The PCI-e addressing was originally patterned of the MPC8548CDS which has PCI1, PCI2, and PCI-e. Since this board only has PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS board. This does that by cutting the PCI/PCI-e I/O sizes from 16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000 (the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB range, removes the hole left by PCI2 from the aliases, and sets the clocks to match the oscillators that are actually on the board. With accompanying u-boot updates, PCI-e has been validated with both a sky2 card (1148:9e00) and an e1000 card (8086:108b). Signed-off-by: Paul Gortmaker <paul.gortma...@windriver.com> --- arch/powerpc/boot/dts/sbc8548.dts | 17 ++++++++--------- 1 files changed, 8 insertions(+), 9 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8548.dts b/arch/powerpc/boot/dts/sbc8548.dts index 9eefe00..a5bb015 100644 --- a/arch/powerpc/boot/dts/sbc8548.dts +++ b/arch/powerpc/boot/dts/sbc8548.dts @@ -26,8 +26,7 @@ serial0 = &serial0; serial1 = &serial1; pci0 = &pci0; - /* pci1 doesn't have a corresponding physical connector */ - pci2 = &pci2; + pci1 = &pci1; }; cpus { @@ -381,7 +380,7 @@ bus-range = <0 0>; ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x10000000 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00800000>; - clock-frequency = <66666666>; + clock-frequency = <66000000>; #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; @@ -390,7 +389,7 @@ device_type = "pci"; }; - pci2: p...@e000a000 { + pci1: p...@e000a000 { interrupt-map-mask = <0xf800 0x0 0x0 0x7>; interrupt-map = < @@ -403,9 +402,9 @@ interrupt-parent = <&mpic>; interrupts = <0x1a 0x2>; bus-range = <0x0 0xff>; - ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000 - 0x01000000 0x0 0x00000000 0xe3000000 0x0 0x08000000>; - clock-frequency = <33333333>; + ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2800000 0x0 0x08000000>; + clock-frequency = <33000000>; #interrupt-cells = <1>; #size-cells = <2>; #address-cells = <3>; @@ -419,11 +418,11 @@ device_type = "pci"; ranges = <0x02000000 0x0 0xa0000000 0x02000000 0x0 0xa0000000 - 0x0 0x20000000 + 0x0 0x10000000 0x01000000 0x0 0x00000000 0x01000000 0x0 0x00000000 - 0x0 0x08000000>; + 0x0 0x0800000>; }; }; }; -- 1.6.4.1 _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev