Hello, On Sat, May 23, 2009 at 10:58 PM, Leon Woestenberg <leon.woestenb...@gmail.com> wrote: > using this tree: > git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git > > pci_enable_msi() fails on my MPC8315E-RDB board with PCIe device in
I found that the DTS for the MPC8315E-RDB is missing the msi bits. I added these, converted from the BSP (in old non-hex format): ipic-...@7c0 { compatible = "fsl,ipic-msi"; reg = <0x7c0 0x40>; msi-available-ranges = <0 0x100>; interrupts = < 0x43 8 0x4 8 0x51 8 0x52 8 0x56 8 0x57 8 0x58 8 0x59 8 >; interrupt-parent = < &ipic >; }; Now the MSI stuff gets set-up, pci_enable_msi() does not fault. My interrupt handler is still not called though. Partial log below: [ 246.907366] Setting up Freescale MSI support [ 247.858192] irq: irq 67 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 67 [ 249.323654] irq: irq 4 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 21 [ 250.779210] irq: irq 81 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 81 [ 252.244662] irq: irq 82 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 82 [ 253.710192] irq: irq 86 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 86 [ 255.175651] irq: irq 87 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 87 [ 256.641100] irq: irq 88 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 88 [ 258.106549] irq: irq 89 on host /i...@e0000000/interrupt-control...@700 mapped to virtual irq 89 [ 309.396138] pci_enable_msi() [ 309.399735] irq: irq 0 on host /i...@e0000000/ipic-...@7c0 mapped to virtual irq 24 [ 309.408030] fsl_compose_msi_msg: allocated srs: 0, ibs: 0 [ 309.414160] Enabled MSI interrupting. [ 309.418449] pci_read_config_byte(..., PCI_REVISION_ID, ...) [ 309.424754] Board revision: 0x01. [ 309.428690] pci_request_regions() [ 309.432654] pci_set_dma_mask() [ 309.436337] Using a 64-bit DMA mask. [ 309.455605] request_irq() [ 309.458925] Succesfully requested IRQ #24 with dev_id 0xc71c5440 debugfs shows: virq hwirq chip name host name 17 0x00009 IPIC /i...@e0000000/interrupt-control...@700 22 0x00010 IPIC /i...@e0000000/interrupt-control...@700 23 0x0000e IPIC /i...@e0000000/interrupt-control...@700 24 0x00000 FSL-MSI /i...@e0000000/ipic-...@7c0 32 0x00020 IPIC /i...@e0000000/interrupt-control...@700 33 0x00021 IPIC /i...@e0000000/interrupt-control...@700 34 0x00022 IPIC /i...@e0000000/interrupt-control...@700 35 0x00023 IPIC /i...@e0000000/interrupt-control...@700 36 0x00024 IPIC /i...@e0000000/interrupt-control...@700 37 0x00025 IPIC /i...@e0000000/interrupt-control...@700 38 0x00026 IPIC /i...@e0000000/interrupt-control...@700 Regards, Leon. _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev