Hi Jean-Samuel, Actually, I removed the console and null created by buildroot and create them manually using make node. This time the system freezes at this point. "Freeing unused kernel memory: 76k init"
loaded at: 00400000 004CE1A0 board data at: 004CC120 004CC19C relocated to: 0040405C 004040D8 zimage at: 00404E94 004CB08A avail ram: 004CF000 10000000 Linux/PPC load: console=ttyS0,9600 root=/dev/xsa2 init=/bin/sh Uncompressing Linux...done. Now booting the kernel Linux version 2.6.24-rc3 ([EMAIL PROTECTED]) (gcc version 4.2.2) #1 Wed Jan 2 14:3 7:58 CET 2008 Xilinx ML300 Reference System (Virtex-II Pro) Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 HighMem 655 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,9600 root=/dev/xsa2 init=/bin/sh Xilinx INTC #0 at 0x41200000 mapped to 0xEF5FE000 PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 258048k available (1288k kernel code, 436k data, 76k init, 0k highmem) Mount-cache hash table entries: 512 net_namespace: 64 bytes NET: Registered protocol family 16 sysctl table check failed: /kernel/l2cr .1.31 Missing strategy Call Trace: [cfc1fe20] [c0008148] show_stack+0x58/0x188 (unreliable) [cfc1fe68] [c0038908] set_fail+0x50/0x68 [cfc1fe80] [c0038f7c] sysctl_check_table+0x65c/0x6ac [cfc1fee8] [c0038f8c] sysctl_check_table+0x66c/0x6ac [cfc1ff50] [c0026c58] register_sysctl_table+0x64/0xb4 [cfc1ff50] [c0026c58] register_sysctl_table+0x64/0xb4 [cfc1ff70] [c019b228] kernel_init+0x104/0x290 [cfc1fff0] [c0004af8] kernel_thread+0x44/0x60 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 2) is a 16550A console [ttyS0] enabled xsysace xsysace.0: Xilinx SystemACE revision 1.0.12 xsysace xsysace.0: capacity: 1981728 sectors xsa: xsa1 xsa2 xsa3 Xilinx SystemACE device driver, major=254 i8042.c: No controller found. mice: PS/2 mouse device common for all mice VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 76k init Warning: unable to open an initial console. init has generated signal 11 but has no handler for it Kernel panic - not syncing: Attempted to kill init! Rebooting in 180 seconds..<NULL> loaded at: 00400000 004CE1A0 board data at: 004CC120 004CC19C relocated to: 0040405C 004040D8 zimage at: 00404E94 004CB08A avail ram: 004CF000 10000000 Linux/PPC load: console=ttyS0,9600 root=/dev/xsa2 init=/bin/sh Uncompressing Linux...done. Now booting the kernel Linux version 2.6.24-rc3 ([EMAIL PROTECTED]) (gcc version 4.2.2) #1 Wed Jan 2 14:3 7:58 CET 2008 Xilinx ML300 Reference System (Virtex-II Pro) Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 HighMem 6553 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS0,9600 root=/dev/xsa2 init=/bin/sh Xilinx INTC #0 at 0x41200000 mapped to 0xEF5FE000 PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 258048k available (1288k kernel code, 436k data, 76k init, 0k highmem) Mount-cache hash table entries: 512 net_namespace: 64 bytes NET: Registered protocol family 16 sysctl table check failed: /kernel/l2cr .1.31 Missing strategy Call Trace: [cfc1fe20] [c0008148] show_stack+0x58/0x188 (unreliable) [cfc1fe68] [c0038908] set_fail+0x50/0x68 [cfc1fe80] [c0038f7c] sysctl_check_table+0x65c/0x6ac [cfc1fee8] [c0038f8c] sysctl_check_table+0x66c/0x6ac [cfc1ff50] [c0026c58] register_sysctl_table+0x64/0xb4 [cfc1ff68] [c019ed4c] register_ppc_htab_sysctl+0x18/0x2c [cfc1ff70] [c019b228] kernel_init+0x104/0x290 [cfc1fff0] [c0004af8] kernel_thread+0x44/0x60 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 2) is a 16550A console [ttyS0] enabled xsysace xsysace.0: Xilinx SystemACE revision 1.0.12 xsysace xsysace.0: capacity: 1981728 sectors xsa: xsa1 xsa2 xsa3 Xilinx SystemACE device driver, major=254 i8042.c: No controller found. mice: PS/2 mouse device common for all mice VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 76k init -----Original Message----- From: mojtaba [mailto:[EMAIL PROTECTED] Sent: Thursday, January 03, 2008 4:58 PM To: 'linuxppc-embedded@ozlabs.org' Subject: RE: File system problem Hi, Thank you very much for your answers. But I have both console and null in /dev. -rw-rw-rw- 1 mojtaba mojtaba 0 2007-12-26 15:50 console -rw-rw-rw- 1 mojtaba mojtaba 0 2007-12-26 15:50 null They have been created by buildroot. Do I need to create them manually? Actually the size of both of them is 0 and both are empty files. Is that a problem? Thank you in advance and best regards, Mojtaba -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jean-Samuel Chenard Sent: Thursday, January 03, 2008 4:33 AM To: linuxppc-embedded@ozlabs.org; [EMAIL PROTECTED] Subject: RE: File system problem > Date: Wed, 2 Jan 2008 19:50:13 +0100 > From: "mojtaba" > I am trying to boot a root file system build by buildroot. But I got this > error" init has generated signal 11 but has no handler for it". > > My kernel version is 2.6.24-rc3 > My target system is PPC 405 (XILINX VIRTEX II pro) I am using the 26-12-2007 > snapshot of buildroot. [ ... ] > Warning: unable to open an initial console. > init has generated signal 11 but has no handler for it Kernel panic - not Hi Mojtaba, I got a similar error on my ML-310 when I tried a new root filesystem. As far as I recall, I needed to make sure that two entries existed in /dev, namely: crw------- 1 root root 5, 1 Jan 1 05:18 console crw-rw---- 1 root root 1, 3 Dec 10 2007 null I think that you are missing /dev/console and then init cannot run since it has nowhere to put its standard output. You can make those by mounting your CF card on your development host and (as root) make the nodes: # mknod -m 660 /dev/console c 5 1 # mknod -m 660 /dev/null c 1 3 In my case, I use the UartLite (ttyUL0) serial port driver, but I'm pretty sure this is going to fix the problem you are observing. Regards, Jean-Samuel -- Ph.D. candidate Integrated Microsystems Laboratory McGill University, Montréal, QC, CANADA Web Page: http://chaos.ece.mcgill.ca _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded