2009/10/22 Kumar Gala <ga...@kernel.crashing.org>: > Post the full kernel boot log. > > - k >
And this is the booting log of freescale linux kernel, which successfully mount the sata disk (sda3) as the rootfs: Using P2020 DS machine description Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=256Mb residual: 1280Mb Linux version 2.6.28.1-00295-g6dbbaa6-dirty (t...@xeon2) (gcc version 4.2.3 (Sour cery G++ Lite 4.2-171)) #1 SMP Thu Mar 5 14:31:02 CST 2009 CPU maps initialized for 1 thread per core console [udbg0] enabled setup_arch: bootmem mpc85xx_ds_setup_arch() Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->2 PCI host bridge /p...@ffe09000 (primary) ranges: MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000 IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000 Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->0 PCI host bridge /p...@ffe08000 ranges: MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000 Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0 PCI host bridge /p...@ffe0a000 ranges: MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000 IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000 MPC85xx DS board from Freescale Semiconductor arch: exit Zone PFN ranges: DMA 0x00000000 -> 0x00030000 Normal 0x00030000 -> 0x00030000 HighMem 0x00030000 -> 0x00080000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00080000 MMU: Allocated 1088 bytes of context maps for 255 contexts Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520192 Kernel command line: root=/dev/sda3 rw console=ttyS0,115200 mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs mpic: ISU size: 256, shift: 8, mask: ff mpic: Initializing for 256 sources i8259 legacy interrupt controller initialized PID hash table entries: 4096 (order: 12, 16384 bytes) clocksource: timebase mult[400029f] shift[22] registered Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2073196k/2097152k available (5300k kernel code, 23088k reserved, 168k da ta, 186k bss, 220k init) SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop... 124.67 BogoMIPS (lpj=249344) Mount-cache hash table entries: 512 mpic: requesting IPIs ... Processor 1 found. Brought up 2 CPUs net_namespace: 496 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01) pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:01:00.0: PME# supported from D0 D3hot D3cold pci 0000:01:00.0: PME# disabled pci 0000:02:1c.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:1c.0: PME# disabled pci 0000:02:1c.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:1c.1: PME# disabled pci 0000:02:1c.2: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:1c.2: PME# disabled pci 0000:02:1c.3: PME# supported from D0 D3hot D3cold pci 0000:02:1c.3: PME# disabled pci 0000:02:1f.1: PME# supported from D3hot pci 0000:02:1f.1: PME# disabled pci 0000:01:00.0: transparent bridge pci 0001:03:00.0: ignoring class b20 (doesn't match header type 01) pci 0001:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0001:03:00.0: PME# disabled pci 0002:05:00.0: ignoring class b20 (doesn't match header type 01) pci 0002:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0002:05:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: 0x1000-0x1fff pci 0000:01:00.0: MEM window: 0xa0000000-0xa00fffff pci 0000:01:00.0: PREFETCH window: disabled pci 0000:00:00.0: PCI bridge, secondary bus 0000:01 pci 0000:00:00.0: IO window: 0x00-0xffff pci 0000:00:00.0: MEM window: 0xa0000000-0xbfffffff pci 0000:00:00.0: PREFETCH window: disabled pci 0000:00:00.0: enabling device (0106 -> 0107) pci 0001:03:00.0: PCI bridge, secondary bus 0001:04 pci 0001:03:00.0: IO window: 0x00-0xffff pci 0001:03:00.0: MEM window: 0x80000000-0x9fffffff pci 0001:03:00.0: PREFETCH window: disabled pci 0001:03:00.0: enabling device (0106 -> 0107) pci 0002:05:00.0: PCI bridge, secondary bus 0002:06 pci 0002:05:00.0: IO window: 0x00-0xffff pci 0002:05:00.0: MEM window: 0xc0000000-0xdfffffff pci 0002:05:00.0: PREFETCH window: disabled pci 0002:05:00.0: enabling device (0106 -> 0107) bus: 00 index 0 io port: [0x00-0xffff] bus: 00 index 1 mmio: [0xa0000000-0xbfffffff] bus: 01 index 0 io port: [0x00-0xffff] bus: 01 index 1 mmio: [0xa0000000-0xbfffffff] bus: 01 index 2 mmio: [0x0-0x0] bus: 01 index 3 mmio: [0x0-0x0] bus: 02 index 0 io port: [0x1000-0x1fff] bus: 02 index 1 mmio: [0xa0000000-0xa00fffff] bus: 02 index 2 mmio: [0x0-0x0] bus: 02 index 3 io port: [0x00-0xffff] bus: 02 index 4 mmio: [0xa0000000-0xbfffffff] bus: 02 index 5 mmio: [0x0-0x0] bus: 02 index 6 mmio: [0x0-0x0] bus: 03 index 0 io port: [0xfffee000-0xffffdfff] bus: 03 index 1 mmio: [0x80000000-0x9fffffff] bus: 04 index 0 io port: [0xfffee000-0xffffdfff] bus: 04 index 1 mmio: [0x80000000-0x9fffffff] bus: 04 index 2 mmio: [0x0-0x0] bus: 04 index 3 mmio: [0x0-0x0] bus: 05 index 0 io port: [0xfffdc000-0xfffebfff] bus: 05 index 1 mmio: [0xc0000000-0xdfffffff] bus: 06 index 0 io port: [0xfffdc000-0xfffebfff] bus: 06 index 1 mmio: [0xc0000000-0xdfffffff] bus: 06 index 2 mmio: [0x0-0x0] bus: 06 index 3 mmio: [0x0-0x0] SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 mpc85xx_spi_init >> audit: initializing netlink socket (disabled) type=2000 audit(0.720:1): initialized highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 o...@monad.swb.de). NTFS driver 2.1.29 [Flags: R/O]. msgmni has been set to 1490 alg: No test for cipher_null (cipher_null-generic) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Generic non-volatile memory driver v1.1 Serial: 8250/16550 driver2 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A console handover: b oot [udbg0] -> real [ttyS0] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A brd: module loaded loop: module loaded nbd: registered device at major 43 e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 e1000e: Copyright (c) 1999-2008 Intel Corporation. Gianfar MII Bus: probed Gianfar MII Bus: probed Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:02:00:fd eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:02:01:fd eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size eth2: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:02:02:fd eth2: Running with NAPI enabled eth2: 256/256 RX/TX BD ring size sky2 driver version 1.22 st: Version 20080504, fixed bufsize 32768, s/g segs 256 Driver 'st' needs updating - please use bus_type methods Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ahci 0000:02:1f.1: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:02:1f.1: flags: ncq sntf ilck pm led clo pmp pio slum part scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 abar m1...@0xa0003400 port 0xa0003500 irq 18 ata2: SATA max UDMA/133 abar m1...@0xa0003400 port 0xa0003580 irq 18 ata3: SATA max UDMA/133 abar m1...@0xa0003400 port 0xa0003600 irq 18 ata4: SATA max UDMA/133 abar m1...@0xa0003400 port 0xa0003680 irq 18 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: Hitachi HDP725016GLA380, GMBOA52A, max UDMA/133 ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA Hitachi HDP72501 GMBO PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi4 : pata_ali scsi5 : pata_ali ata5: PATA max UDMA/133 cmd 0x1000 ctl 0x1008 bmdma 0x1020 irq 14 ata6: PATA max UDMA/133 cmd 0x1010 ctl 0x1018 bmdma 0x1028 irq 14 fsl_m25p80 spi28672.0: s25sl128b (16384 Kbytes) fsl_espi.0: Freescale eSPI Controller driver at 0xf1094000 (irq = 59) usbmon: debugfs is not available ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_hcd 0000:02:1c.3: Found HC with no IRQ. Check BIOS/PCI 0000:02:1c.3 setup! ehci_hcd 0000:02:1c.3: init 0000:02:1c.3 fail, -19 ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd 0000:02:1c.0: Found HC with no IRQ. Check BIOS/PCI 0000:02:1c.0 setup! ohci_hcd 0000:02:1c.0: init 0000:02:1c.0 fail, -19 ohci_hcd 0000:02:1c.1: Found HC with no IRQ. Check BIOS/PCI 0000:02:1c.1 setup! ohci_hcd 0000:02:1c.1: init 0000:02:1c.1 fail, -19 ohci_hcd 0000:02:1c.2: Found HC with no IRQ. Check BIOS/PCI 0000:02:1c.2 setup! ohci_hcd 0000:02:1c.2: init 0000:02:1c.2 fail, -19 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i8042.c: No controller found. rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one day, 114 bytes nvram usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18rc3. ALSA device list: No soundcards found. IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc_cmos rtc_cmos: setting system clock to 1970-06-23 12:08:10 UTC (14990890) kjournald starting. Commit interval 5 seconds EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended EXT3 FS on sda3, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing unused kernel memory: 220k init Mounting /proc and /sys Starting the hotplug events dispatcher udevd Synthesizing initial hotplug events Setting the hostname to p2020ds Running depmod WARNING: Couldn't open directory /lib/modules/2.6.28.1-00295-g6dbbaa6-dirty: No such file or directory FATAL: Could not open /lib/modules/2.6.28.1-00295-g6dbbaa6-dirty/modules.dep.tem p for writing: No such file or directory Mounting filesystems Starting syslogd and klogd Running sysctl Setting up networking on loopback device: Setting up networking on eth0: ADDRCONF(NETDEV_UP): eth0: link is not ready Adding static route for default gateway to 192.168.1.1: Setting nameserver to 192.168.1.1 in /etc/resolvADDRCONF(NETDEV_UP): eth1: link is not ready .conf: Setting up networking on eth1: Adding static route for default gateway to 192.168.1.1: Setting nameserver to 192.168.1.1 in /etc/resolv.conf: Starting inetd: Starting the port mapper: Setting time from ntp server: /bin/ntpclient: option requires an argument -- h Usage: /bin/ntpclient [-c count] [-d] [-g goodness] -h hostname [-i interval] [-l] [-p port] [-r] [-s] Welcome to Freescale Semiconductor Embedded Linux Environment !!!!! WARNING !!!!!!! The default password for the root account is: root please change this password using the 'passwd' command and then edit this message (/etc/issue) to remove this message p2020ds login: PHY: m...@24520:00 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev