Barry Day <brise...@gmail.com> writes:
> On Mon, Nov 14, 2016 at 08:24:45AM -0500, Jes Sorensen wrote:
>> Barry Day <brise...@gmail.com> writes:
>> > The rtl8192e and rtl8723 fail to reconnect to an AP after being
>> > disconnected. Ths patch fixes that without affecting the rtl8192cu.
>> > I don't have a rtl8723 to test but it has been tested on a rtl8192eu.
>> > After going through the orginal realtek code for the rtl8723, I am
>> > confident the patch is applicable to both.
>> >
>> > Signed-off-by: Barry Day <brise...@gmail.com>
>> > ---
>> > rtl8xxxu_core.c | 18 ++++++++++++++----
>> > 1 file changed, 14 insertions(+), 4 deletions(-)
>>
>> Hi Barry,
>>
>> Thank you for the patch. There are a couple of items which I am not
>> 100% sure about the order of.
>>
>> > diff --git a/rtl8xxxu_core.c b/rtl8xxxu_core.c
>> > index 04141e5..6ac10d2 100644
>> > --- a/rtl8xxxu_core.c
>> > +++ b/rtl8xxxu_core.c
>> > @@ -4372,17 +4372,25 @@ void rtl8xxxu_gen1_report_connect(struct
>> > rtl8xxxu_priv *priv,
>> > void rtl8xxxu_gen2_report_connect(struct rtl8xxxu_priv *priv,
>> > u8 macid, bool connect)
>> > {
>> > + u8 val8;
>> > struct h2c_cmd h2c;
>> >
>> > memset(&h2c, 0, sizeof(struct h2c_cmd));
>> >
>> > h2c.media_status_rpt.cmd = H2C_8723B_MEDIA_STATUS_RPT;
>> > - if (connect)
>> > + if (connect) {
>> > h2c.media_status_rpt.parm |= BIT(0);
>> > - else
>> > - h2c.media_status_rpt.parm &= ~BIT(0);
>> > + rtl8xxxu_gen2_h2c_cmd(priv, &h2c,
>> > + sizeof(h2c.media_status_rpt));
>> > + } else {
>> > + val8 = rtl8xxxu_read8(priv, REG_BEACON_CTRL);
>> > + val8 &= ~BEACON_FUNCTION_ENABLE;
>> > +
>> > + rtl8xxxu_write8(priv, REG_BEACON_CTRL, val8);
>> > + rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0x00);
>> > + rtl8xxxu_write8(priv, REG_DUAL_TSF_RST, (BIT(0) | BIT(1)));
>> > + }
>> >
>> > - rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.media_status_rpt));
>> > }
>>
>> This only affects 8192eu and not 8192cu - we left RXFLTMAP2 out of here
>> on purpose for monitor mode, but you now disable it for 8192eu/8723bu.
>
> Even in monitor mode the interface has to brought up to use it which invokes
> rtl8xxxu_start which sets it back to accepting frames.
>
>
>> > void rtl8xxxu_gen1_init_aggregation(struct rtl8xxxu_priv *priv)
>> > @@ -4515,6 +4523,8 @@ rtl8xxxu_bss_info_changed(struct ieee80211_hw *hw,
>> > struct ieee80211_vif *vif,
>> > sgi = 1;
>> > rcu_read_unlock();
>> >
>> > + rtl8xxxu_write16(priv, REG_RXFLTMAP2, 0xffff);
>> > +
>> > priv->fops->update_rate_mask(priv, ramask, sgi);
>> >
>> > rtl8xxxu_write8(priv, REG_BCN_MAX_ERR, 0xff);
>>
>> Here you enable RXFLTMAP2 for all devices - this doesn't balance with
>> the above.
>
> The original realtek code I have for the 8192cu does the disconnect the
> same way as in this patch. I tested the 8192cu using the patched
> gen2_report connect and it works. That would make things consistent across
> all chipsets.
My concern is that you only set FLATMAP and BEACON_CTRL for gen2
devices, which has zero impact on gen1 devices, such as the 8192cu. If
need to do this for gen2 (8723bu/8192eu) I assume we need to do it for
gen1 as well.
I'd like to see us do a little more investigating on this first.
Jes
