OK thanks anyway , and yes ws001 is the name of the terminal in DHCP Bruno
El Mar 27 May 2003 15:41, escribió: > I don't know if the name of your machine is really ws001, but maybe you > could try to use the ip adress insted. > I don't think that it is necessary to write all stuff again from your > default, just the things wich are different are enougth > I wrote my owns lines from my conf down there, but you told before that > the Microsoft protocol was not appreciate ( but who would ;-) ). > Sorry, but it is all help that you can get from a newbie like me ! > Regards > Jean Christophe > > Bruno Luciani a écrit: > >Yes here is , the error in the terminal is can' t open serial device > >/dev/ttyS0 or something else and the mouse is conected and chequed that it > >works ok in this port , I dont't know what is wrong > >I would apreciate your help. > > > >Thanks in advance > > > >////////////////////////////////////////////////////////////////////////// > >//// # > ># Config file for the Linux Terminal Server Project (www.ltsp.org) > ># > > > >[Default] > > SERVER = 192.168.10.254 > > XSERVER = auto > > X_MOUSE_PROTOCOL = "PS/2" > > X_MOUSE_DEVICE = "/dev/psaux" > > X_MOUSE_RESOLUTION = 400 > > X_MOUSE_BUTTONS = 3 > > USE_XFS = N > > LOCAL_APPS = N > > RUNLEVEL = 5 > > > >#------------------------------------------------------------------------- > >----- # > ># Example of specifying X settings for a workstation > ># > >[ws001] > > XSERVER = auto > > LOCAL_APPS = N > > USE_NFS_SWAP = N > > SWAPFILE_SIZE = 48m > > RUNLEVEL = 5 > > X_MOUSE_PROTOCOL = "Microsoft" > X_MOUSE_DEVICE = "/dev/ttyS0" > X_MOUSE_RESOLUTION = 50 > > > X_MOUSE_PROTOCOL = "Auto" > > X_MOUSE_DEVICE = "/dev/ttyS0" > > X_MOUSE_RESOLUTION = 50 > > X_MOUSE_BUTTONS = 2 > > X_MOUSE_EMULATE3BTN = Y > > > >[ws002] > > XSERVER = XF86_SVGA > > LOCAL_APPS = N > > USE_NFS_SWAP = N > > SWAPFILE_SIZE = 64m > > RUNLEVEL = 3 > > > ># > ># ws004 is my virtual workstation running in a VMware session > ># > >[ws004] > > DNS_SERVER = 192.168.10.254 > > XSERVER = auto > > X4_BUSID = "PCI:0:15:0" > > X_MODE_0 = 800x600 > > LOCAL_APPS = N > > USE_NFS_SWAP = N > > SWAPFILE_SIZE = 64m > > RUNLEVEL = 5 > > > >#------------------------------------------------------------------------- > >----- # > ># Example of a workstation configured to load some modules > ># > >#[ws001] > ># MODULE_01 = agpgart.o # This is for i810 video > ># MODULE_02 = uart401.o > ># MODULE_03 = sb.o io=0x220 irq=5 dma=1 > ># MODULE_04 = opl3.o > > > >#------------------------------------------------------------------------- > >----- # > ># Example of ws001 configured for local apps > ># > >#[ws001] > ># LOCAL_APPS = Y > ># LOCAL_WM = Y > ># NIS_DOMAIN = ltsp > ># NIS_SERVER = 192.168.0.254 > > > >#------------------------------------------------------------------------- > >----- # > ># Example of a serial printer attached to /dev/ttyS1 on workstation ws001 > ># > >#[ws001] > ># PRINTER_0_DEVICE = /dev/ttyS1 > ># PRINTER_0_TYPE = S # P-Parallel, S-Serial > ># PRINTER_0_PORT = 9100 # tcp/ip port: defaults to 9100 > ># PRINTER_0_SPEED = 9600 # baud rate: defaults to 9600 > ># PRINTER_0_FLOWCTRL = S # Flow control: S-Software (XON/XOFF), > ># # H-Hardware (CTS/RTS) > ># PRINTER_0_PARITY = N # Parity: N-None, E-Even, O-Odd > ># # (defaults to 'N') > ># PRINTER_0_DATABITS = 8 # Databits: 5,6,7,8 (defaults to 8) > > > >////////////////////////////////////////////////////////////////////////// > >/////////////////////////////////////////////////////////// > > > >El Lun 26 May 2003 11:00, escribió: > >>Bruno Luciani a écrit: > >>>I have problem configuring my terminal with serial mouse > >>>Using default setup for ltsp.conf ( ps2 mouse) > >>> > >>>my terminal startx ok but mouse don't work ( is a serial mouse :-) > >>>but when I change setup to correct devide ttyS0 and Microsoft type > >>>X don't start anymore > >>> > >>>I am using Mandrake 9.1 and the last version of ltsp. > >>> > >>>thanks for any help > >>> > >>>Bruno Luciani > >>>Buenos Aires > >>>Argentina > >>> > >>> > >>>------------------------------------------------------- > >>>This SF.net email is sponsored by: ObjectStore. > >>>If flattening out C++ or Java code to make your application fit in a > >>>relational database is painful, don't do it! Check out ObjectStore. > >>>Now part of Progress Software. http://www.objectstore.net/sourceforge > >>>_____________________________________________________________________ > >>>Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: > >>> https://lists.sourceforge.net/lists/listinfo/ltsp-discuss > >>>For additional LTSP help, try #ltsp channel on irc.freenode.net > >> > >>can you copy your lst.conf > >>Jean Christophe ------------------------------------------------------- This SF.net email is sponsored by: ObjectStore. If flattening out C++ or Java code to make your application fit in a relational database is painful, don't do it! Check out ObjectStore. Now part of Progress Software. http://www.objectstore.net/sourceforge _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.freenode.net
