
Build and deploy apps & Web services for Linux with
a free DVD software kit from IBM. Click Now!
http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
