Bartlomiej Sieka wrote: > The bulk of this patch is taken from > http://patchwork.ozlabs.org/linuxppc/patch?q=Balakowicz&id=16197, with few > other updates, in particluar one posted by Anatolij Gustschin, which fixes > an Oops during boot. > > Signed-off-by: Marian Balakowicz <[EMAIL PROTECTED]> > --- > Anatolij, would you like to add your S-O-B? > > diff --git a/arch/powerpc/boot/dts/cm5200.dts > b/arch/powerpc/boot/dts/cm5200.dts > index 30737ea..8b2e8e4 100644 > --- a/arch/powerpc/boot/dts/cm5200.dts > +++ b/arch/powerpc/boot/dts/cm5200.dts > @@ -159,6 +159,7 @@ > }; > > [EMAIL PROTECTED] { > + device_type = "dma-controller"; > compatible = > "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; > reg = <1200 80>; > interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 > @@ -212,13 +213,31 @@ > [EMAIL PROTECTED] { > device_type = "network"; > compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; > - reg = <3000 800>; > + reg = <3000 400>; > local-mac-address = [ 00 00 00 00 00 00 ]; > interrupts = <2 5 0>; > interrupt-parent = <&mpc5200_pic>; > + phy-handle = <&phy0>; > + }; > + > + [EMAIL PROTECTED] { > + #address-cells = <1>; > + #size-cells = <0>; > + device_type = "mdio"; > + compatible = "fsl,mpc5200b-mdio"; > + reg = <3000 400>; // fec range, since we need to > setup fec interrupts > + interrupts = <2 5 0>; // these are for "mii command > finished", not link changes & co. > + interrupt-parent = <&mpc5200_pic>; > + > + phy0:[EMAIL PROTECTED] { > + device_type = "ethernet-phy"; > + reg = <0>; > + }; > }; > > [EMAIL PROTECTED] { > + #address-cells = <1>; > + #size-cells = <0>; > compatible = > "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; > reg = <3d40 40>; > interrupts = <2 10 0>; > @@ -231,4 +250,22 @@ > reg = <8000 4000>; > }; > }; > + > + lpb { > + model = "fsl,lpb"; > + compatible = "fsl,lpb"; > + #address-cells = <2>; > + #size-cells = <1>; > + ranges = <0 0 fc000000 2000000>; > + > + // 16-bit flash device at LocalPlus Bus CS0 > + [EMAIL PROTECTED],0 { > + compatible = "cfi-flash"; > + reg = <0 0 2000000>; > + bank-width = <2>; > + device-width = <2>; > + #size-cells = <1>; > + #address-cells = <1>; > + }; > + }; > }; > diff --git a/arch/powerpc/boot/dts/motionpro.dts > b/arch/powerpc/boot/dts/motionpro.dts > index 76951ab..9ca81ff 100644 > --- a/arch/powerpc/boot/dts/motionpro.dts > +++ b/arch/powerpc/boot/dts/motionpro.dts > @@ -127,6 +127,13 @@ > interrupt-parent = <&mpc5200_pic>; > }; > > + [EMAIL PROTECTED] { > + compatible = "mpc5200b-mscan\0mpc5200-mscan"; > + interrupts = <2 11 0>; > + interrupt-parent = <&mpc5200_pic>; > + reg = <900 80>; > + }; > +
If I remember correctly, the motionpro board has only _one_ MSCAN port wired. Therefore please discard the above hunk. Wolfgang. _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev
