The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Features:
*CPU speed (frequency): up to 600 MHz
*Five-stage pipeline, executes up to one instruction per cycle
*16 KB-I/16 KB-D L1 caches, two-way set-associative
*128 KB on-chip memory
*128-bit processor local bus (PLB)
*Separate 128-bit read and 128-bit write data bus
*Up to 6.4 GBps of peak on-chip bandwidth at 200 MHz
*On-chip DDR2 SDRAM controller with 16-bit interface
*Support for one rank of DDR2 SDRAM up to 512 MB
*One Gen 1 single-lane PCI Express interface
*One Gen 1 single lane miniPCIe interface
*Configurable as root or endpoint
*One SATA controller operating at up to 3.0 Gbps with integrated SerDes
*Two Ethernet 10/100/1000 Mbps, full-duplex MACs (RGMII/TMII/MII)
*TCP/IP acceleration hardware, QoS, and jumbo frame support
*IEEE 1588 V1 and V2 support
*On-chip IPsec acceleration with header/trailer processing
*Supports DES, 3DES, and AES encryption
*Operates at 1.5/12/480 Mbps bus speeds
version 2:
1. compressed defconfig.
2. cleaned dts.
3. cputable with single cpu entry instead of 4 similar entries.
4. removed uart specific changes.
Signed-off-by: Tanmay Inamdar <tinam...@apm.com>
---
arch/powerpc/boot/dts/klondike.dts | 227 +++++++++++++++++++++++++++
arch/powerpc/configs/40x/klondike_defconfig | 55 +++++++
arch/powerpc/kernel/cputable.c | 13 ++
arch/powerpc/platforms/40x/Kconfig | 11 ++
arch/powerpc/platforms/40x/ppc40x_simple.c | 1 +
5 files changed, 307 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/klondike.dts
create mode 100644 arch/powerpc/configs/40x/klondike_defconfig
diff --git a/arch/powerpc/boot/dts/klondike.dts
b/arch/powerpc/boot/dts/klondike.dts
new file mode 100644
index 0000000..8c94290
--- /dev/null
+++ b/arch/powerpc/boot/dts/klondike.dts
@@ -0,0 +1,227 @@
+/*
+ * Device Tree for Klondike (APM8018X) board.
+ *
+ * Copyright (c) 2010, Applied Micro Circuits Corporation
+ * Author: Tanmay Inamdar <tinam...@apm.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/dts-v1/;
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "apm,klondike";
+ compatible = "apm,klondike";
+ dcr-parent = <&{/cpus/cpu@0}>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,apm8018x";
+ reg = <0x00000000>;
+ clock-frequency = <300000000>; /* Filled in by U-Boot */
+ timebase-frequency = <300000000>; /* Filled in by
U-Boot */
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <16384>; /* 16 kB */
+ d-cache-size = <16384>; /* 16 kB */
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* Filled in by U-Boot */
+ };
+
+ UIC0: interrupt-controller {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0x0c0 0x010>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0x0d0 0x010>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC2: interrupt-controller2 {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <2>;
+ dcr-reg = <0x0e0 0x010>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0x0a 0x4 0x0b 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC3: interrupt-controller3 {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <3>;
+ dcr-reg = <0x0f0 0x010>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0x10 0x4 0x11 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ plb {
+ compatible = "ibm,plb4";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ SDRAM0: memory-controller {
+ compatible = "ibm,sdram-apm8018x";
+ dcr-reg = <0x010 0x002>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal2";
+ dcr-reg = <0x180 0x062>;
+ num-tx-chans = <2>;
+ num-rx-chans = <16>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-parent = <&UIC1>;
+ interrupts = </*TXEOB*/ 0x6 0x4
+ /*RXEOB*/ 0x7 0x4
+ /*SERR*/ 0x1 0x4
+ /*TXDE*/ 0x2 0x4
+ /*RXDE*/ 0x3 0x4>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x20000000 0x20000000 0x30000000
+ 0x50000000 0x50000000 0x10000000
+ 0x60000000 0x60000000 0x10000000
+ 0xFE000000 0xFE000000 0x00010000>;
+ dcr-reg = <0x100 0x020>;
+ clock-frequency = <300000000>; /* Filled in by U-Boot */
+
+ RGMII0: emac-rgmii@400a2000 {
+ compatible = "ibm,rgmii";
+ reg = <0x400a2000 0x00000010>;
+ has-mdio;
+ };
+
+ TAH0: emac-tah@400a3000 {
+ compatible = "ibm,tah";
+ reg = <0x400a3000 0x100>;
+ };
+
+ TAH1: emac-tah@400a4000 {
+ compatible = "ibm,tah";
+ reg = <0x400a4000 0x100>;
+ };
+
+ EMAC0: ethernet@400a0000 {
+ compatible = "ibm,emac4", "ibm-emac4sync";
+ interrupt-parent = <&EMAC0>;
+ interrupts = <0x0>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0x0 &UIC0 0x13 0x4>;
+ reg = <0x400a0000 0x00000100>;
+ local-mac-address = [000000000000]; /* Filled
in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0x0>;
+ mal-rx-channel = <0x0>;
+ cell-index = <0>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <4096>;
+ tx-fifo-size = <2048>;
+ phy-mode = "rgmii";
+ phy-address = <0x2>;
+ turbo = "no";
+ phy-map = <0x00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ EMAC1: ethernet@400a1000 {
+ compatible = "ibm,emac4", "ibm-emac4sync";
+ status = "disabled";
+ interrupt-parent = <&EMAC1>;
+ interrupts = <0x0>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0x0 &UIC0 0x14 0x4>;
+ reg = <0x400a1000 0x00000100>;
+ local-mac-address = [000000000000]; /* Filled
in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <1>;
+ mal-rx-channel = <8>;
+ cell-index = <1>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <4096>;
+ tx-fifo-size = <2048>;
+ phy-mode = "rgmii";
+ phy-address = <0x3>;
+ turbo = "no";
+ phy-map = <0x00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <1>;
+ tah-device = <&TAH1>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ mdio-device = <&EMAC0>;
+ };
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@50001000";
+ };
+};
diff --git a/arch/powerpc/configs/40x/klondike_defconfig
b/arch/powerpc/configs/40x/klondike_defconfig
new file mode 100644
index 0000000..c0d228d
--- /dev/null
+++ b/arch/powerpc/configs/40x/klondike_defconfig
@@ -0,0 +1,55 @@
+CONFIG_40x=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_WALNUT is not set
+CONFIG_APM8018X=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_MATH_EMULATION=y
+# CONFIG_MIGRATION is not set
+# CONFIG_SUSPEND is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_PROC_DEVICETREE=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_SAS_ATTRS=y
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_UNIX98_PTYS is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_CRAMFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_AVERAGE=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_FTRACE is not set
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index edae5bb..ce59693 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -1505,6 +1505,19 @@ static struct cpu_spec __initdata cpu_specs[] = {
.machine_check = machine_check_4xx,
.platform = "ppc405",
},
+ { /* APM8018X */
+ .pvr_mask = 0xffff0000,
+ .pvr_value = 0x7ff11432,
+ .cpu_name = "APM8018X",
+ .cpu_features = CPU_FTRS_40X,
+ .cpu_user_features = PPC_FEATURE_32 |
+ PPC_FEATURE_HAS_MMU | PPC_FEATURE_HAS_4xxMAC,
+ .mmu_features = MMU_FTR_TYPE_40x,
+ .icache_bsize = 32,
+ .dcache_bsize = 32,
+ .machine_check = machine_check_4xx,
+ .platform = "ppc405",
+ },
{ /* default match */
.pvr_mask = 0x00000000,
.pvr_value = 0x00000000,
diff --git a/arch/powerpc/platforms/40x/Kconfig
b/arch/powerpc/platforms/40x/Kconfig
index 1530229..8883f2c 100644
--- a/arch/powerpc/platforms/40x/Kconfig
+++ b/arch/powerpc/platforms/40x/Kconfig
@@ -186,3 +186,14 @@ config IBM405_ERR51
# bool
# depends on !STB03xxx && PPC4xx_DMA
# default y
+#
+
+config APM8018X
+ bool "APM8018X"
+ depends on 40x
+ default n
+ select PPC40x_SIMPLE
+ help
+ This option enables support for the AppliedMicro APM8018X evaluation
+ board.
+
diff --git a/arch/powerpc/platforms/40x/ppc40x_simple.c
b/arch/powerpc/platforms/40x/ppc40x_simple.c
index e8dd5c5..2f8fde6 100644
--- a/arch/powerpc/platforms/40x/ppc40x_simple.c
+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
@@ -55,6 +55,7 @@ static const char *board[] __initdata = {
"amcc,haleakala",
"amcc,kilauea",
"amcc,makalu",
+ "apm,klondike",
"est,hotfoot"
};
--
1.6.1.rc3
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
