Le Mardi 22 Juillet 2003 15:47, Alain Belkadi a écrit : > Euh eth1 est pas up sur p166 on dirait (ou alors j'ai mal lu) ...
C'est normal, il n'y a pas de eth1 sur l'ordi p166. Quand je tente un ping du bip2 vers le p166, c'est le modem ADSL, connecté sur eth0, qui reçoit les paquets. A partir de l'ordi p166, les pings vers bip2 aboutissent aussi au modem en passant par les 2 cartes eth0 & eth1 du bip2. /etc/HOSTNAME sont corrects sur les 2 machines. /etc/hosts semble correct sur le p166 Voici le /etc/hosts du "maître" bip2 Je ne comprends pas l'utilité de la ligne 192.168.0.1 mais si je la supprime, rien ne change ------------------------------------------------------------------ # hosts This file describes a number of hostname-to-address # mappings for the TCP/IP subsystem. It is mostly # used at boot time, when no name servers are running. # On small systems, this file can be used instead of a # "named" name server. # Syntax: # # IP-Address Full-Qualified-Hostname Short-Hostname # # special IPv6 addresses #fe00::0 ipv6-localnet #ff00::0 ipv6-mcastprefix #ff02::1 ipv6-allnodes #ff02::2 ipv6-allrouters #ff02::3 ipv6-allhosts #::1 localhost ipv6-localhost ipv6-loopback 5/08/02 127.0.0.1 localhost 192.168.0.1 bip2.gamma 192.168.0.10 bip2.gamma bip2 192.168.0.2 p166.gamma p166 ------------------------------------------------------------------ Voici 2 extraits de dmesg sur le bip2 ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker http://www.scyld.com/network/ne2k-pci.html eth0: RealTek RTL-8029 found at 0xb800, IRQ 9, 00:50:BA:31:93:55. via-rhine.c:v3.22 05/02/2000 eth1: D-Link DFE-530TX PCI Fast Ethernet Adapter (rev.A) at 0xd000, 00:05:5d:e2:0a:54, IRQ 10. eth1: MII PHY found at address 8, status 0x782d advertising 01e1 Link 41e1. eth1: netdev_open() irq 10. eth1: Setting full-duplex based on MII #8 link partner capability of 41e1. eth1: Done netdev_open(), status 0c1a MII status: 782d. . . . . . . PPP generic driver version 2.4.1 IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver Registered PPPoX v0.5 Registered PPPoE v0.6.5 eth0: no IPv6 routers present eth1: no IPv6 routers present eth1: no IPv6 routers present eth0: no IPv6 routers present eth1: Shutting down ethercard, status was 0c1a. eth1: netdev_open() irq 10. eth1: Done netdev_open(), status 081a MII status: 782d. eth0: no IPv6 routers present eth1: no IPv6 routers present eth1: no IPv6 routers present eth0: no IPv6 routers present [EMAIL PROTECTED]:/etc > ------------------------------------------------------------------ Oû devrais-je chercher le "bug" ??? Grand merci d'avance Jean-Marie Lambert _______________________________________________________ Linux Mailing List - http://www.unixtech.be Subscribe/Unsubscribe: http://www.unixtech.be/mailman/listinfo/linux Archives: http://www.mail-archive.com/[EMAIL PROTECTED] IRC: efnet.unixtech.be:6667 - #unixtech