Am Mittwoch, 14. November 2007 01:14:52 schrieb Carl-Daniel Hailfinger: > On 13.11.2007 19:34, Harald Gutmann wrote: > > Am Dienstag, 13. November 2007 16:53:54 schrieb Carl-Daniel Hailfinger: > >> Strange. None of the changes in my patch show up in your superiotool > >> output. That either means these registers are special or some part of > >> the patch was ineffective or it was not applied. > > > > you are right! - it seems that somewhere a mistake happened to me, but i > > can't say exactly where. > > Thanks for retrying manually. > > > i attached a diff between the superiotool output from new linuxbios with > > your patch and the output from superiotool from an older revision of lb. > > also a second diff between the new lb version with your patch and the > > propritary bios is attached. (superiotool outputs) > > Thanks! It seems the patch is almost commit-ready. > > > flashrom also don't fail any more with the "old" error message, but it > > seems to hang on probing for the mx25l4005a: > > benchvice flashrom # ./flashrom -m gigabyte:m57sli -V > > Calibrating delay loop... 916M loops per second. OK. > > Found canidate at: 00000530-00000e44 > > Found LinuxBIOS table at 0x00000530. > > LinuxBIOS table found at 0x2ac58971e530. > > LinuxBIOS header(24) checksum: 5897 table(2324) checksum: 0c99 entries: > > 14 Vendor ID: GIGABYTE, part ID: m57sli > > Overwritten by command line, vendor ID: gigabyte, part ID: m57sli. > > Found chipset "NVIDIA MCP55", enabling flash write... OK. > > Found board "GIGABYTE GA-M57SLI-S4": enabling flash write... Serial flash > > segment 0xfffe0000-0xffffffff enabled > > Serial flash segment 0x000e0000-0x000fffff enabled > > Serial flash segment 0xffee0000-0xffefffff disabled > > Serial flash segment 0xfff80000-0xfffeffff enabled > > LPC write to serial flash enabled > > serial flash pin 29 > > OK. > > Probing for Am29F040B, 512 KB > > probe_29f040b: id1 0x7f, id2 0x45 > > Probing for Am29LV040B, 512 KB > > probe_29f040b: id1 0x7f, id2 0x45 > > Probing for Am29F016D, 2048 KB > > probe_29f040b: id1 0xff, id2 0xff > > Probing for AE49F2008, 256 KB > > probe_jedec: id1 0x7f, id2 0x45 > > Probing for At29C040A, 512 KB > > probe_jedec: id1 0x7f, id2 0x45 > > Probing for At29C020, 256 KB > > probe_jedec: id1 0x7f, id2 0x45 > > Probing for MBM29F400TC, 512 KB > > probe_m29f400bt: id1 0x7f, id2 0x4c > > Probing for MX29F002, 256 KB > > probe_29f002: id1 0x7f, id2 0x45 > > Probing for MX25L4005, 512 KB > > > > at this point nothing more happens. > > Can you abort flashrom with Ctrl-C or does the whole machine hang? Just flashrom hangs, and i'm able to abort it with Ctrl-C.
> If the machine does not hang, can you give me an Acked-by: tag? That way I > can commit and improve from there. Acked-by: Harald Gutmann <[EMAIL PROTECTED]> > Regards, > Carl-Daniel regards, Harald -- linuxbios mailing list [email protected] http://www.linuxbios.org/mailman/listinfo/linuxbios
