Hi Finn,
Am 26.12.2018 um 13:37 schrieb Finn Thain:
On powerpc, setting CONFIG_NVRAM=n builds a kernel with no NVRAM support.
Setting CONFIG_NVRAM=m enables the /dev/nvram misc device module without
enabling NVRAM support in drivers. Setting CONFIG_NVRAM=y enables the
misc device (built-in) and also enables NVRAM support in drivers.
m68k shares the valkyriefb driver with powerpc, and since that driver uses
NVRAM, it is affected by CONFIG_ATARI_SCSI, because of the use of
"select NVRAM".
Adopt the powerpc convention on m68k to avoid surprises.
Signed-off-by: Finn Thain <fth...@telegraphics.com.au>
Tested-by: Christian T. Steigies <c...@debian.org>
Acked-by: Michael Schmitz <schmitz...@gmail.com>
---
This patch temporarily disables CONFIG_NVRAM on Atari, to prevent build
failures when bisecting the rest of this patch series. It gets enabled
again with the introduction of CONFIG_HAVE_ARCH_NVRAM_OPS, once the
nvram_* global functions have been moved to an ops struct.
---
drivers/char/Kconfig | 5 +----
drivers/scsi/Kconfig | 6 +++---
drivers/scsi/atari_scsi.c | 7 ++++---
3 files changed, 8 insertions(+), 10 deletions(-)
diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
index 9d03b2ff5df6..5b54595dfe30 100644
--- a/drivers/char/Kconfig
+++ b/drivers/char/Kconfig
@@ -236,7 +236,7 @@ source "drivers/char/hw_random/Kconfig"
config NVRAM
tristate "/dev/nvram support"
- depends on ATARI || X86 || GENERIC_NVRAM
+ depends on X86 || GENERIC_NVRAM
---help---
If you say Y here and create a character special file /dev/nvram
with major number 10 and minor number 144 using mknod ("man mknod"),
@@ -254,9 +254,6 @@ config NVRAM
should NEVER idly tamper with it. See Ralf Brown's interrupt list
for a guide to the use of CMOS bytes by your BIOS.
- On Atari machines, /dev/nvram is always configured and does not need
- to be selected.
-
To compile this driver as a module, choose M here: the
module will be called nvram.
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 640cd1b31a18..924eb69e7fc4 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1381,14 +1381,14 @@ config ATARI_SCSI
tristate "Atari native SCSI support"
depends on ATARI && SCSI
select SCSI_SPI_ATTRS
- select NVRAM
---help---
If you have an Atari with built-in NCR5380 SCSI controller (TT,
Falcon, ...) say Y to get it supported. Of course also, if you have
a compatible SCSI controller (e.g. for Medusa).
- To compile this driver as a module, choose M here: the
- module will be called atari_scsi.
+ To compile this driver as a module, choose M here: the module will
+ be called atari_scsi. If you also enable NVRAM support, the SCSI
+ host's ID is taken from the setting in TT RTC NVRAM.
This driver supports both styles of NCR integration into the
system: the TT style (separate DMA), and the Falcon style (via
diff --git a/drivers/scsi/atari_scsi.c b/drivers/scsi/atari_scsi.c
index 89f5154c40b6..99e5729d910d 100644
--- a/drivers/scsi/atari_scsi.c
+++ b/drivers/scsi/atari_scsi.c
@@ -755,9 +755,10 @@ static int __init atari_scsi_probe(struct platform_device
*pdev)
if (ATARIHW_PRESENT(TT_SCSI) && setup_sg_tablesize >= 0)
atari_scsi_template.sg_tablesize = setup_sg_tablesize;
- if (setup_hostid >= 0) {
+ if (setup_hostid >= 0)
atari_scsi_template.this_id = setup_hostid & 7;
- } else {
+#ifdef CONFIG_NVRAM
+ else
/* Test if a host id is set in the NVRam */
if (ATARIHW_PRESENT(TT_CLK) && nvram_check_checksum()) {
unsigned char b = nvram_read_byte(16);
@@ -768,7 +769,7 @@ static int __init atari_scsi_probe(struct platform_device
*pdev)
if (b & 0x80)
atari_scsi_template.this_id = b & 7;
}
- }
+#endif
/* If running on a Falcon and if there's TT-Ram (i.e., more than one
* memory block, since there's always ST-Ram in a Falcon), then
