Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:
* force the initial state after P_ON to FORCE_TRX_OFF to work around a
documented erratum
* channels_supported depends on the frequency of the transceiver, and
thus is_rf212
* do early detection of chip version select an appropriate _ops struct
based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheis...@itwm.fraunhofer.de>
---
drivers/net/ieee802154/at86rf230.c | 270 ++++++++++++++++++++++++------------
1 file changed, 181 insertions(+), 89 deletions(-)
diff --git a/drivers/net/ieee802154/at86rf230.c
b/drivers/net/ieee802154/at86rf230.c
index 2cbe1c2..19ed297 100644
--- a/drivers/net/ieee802154/at86rf230.c
+++ b/drivers/net/ieee802154/at86rf230.c
@@ -37,7 +37,6 @@
struct at86rf230_local {
struct spi_device *spi;
- int rstn, slp_tr, dig2;
u8 part;
u8 vers;
@@ -55,6 +54,11 @@ struct at86rf230_local {
bool is_tx;
};
+static inline int is_rf212(struct at86rf230_local *local)
+{
+ return local->part == 7;
+}
+
#define RG_TRX_STATUS (0x01)
#define SR_TRX_STATUS 0x01, 0x1f, 0
#define SR_RESERVED_01_3 0x01, 0x20, 5
@@ -100,7 +104,9 @@ struct at86rf230_local {
#define SR_SFD_VALUE 0x0b, 0xff, 0
#define RG_TRX_CTRL_2 (0x0c)
#define SR_OQPSK_DATA_RATE 0x0c, 0x03, 0
-#define SR_RESERVED_0c_2 0x0c, 0x7c, 2
+#define SR_SUB_MODE 0x0c, 0x04, 2
+#define SR_BPSK_QPSK 0x0c, 0x08, 3
+#define SR_RESERVED_0c_4 0x0c, 0x70, 4
#define SR_RX_SAFE_MODE 0x0c, 0x80, 7
#define RG_ANT_DIV (0x0d)
#define SR_ANT_CTRL 0x0d, 0x03, 0
@@ -244,6 +250,57 @@ struct at86rf230_local {
#define STATE_TRANSITION_IN_PROGRESS 0x1F
static int
+__at86rf230_detect_device(struct spi_device *spi, u16 *man_id, u8 *part,
+ u8 *version)
+{
+ u8 data[4];
+ u8 *buf = kmalloc(2, GFP_KERNEL);
+ int status;
+ struct spi_message msg;
+ struct spi_transfer xfer = {
+ .len = 2,
+ .tx_buf = buf,
+ .rx_buf = buf,
+ };
+ u8 reg;
+
+ if (!buf)
+ return -ENOMEM;
+
+ for (reg = RG_PART_NUM; reg <= RG_MAN_ID_1; reg++) {
+ buf[0] = (reg & CMD_REG_MASK) | CMD_REG;
+ buf[1] = 0xff;
+ dev_vdbg(&spi->dev, "buf[0] = %02x\n", buf[0]);
+ spi_message_init(&msg);
+ spi_message_add_tail(&xfer, &msg);
+
+ status = spi_sync(spi, &msg);
+ dev_vdbg(&spi->dev, "status = %d\n", status);
+ if (msg.status)
+ status = msg.status;
+
+ dev_vdbg(&spi->dev, "status = %d\n", status);
+ dev_vdbg(&spi->dev, "buf[0] = %02x\n", buf[0]);
+ dev_vdbg(&spi->dev, "buf[1] = %02x\n", buf[1]);
+
+ if (status == 0)
+ data[reg - RG_PART_NUM] = buf[1];
+ else
+ break;
+ }
+
+ if (status == 0) {
+ *part = data[0];
+ *version = data[1];
+ *man_id = (data[3] << 8) | data[2];
+ }
+
+ kfree(buf);
+
+ return status;
+}
+
+static int
__at86rf230_write(struct at86rf230_local *lp, u8 addr, u8 data)
{
u8 *buf = lp->buf;
@@ -520,6 +577,29 @@ at86rf230_stop(struct ieee802154_dev *dev)
}
static int
+at86rf230_set_channel(struct at86rf230_local *lp, int page, int channel)
+{
+ return at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+}
+
+static int
+at86rf212_set_channel(struct at86rf230_local *lp, int page, int channel)
+{
+ int rc;
+
+ if (channel == 0) {
+ rc = at86rf230_write_subreg(lp, SR_SUB_MODE, 0);
+ } else {
+ rc = at86rf230_write_subreg(lp, SR_SUB_MODE, 1);
+ }
+
+ if (rc < 0)
+ return rc;
+
+ return at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+}
+
+static int
at86rf230_channel(struct ieee802154_dev *dev, int page, int channel)
{
struct at86rf230_local *lp = dev->priv;
@@ -527,12 +607,21 @@ at86rf230_channel(struct ieee802154_dev *dev, int page,
int channel)
might_sleep();
- if (page != 0 || channel < 11 || channel > 26) {
+ if (page < 0
+ || page > 31
+ || !(lp->dev->phy->channels_supported[page] & BIT(channel))) {
WARN_ON(1);
return -EINVAL;
}
- rc = at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+ if (is_rf212(lp))
+ rc = at86rf212_set_channel(lp, page, channel);
+ else
+ rc = at86rf230_set_channel(lp, page, channel);
+
+ if (rc < 0)
+ return rc;
+
msleep(1); /* Wait for PLL */
dev->phy->current_channel = channel;
@@ -678,6 +767,16 @@ static struct ieee802154_ops at86rf230_ops = {
.set_hw_addr_filt = at86rf230_set_hw_addr_filt,
};
+static struct ieee802154_ops at86rf212_ops = {
+ .owner = THIS_MODULE,
+ .xmit = at86rf230_xmit,
+ .ed = at86rf230_ed,
+ .set_channel = at86rf230_channel,
+ .start = at86rf230_start,
+ .stop = at86rf230_stop,
+ .set_hw_addr_filt = at86rf230_set_hw_addr_filt,
+};
+
static void at86rf230_irqwork(struct work_struct *work)
{
struct at86rf230_local *lp =
@@ -759,7 +858,7 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
dev_info(&lp->spi->dev, "Status: %02x\n", status);
if (status == STATE_P_ON) {
- rc = at86rf230_write_subreg(lp, SR_TRX_CMD, STATE_TRX_OFF);
+ rc = at86rf230_write_subreg(lp, SR_TRX_CMD,
STATE_FORCE_TRX_OFF);
if (rc)
return rc;
msleep(1);
@@ -824,26 +923,18 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
return 0;
}
-static void at86rf230_fill_data(struct spi_device *spi)
-{
- struct at86rf230_local *lp = spi_get_drvdata(spi);
- struct at86rf230_platform_data *pdata = spi->dev.platform_data;
-
- lp->rstn = pdata->rstn;
- lp->slp_tr = pdata->slp_tr;
- lp->dig2 = pdata->dig2;
-}
-
static int at86rf230_probe(struct spi_device *spi)
{
struct at86rf230_platform_data *pdata;
struct ieee802154_dev *dev;
struct at86rf230_local *lp;
- u8 man_id_0, man_id_1, status;
+ u16 man_id = 0;
+ u8 part = 0, version = 0, status;
irq_handler_t irq_handler;
work_func_t irq_worker;
- int rc, supported = 0;
+ int rc;
const char *chip;
+ struct ieee802154_ops *ops = NULL;
if (!spi->irq) {
dev_err(&spi->dev, "no IRQ specified\n");
@@ -856,116 +947,115 @@ static int at86rf230_probe(struct spi_device *spi)
return -EINVAL;
}
- dev = ieee802154_alloc_device(sizeof(*lp), &at86rf230_ops);
- if (!dev)
- return -ENOMEM;
-
- lp = dev->priv;
- lp->dev = dev;
-
- lp->spi = spi;
-
- dev->parent = &spi->dev;
- dev->extra_tx_headroom = 0;
- /* We do support only 2.4 Ghz */
- dev->phy->channels_supported[0] = 0x7FFF800;
- dev->flags = IEEE802154_HW_OMIT_CKSUM;
-
- if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
- irq_worker = at86rf230_irqwork;
- irq_handler = at86rf230_isr;
- } else {
- irq_worker = at86rf230_irqwork_level;
- irq_handler = at86rf230_isr_level;
- }
-
- mutex_init(&lp->bmux);
- INIT_WORK(&lp->irqwork, irq_worker);
- spin_lock_init(&lp->lock);
- init_completion(&lp->tx_complete);
-
- spi_set_drvdata(spi, lp);
-
- at86rf230_fill_data(spi);
-
- rc = gpio_request(lp->rstn, "rstn");
+ rc = gpio_request(pdata->rstn, "rstn");
if (rc)
- goto err_rstn;
+ return rc;
- if (gpio_is_valid(lp->slp_tr)) {
- rc = gpio_request(lp->slp_tr, "slp_tr");
+ if (gpio_is_valid(pdata->slp_tr)) {
+ rc = gpio_request(pdata->slp_tr, "slp_tr");
if (rc)
goto err_slp_tr;
}
- rc = gpio_direction_output(lp->rstn, 1);
+ rc = gpio_direction_output(pdata->rstn, 1);
if (rc)
goto err_gpio_dir;
- if (gpio_is_valid(lp->slp_tr)) {
- rc = gpio_direction_output(lp->slp_tr, 0);
+ if (gpio_is_valid(pdata->slp_tr)) {
+ rc = gpio_direction_output(pdata->slp_tr, 0);
if (rc)
goto err_gpio_dir;
}
/* Reset */
msleep(1);
- gpio_set_value(lp->rstn, 0);
+ gpio_set_value(pdata->rstn, 0);
msleep(1);
- gpio_set_value(lp->rstn, 1);
+ gpio_set_value(pdata->rstn, 1);
msleep(1);
- rc = at86rf230_read_subreg(lp, SR_MAN_ID_0, &man_id_0);
- if (rc)
- goto err_gpio_dir;
- rc = at86rf230_read_subreg(lp, SR_MAN_ID_1, &man_id_1);
- if (rc)
+ rc = __at86rf230_detect_device(spi, &man_id, &part, &version);
+ if (rc < 0)
goto err_gpio_dir;
- if (man_id_1 != 0x00 || man_id_0 != 0x1f) {
+ if (man_id != 0x001f) {
dev_err(&spi->dev, "Non-Atmel dev found (MAN_ID %02x %02x)\n",
- man_id_1, man_id_0);
+ man_id >> 8, man_id & 0xFF);
rc = -EINVAL;
goto err_gpio_dir;
}
- rc = at86rf230_read_subreg(lp, SR_PART_NUM, &lp->part);
- if (rc)
- goto err_gpio_dir;
-
- rc = at86rf230_read_subreg(lp, SR_VERSION_NUM, &lp->vers);
- if (rc)
- goto err_gpio_dir;
-
- switch (lp->part) {
+ switch (part) {
case 2:
chip = "at86rf230";
- /* supported = 1; FIXME: should be easy to support; */
+ /* FIXME: should be easy to support; */
break;
case 3:
chip = "at86rf231";
- supported = 1;
+ ops = &at86rf230_ops;
+ break;
+ case 7:
+ chip = "at86rf212";
+ if (version == 1)
+ ops = &at86rf212_ops;
break;
default:
chip = "UNKNOWN";
break;
}
- dev_info(&spi->dev, "Detected %s chip version %d\n", chip, lp->vers);
- if (!supported) {
+ dev_info(&spi->dev, "Detected %s chip version %d\n", chip, version);
+ if (!ops) {
rc = -ENOTSUPP;
goto err_gpio_dir;
}
+ dev = ieee802154_alloc_device(sizeof(*lp), ops);
+ if (!dev) {
+ rc = -ENOMEM;
+ goto err_gpio_dir;
+ }
+
+ lp = dev->priv;
+ lp->dev = dev;
+ lp->part = part;
+ lp->vers = version;
+
+ lp->spi = spi;
+
+ dev->parent = &spi->dev;
+ dev->extra_tx_headroom = 0;
+ dev->flags = IEEE802154_HW_OMIT_CKSUM;
+
+ if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+ irq_worker = at86rf230_irqwork;
+ irq_handler = at86rf230_isr;
+ } else {
+ irq_worker = at86rf230_irqwork_level;
+ irq_handler = at86rf230_isr_level;
+ }
+
+ mutex_init(&lp->bmux);
+ INIT_WORK(&lp->irqwork, irq_worker);
+ spin_lock_init(&lp->lock);
+ init_completion(&lp->tx_complete);
+
+ spi_set_drvdata(spi, lp);
+
+ if (is_rf212(lp))
+ dev->phy->channels_supported[0] = 0x00007FF;
+ else
+ dev->phy->channels_supported[0] = 0x7FFF800;
+
rc = at86rf230_hw_init(lp);
if (rc)
- goto err_gpio_dir;
+ goto err_hw_init;
rc = request_irq(spi->irq, irq_handler,
IRQF_SHARED | pdata->irq_type,
dev_name(&spi->dev), lp);
if (rc)
- goto err_gpio_dir;
+ goto err_hw_init;
/* Read irq status register to reset irq line */
rc = at86rf230_read_subreg(lp, RG_IRQ_STATUS, 0xff, 0, &status);
@@ -980,31 +1070,33 @@ static int at86rf230_probe(struct spi_device *spi)
err_irq:
free_irq(spi->irq, lp);
+err_hw_init:
flush_work(&lp->irqwork);
-err_gpio_dir:
- if (gpio_is_valid(lp->slp_tr))
- gpio_free(lp->slp_tr);
-err_slp_tr:
- gpio_free(lp->rstn);
-err_rstn:
spi_set_drvdata(spi, NULL);
mutex_destroy(&lp->bmux);
ieee802154_free_device(lp->dev);
+
+err_gpio_dir:
+ if (gpio_is_valid(pdata->slp_tr))
+ gpio_free(pdata->slp_tr);
+err_slp_tr:
+ gpio_free(pdata->rstn);
return rc;
}
static int at86rf230_remove(struct spi_device *spi)
{
struct at86rf230_local *lp = spi_get_drvdata(spi);
+ struct at86rf230_platform_data *pdata = spi->dev.platform_data;
ieee802154_unregister_device(lp->dev);
free_irq(spi->irq, lp);
flush_work(&lp->irqwork);
- if (gpio_is_valid(lp->slp_tr))
- gpio_free(lp->slp_tr);
- gpio_free(lp->rstn);
+ if (gpio_is_valid(pdata->slp_tr))
+ gpio_free(pdata->slp_tr);
+ gpio_free(pdata->rstn);
spi_set_drvdata(spi, NULL);
mutex_destroy(&lp->bmux);
--
1.7.9.5
------------------------------------------------------------------------------
Managing the Performance of Cloud-Based Applications
Take advantage of what the Cloud has to offer - Avoid Common Pitfalls.
Read the Whitepaper.
http://pubads.g.doubleclick.net/gampad/clk?id=121051231&iu=/4140/ostg.clktrk
_______________________________________________
Linux-zigbee-devel mailing list
Linux-zigbee-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-zigbee-devel
