Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.

This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.

Signed-off-by: Phoebe Buckheister <phoebe.buckheis...@itwm.fraunhofer.de>
---
 drivers/net/ieee802154/at86rf230.c |   25 ++++++++++++++++++
 include/linux/nl802154.h           |    4 +++
 include/net/mac802154.h            |    5 ++++
 include/net/wpan-phy.h             |    6 +++--
 net/ieee802154/ieee802154.h        |    1 +
 net/ieee802154/netlink.c           |    1 +
 net/ieee802154/nl-phy.c            |   49 +++++++++++++++++++++++++++++++++++-
 net/ieee802154/nl_policy.c         |    2 ++
 net/ieee802154/wpan-class.c        |    4 +--
 net/mac802154/ieee802154_dev.c     |   11 ++++++++
 10 files changed, 102 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ieee802154/at86rf230.c 
b/drivers/net/ieee802154/at86rf230.c
index 19ed297..507e8fc 100644
--- a/drivers/net/ieee802154/at86rf230.c
+++ b/drivers/net/ieee802154/at86rf230.c
@@ -757,6 +757,30 @@ at86rf230_set_hw_addr_filt(struct ieee802154_dev *dev,
        return 0;
 }
 
+static int
+at86rf212_set_txpower(struct ieee802154_dev *dev, int db)
+{
+       struct at86rf230_local *lp = dev->priv;
+       int rc;
+
+       /* typical maximum output is 5dBm with RG_PHY_TX_PWR 0x60, lower five
+        * bits decrease power in 1dB steps. 0x60 represents extra PA gain of
+        * 0dB.
+        * thus, supported values for db range from -26 to 5, for 31dB of
+        * reduction to 0dB of reduction.
+        */
+       if (db > 5 || db < -26)
+               return -EINVAL;
+
+       db = -(db - 5);
+
+       rc = __at86rf230_write(lp, RG_PHY_TX_PWR, 0x60 | db);
+       if (rc)
+               return rc;
+
+       return 0;
+}
+
 static struct ieee802154_ops at86rf230_ops = {
        .owner = THIS_MODULE,
        .xmit = at86rf230_xmit,
@@ -775,6 +799,7 @@ static struct ieee802154_ops at86rf212_ops = {
        .start = at86rf230_start,
        .stop = at86rf230_stop,
        .set_hw_addr_filt = at86rf230_set_hw_addr_filt,
+       .set_txpower = at86rf212_set_txpower,
 };
 
 static void at86rf230_irqwork(struct work_struct *work)
diff --git a/include/linux/nl802154.h b/include/linux/nl802154.h
index fd4f2d1..625d19e 100644
--- a/include/linux/nl802154.h
+++ b/include/linux/nl802154.h
@@ -70,6 +70,8 @@ enum {
        IEEE802154_ATTR_PHY_NAME,
        IEEE802154_ATTR_DEV_TYPE,
 
+       IEEE802154_ATTR_TXPOWER,
+
        __IEEE802154_ATTR_MAX,
 };
 
@@ -122,6 +124,8 @@ enum {
        IEEE802154_ADD_IFACE,
        IEEE802154_DEL_IFACE,
 
+       IEEE802154_SET_PHYPARAMS,
+
        __IEEE802154_CMD_MAX,
 };
 
diff --git a/include/net/mac802154.h b/include/net/mac802154.h
index 807d6b7..8bd2785 100644
--- a/include/net/mac802154.h
+++ b/include/net/mac802154.h
@@ -113,6 +113,10 @@ struct ieee802154_dev {
  *       Set radio for listening on specific address.
  *       Set the device for listening on specified address.
  *       Returns either zero, or negative errno.
+ *
+ * set_txpower:
+ *       Set radio transmit power in dB. Called with pib_lock held.
+ *       Returns either zero, or negative errno.
  */
 struct ieee802154_ops {
        struct module   *owner;
@@ -129,6 +133,7 @@ struct ieee802154_ops {
                                            unsigned long changed);
        int             (*ieee_addr)(struct ieee802154_dev *dev,
                                     u8 addr[IEEE802154_ADDR_LEN]);
+       int             (*set_txpower)(struct ieee802154_dev *dev, int db);
 };
 
 /* Basic interface to register ieee802154 device */
diff --git a/include/net/wpan-phy.h b/include/net/wpan-phy.h
index b52bda8..47fc0c1 100644
--- a/include/net/wpan-phy.h
+++ b/include/net/wpan-phy.h
@@ -37,14 +37,14 @@ struct wpan_phy {
        struct mutex pib_lock;
 
        /*
-        * This is a PIB according to 802.15.4-2006.
+        * This is a PIB according to 802.15.4-2011.
         * We do not provide timing-related variables, as they
         * aren't used outside of driver
         */
        u8 current_channel;
        u8 current_page;
        u32 channels_supported[32];
-       u8 transmit_power;
+       s8 transmit_power;
        u8 cca_mode;
 
        struct device dev;
@@ -54,6 +54,8 @@ struct wpan_phy {
                                        const char *name, int type);
        void (*del_iface)(struct wpan_phy *phy, struct net_device *dev);
 
+       int (*set_txpower)(struct wpan_phy *phy, int db);
+
        char priv[0] __attribute__((__aligned__(NETDEV_ALIGN)));
 };
 
diff --git a/net/ieee802154/ieee802154.h b/net/ieee802154/ieee802154.h
index cee4425..6cbc896 100644
--- a/net/ieee802154/ieee802154.h
+++ b/net/ieee802154/ieee802154.h
@@ -53,6 +53,7 @@ int ieee802154_list_phy(struct sk_buff *skb, struct genl_info 
*info);
 int ieee802154_dump_phy(struct sk_buff *skb, struct netlink_callback *cb);
 int ieee802154_add_iface(struct sk_buff *skb, struct genl_info *info);
 int ieee802154_del_iface(struct sk_buff *skb, struct genl_info *info);
+int ieee802154_set_phyparams(struct sk_buff *skb, struct genl_info *info);
 
 enum ieee802154_mcgrp_ids {
        IEEE802154_COORD_MCGRP,
diff --git a/net/ieee802154/netlink.c b/net/ieee802154/netlink.c
index 43f1b2b..67c151b 100644
--- a/net/ieee802154/netlink.c
+++ b/net/ieee802154/netlink.c
@@ -115,6 +115,7 @@ static const struct genl_ops ieee8021154_ops[] = {
                        ieee802154_dump_phy),
        IEEE802154_OP(IEEE802154_ADD_IFACE, ieee802154_add_iface),
        IEEE802154_OP(IEEE802154_DEL_IFACE, ieee802154_del_iface),
+       IEEE802154_OP(IEEE802154_SET_PHYPARAMS, ieee802154_set_phyparams),
        /* see nl-mac.c */
        IEEE802154_OP(IEEE802154_ASSOCIATE_REQ, ieee802154_associate_req),
        IEEE802154_OP(IEEE802154_ASSOCIATE_RESP, ieee802154_associate_resp),
diff --git a/net/ieee802154/nl-phy.c b/net/ieee802154/nl-phy.c
index 89b265a..d3ee62f 100644
--- a/net/ieee802154/nl-phy.c
+++ b/net/ieee802154/nl-phy.c
@@ -55,7 +55,8 @@ static int ieee802154_nl_fill_phy(struct sk_buff *msg, u32 
portid,
        mutex_lock(&phy->pib_lock);
        if (nla_put_string(msg, IEEE802154_ATTR_PHY_NAME, wpan_phy_name(phy)) ||
            nla_put_u8(msg, IEEE802154_ATTR_PAGE, phy->current_page) ||
-           nla_put_u8(msg, IEEE802154_ATTR_CHANNEL, phy->current_channel))
+           nla_put_u8(msg, IEEE802154_ATTR_CHANNEL, phy->current_channel) ||
+           nla_put_s8(msg, IEEE802154_ATTR_TXPOWER, phy->transmit_power))
                goto nla_put_failure;
        for (i = 0; i < 32; i++) {
                if (phy->channels_supported[i])
@@ -354,3 +355,49 @@ out_dev:
 
        return rc;
 }
+
+int ieee802154_set_phyparams(struct sk_buff *skb, struct genl_info *info)
+{
+       struct wpan_phy *phy;
+       const char *name;
+       int txpower;
+       int rc = -EINVAL;
+
+       pr_debug("%s\n", __func__);
+
+       if (!info->attrs[IEEE802154_ATTR_PHY_NAME])
+               return -EINVAL;
+
+       name = nla_data(info->attrs[IEEE802154_ATTR_PHY_NAME]);
+       if (name[nla_len(info->attrs[IEEE802154_ATTR_PHY_NAME]) - 1] != '\0')
+               return -EINVAL; /* phy name should be null-terminated */
+
+       txpower = nla_get_s8(info->attrs[IEEE802154_ATTR_TXPOWER]);
+
+       phy = wpan_phy_find(name);
+       if (!phy)
+               return -ENODEV;
+
+       if (!phy->set_txpower)
+               goto out;
+
+       mutex_lock(&phy->pib_lock);
+
+       rc = phy->set_txpower(phy, txpower);
+       if (rc < 0) {
+               mutex_unlock(&phy->pib_lock);
+               goto out;
+       }
+
+       phy->transmit_power = txpower;
+
+       mutex_unlock(&phy->pib_lock);
+
+       wpan_phy_put(phy);
+
+       return 0;
+
+out:
+       wpan_phy_put(phy);
+       return rc;
+}
diff --git a/net/ieee802154/nl_policy.c b/net/ieee802154/nl_policy.c
index 6adda4d..90b1d0d 100644
--- a/net/ieee802154/nl_policy.c
+++ b/net/ieee802154/nl_policy.c
@@ -52,5 +52,7 @@ const struct nla_policy ieee802154_policy[IEEE802154_ATTR_MAX 
+ 1] = {
        [IEEE802154_ATTR_DURATION] = { .type = NLA_U8, },
        [IEEE802154_ATTR_ED_LIST] = { .len = 27 },
        [IEEE802154_ATTR_CHANNEL_PAGE_LIST] = { .len = 32 * 4, },
+
+       [IEEE802154_ATTR_TXPOWER] = { .type = NLA_S8, },
 };
 
diff --git a/net/ieee802154/wpan-class.c b/net/ieee802154/wpan-class.c
index ef56ab5..8d6f670 100644
--- a/net/ieee802154/wpan-class.c
+++ b/net/ieee802154/wpan-class.c
@@ -44,9 +44,7 @@ static DEVICE_ATTR_RO(name);
 
 MASTER_SHOW(current_channel, "%d");
 MASTER_SHOW(current_page, "%d");
-MASTER_SHOW_COMPLEX(transmit_power, "%d +- %d dB",
-       ((signed char) (phy->transmit_power << 2)) >> 2,
-       (phy->transmit_power >> 6) ? (phy->transmit_power >> 6) * 3 : 1 );
+MASTER_SHOW(transmit_power, "%d +- 1 dB");
 MASTER_SHOW(cca_mode, "%d");
 
 static ssize_t channels_supported_show(struct device *dev,
diff --git a/net/mac802154/ieee802154_dev.c b/net/mac802154/ieee802154_dev.c
index 52ae664..9eb49e0 100644
--- a/net/mac802154/ieee802154_dev.c
+++ b/net/mac802154/ieee802154_dev.c
@@ -165,6 +165,16 @@ err:
        return ERR_PTR(err);
 }
 
+static int mac802154_set_txpower(struct wpan_phy *phy, int db)
+{
+       struct mac802154_priv *priv = wpan_phy_priv(phy);
+
+       if (!priv->ops->set_txpower)
+               return -ENOTSUPP;
+
+       return priv->ops->set_txpower(&priv->hw, db);
+}
+
 struct ieee802154_dev *
 ieee802154_alloc_device(size_t priv_data_len, struct ieee802154_ops *ops)
 {
@@ -242,6 +252,7 @@ int ieee802154_register_device(struct ieee802154_dev *dev)
 
        priv->phy->add_iface = mac802154_add_iface;
        priv->phy->del_iface = mac802154_del_iface;
+       priv->phy->set_txpower = mac802154_set_txpower;
 
        rc = wpan_phy_register(priv->phy);
        if (rc < 0)
-- 
1.7.9.5


------------------------------------------------------------------------------
Managing the Performance of Cloud-Based Applications
Take advantage of what the Cloud has to offer - Avoid Common Pitfalls.
Read the Whitepaper.
http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk
_______________________________________________
Linux-zigbee-devel mailing list
Linux-zigbee-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-zigbee-devel

Reply via email to