On Mon, Nov 14, 2016 at 08:24:45AM -0500, Jes Sorensen wrote:
> Barry Day <brise...@gmail.com> writes:
> > The rtl8192e and rtl8723 fail to reconnect to an AP after being
> > disconnected. Ths patch fixes that without affecting the rtl8192cu.
> > I don't have a rtl8723 to test but it has been tested on a rtl8192eu.
> > After going through the orginal realtek code for the rtl8723, I am
> > confident the patch is applicable to both.
> >
> > Signed-off-by: Barry Day <brise...@gmail.com>
> > ---
> > rtl8xxxu_core.c | 18 ++++++++++++++----
> > 1 file changed, 14 insertions(+), 4 deletions(-)
>
> Hi Barry,
>
> Thank you for the patch. There are a couple of items which I am not
> 100% sure about the order of.
>
> > diff --git a/rtl8xxxu_core.c b/rtl8xxxu_core.c
> > index 04141e5..6ac10d2 100644
> > --- a/rtl8xxxu_core.c
> > +++ b/rtl8xxxu_core.c
> > @@ -4372,17 +4372,25 @@ void rtl8xxxu_gen1_report_connect(struct
> > rtl8xxxu_priv *priv,
> > void rtl8xxxu_gen2_report_connect(struct rtl8xxxu_priv *priv,
> > u8 macid, bool connect)
> > {
> > + u8 val8;
> > struct h2c_cmd h2c;
> >
> > memset(&h2c, 0, sizeof(struct h2c_cmd));
> >
> > h2c.media_status_rpt.cmd = H2C_8723B_MEDIA_STATUS_RPT;
> > - if (connect)
> > + if (connect) {
> > h2c.media_status_rpt.parm |= BIT(0);
> > - else
> > - h2c.media_status_rpt.parm &= ~BIT(0);
> > + rtl8xxxu_gen2_h2c_cmd(priv, &h2c,
> > + sizeof(h2c.media_status_rpt));
> > + } else {
> > + val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL);
> > + val8 &= ~BEACON_FUNCTION_ENABLE;
> > +
> > + rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8);
> > + rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0x00);
> > + rtl8xxxu_write8(priv, REG_DUAL_TSF_RST, (BIT(0) | BIT(1)));
> > + }
> >
> > - rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.media_status_rpt));
> > }
>
> This only affects 8192eu and not 8192cu - we left RXFLTMAP2 out of here
> on purpose for monitor mode, but you now disable it for 8192eu/8723bu.
>
Even in monitor mode the interface has to brought up to use it which invokes
rtl8xxxu_start which sets it back to accepting frames.
> > void rtl8xxxu_gen1_init_aggregation(struct rtl8xxxu_priv *priv)
> > @@ -4515,6 +4523,8 @@ rtl8xxxu_bss_info_changed(struct ieee80211_hw *hw,
> > struct ieee80211_vif *vif,
> > sgi = 1;
> > rcu_read_unlock();
> >
> > + rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0xffff);
> > +
> > priv->fops->update_rate_mask(priv, ramask, sgi);
> >
> > rtl8xxxu_write8(priv, REG_BCN_MAX_ERR, 0xff);
>
> Here you enable RXFLTMAP2 for all devices - this doesn't balance with
> the above.
>
The original realtek code I have for the 8192cu does the disconnect the
same way as in this patch. I tested the 8192cu using the patched
gen2_report connect and it works. That would make things consistent across
all chipsets.
